Dinstar DAG2000-16S Manuel utilisateur

Quick Installation Guide

DAG2000-16S

DAG2000-24S/32S

DAG2500-48S/64S/72S

DAG3000-112S

Thanks for Choosing Dinstar’s VoIP Gateway!

Please read this guide carefully before installing the gateway. If you need any technical

support, .please contact us

Tel: +86 755 61919966

Email: support@dinstar.com

Website: www.dinstar.com

Please check the model of your gateway before installation,and then refer to corresponding

installation instructions.

Product Model & Number of Ports

Description of Indicators

Indicator Deﬁnition Status Description

Power Indicator

Running Indicator

Telephone In-use

Indicator

Off

The gateway is powered on

The gateway has no power input

or power supply is abnormal

Off

Slow Flashing

Flashing

Link (Green)

Speed

PWR

RUN

FXS

WAN/LAN

The gateway is running properly

SIP account is registered successfully

The gateway is running improperly

FXS port is currently occupied by a call

FXS port is idle or faulty

The gateway is properly connected to network

The gateway is not connected to network

or network connection is improper

Work at 100Mbps

Work at 10Mbps

Fast Flashing

Model

Port Type

DAG2000-16S

LAN RJ11 RJ21

0 0

416

DAG2000-24S

DAG2000-32S

DAG2500-48S

DAG2500-64S

DAG2500-72S

RJ45

40 0

DAG3000-112S

Dinstar’s VoIP gateways have three types of FXS ports, namely RJ11,RJ21 and RJ45. For the

number of ports of each model,please refer to the table above.

Indicators & Interfaces

DAG2000-16S

DAG2000-24S/32S

Power Indicator

Power Switch

Power Jack LAN Ports

LAN Ports

Console Port

Reset Button

Ground Point

Running Indicator

Power Indicator

Running Indicator

Telephone In-use Indicator FXS Ports 0-15

FXS Ports 0-31 (RJ11)

FXS Ports (RJ21)

Note: The position of each indicator and interface of DAG2000-24S is the same as on the

DAG2000-32S.

Reset Button

Telephone In-use Indicator

Power Jack

Console Port

DAG2500-48S/64S/72S

DAG3000-112S

Power Indicator

Running Indicator

Alarm Indicator

Network Link Indicator Telephone In-use Indicator

Power Switch

Screw

Telephone In-use

Indicators Power Indicator

Running Indicator

FXS Ports

Power Switch

Ground Point

Power Jack Switch for Master/Slave Power (Reserved)

LAN Ports

Console Port

User board

User Board

Main Control Board

Power Jack Console Port

Reset Button FXS Ports(RJ21)

Note: The position of each indicator and interface of DAG2500-48S and DAG2500-64S is the

same as on DAG2000-72S.

Ground Point LAN Ports

Reset Button

Installation Attentions

Installation Instructions

Connection Diagram for DAG2000-16S

Connect gateway with network via a switch

Network Cable

Switch

RJ11 telephone line

Telephone

Connect FXS ports with analog phones

Connect gateway with power input and ground point

100-240V AC

Grounding Cable

Ground Point

Network Cable

Please check the FXS type of your gateway before installation:

DAG2000-16S is equipped with RJ11 ports;

DAG2000-24S/32S is equipped with both RJ11 and RJ21 ports;

DAG2500-48S/64S72S is equipped with RJ21 ports;

DAG3000-112S is equipped with RJ45 ports.

For the wire sequence of RJ21 and RJ45,please refer to Section 6 Wire Sequence of this manual.

Anti-jamming: to reduce the interference with telephone calls, it’s highly recommended that telephone

lines connected to the gateway should be placed away from power cables;

Power supply: the gateway accepts AC input voltage of 100-240V. Please ensure safe and stable power

supply;

Network bandwidth:please ensure there is enough network bandwidth so as to guarantee stabilized

running of the gateway；

Ventilation: to avoid overheating, please do not pile up the gateway with other devices and make sure the

gateway has good ventilation around.

Temperature and humidity: to avoid any accident that might cause malfunction , it’s advised to install the

gateway in an equipment room where temperature and humidity are appropriate ；

Mechanical load: please make sure the gateway is placed steadily to avoid damage. It’ s highly advised to

horizontally place the gateway on a ﬂat surface or a cabinet.

Connection Diagram forDAG2000-24S/32S

Connect gateway with network via a switch

Type 2: Connect FXS ports with analog phones

Type 1: Connect FXS ports with analog phones

Connect gateway with power input and ground point

Network Cable

Switch

Telephone

Telephpne

RJ11 Cable(Telephone Line)

RJ21 Cable

100-240V AC

Grounding Cable

Ground Point

Connection Diagram for DAG2500-48S/64S/72S

Connect gateway with network via a switch

Network Cable

Switch

Connect FXS ports with analog phones

Telephone

RJ21 Cable

Connect gateway with power input and ground point

100-240V AC

Grounding Cable

Gound Point

Connection Diagram for DAG3000-112S

Connect gateway with network via a switch

Network Cable

Switch

Connect FXS ports with analog phones

Telephone

RJ45 Cable

Power Connection & Grounding

100-240V AC

Grounding

Cable

Ground

Point

Network Cable

RJ45 & RJ21 Wire Sequence

·RJ45 Wire Sequence

Both DAG2000-24S/32S and DAG2500-48S/64S/72S have RJ21 interface as FXS port.

One RJ21 cable has 25 pairs of wires, with the 25th pair of wires vacant. That means

one RJ21 interface outputs 24 calls.

DAG3000-112S is equipped with RJ45 interface as FXS port. One RJ45 cable can output

four calls.The internal wire sequence of RJ45 cable is shown as follows:

·RJ21 Wire Sequence

Call No.

Colour

PIN No.

White

Blue

P26

1 2 34

White Orange White Green White Brown White Slate

P27 P3 P28 P4 P29 P5 P30

Call No.

Colour

PIN No.

Red

Blue

P31

68 9

Orange Green Brown Slate

P7 P32

P33 P9

P34

P10

P35

Red Red Red Red

Call No.

Colour

PIN No.

Black

P11

Blue

P36

11 12 13 14

Orange Green Brown Slate

P12 P37 P13 P38 P14

P39

P15

P40

Black Black Black Black

Call No.

Colour

PIN No.

Yellow

P16

Blue

P41

16 17 18 19

Orange Green Brown Slate

P17

P42

P18

P43 P19 P44 P20 P45

Yellow Yellow Yellow Yellow

Call No.

23 24

Colour Violet Blue Orange Green Brown Slate

Violet Violet Violet Violet

PIN No.

P21

P46

P22

P47 P23 P48 P24 P49 P25

P50

Pair 1

Pair 2

Pair 3

Pair 4

Orange & White

Orange

Green & White

Green

Blue& White

Blue

Brown & White

Brown

Modify PC’s IP Address

To log in the Web Management System of the gateway, you need to modify the IP address

of PC first to make it at the same network segment with the gateway.

On the PC, click ‘Network (or Ethernet) → Properties’.

Double-click ‘Internet Protocol Version 4 (TCP/IPv4)’.

Select ‘Use the following IP address’, and then enter an available IP address

‘192.168.11.XXX’ which is at the same network segment with ‘192.168.11.1’.

Open a web browser and enter the gateway’s IP address (default IP is 192.168.11.1).

Then input username and password in the displayed login GUI. Both the default

username and password are admin.。

Autres manuels pour DAG2000-16S

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Dinstar Porte

Dinstar

Dinstar DAG1000-4O Manuel utilisateur

Dinstar

Dinstar UC2000 Manuel utilisateur

Dinstar

Dinstar DAG1000-1S Manuel utilisateur

Dinstar

Dinstar DAG1000-4S Manuel utilisateur

Dinstar

Dinstar UC100-1G1S1O Manuel utilisateur

Dinstar

Dinstar UC100-1V1S1O Manuel utilisateur

Dinstar

Dinstar DAG1000 Series Manuel utilisateur

Dinstar

Dinstar MTG3000 Manuel utilisateur

Dinstar

Dinstar DWG2000E Manuel utilisateur

Dinstar

Dinstar DAG3000-112S Manuel utilisateur

Dinstar

Dinstar DAG2000-16S Manuel utilisateur

Dinstar

Dinstar DWG2000-1G Manuel utilisateur

Dinstar

Dinstar MTG2000B Manuel utilisateur

Dinstar

Dinstar UC2000-VE Manuel utilisateur

Dinstar

Dinstar DWG2000-1G Manuel utilisateur

Dinstar

Dinstar MTG1000 Manuel utilisateur

Dinstar

Dinstar DAG3000-24O Manuel utilisateur

Dinstar

Dinstar MMTG200 Manuel utilisateur

Dinstar

Dinstar MTG200 Manuel utilisateur

Dinstar

Dinstar MTG2000B Manuel utilisateur

Dinstar

Dinstar MTG5000-64E1 Manuel utilisateur

Dinstar

Dinstar MTG1000 Manuel utilisateur

Dinstar

Dinstar DAG3000-32S Manuel utilisateur

Dinstar

Dinstar DAG2000-16S Manuel utilisateur

Manuels Porte populaires d'autres marques

LST

LST M500RFE-AS Manuel utilisateur

Kinnex

Kinnex Media Gateway Manuel utilisateur

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur

Telsey

Telsey CPVA 500 - SIP Manuel utilisateur

RTA

RTA 460A-NNA4 Fiche technique

Shaw

Shaw Gateway HDPVR Manuel utilisateur

ABB

ABB VSN900 Guide de démarrage rapide

Commander

Commander Pulse Manuel utilisateur

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuel utilisateur

NETGEAR

NETGEAR C6300BD Manuel utilisateur

Amit

Amit CDW531AM Manuel utilisateur

HMS

HMS Netbiter EasyConnect EC150 Manuel utilisateur

Huawei

Huawei EchoLife HG620 Manuel utilisateur

AT&T

AT&T U-verse 3801 Manuel d'utilisation et d'entretien

Logic IO

Logic IO RTCU MX2 turbo Manuel utilisateur

Suttle

Suttle MediaMAX MXM-521 Manuel utilisateur