Digitus DS-55400 Manuel utilisateur
HDMI VIDEO EXTENDER
User Manual
DS-55400
１
Table of Contents
1.0 Introduction........................................................................... 2
2.0 Specifications ....................................................................... 3
3.0 Package Contents ................................................................ 3
4.0 Panel Descriptions ............................................................... 4
5.0 Connection and operation................................................... 7
２
Dear customer
Thank you for purchasing this product. For optimum performance and safety,
please read these instructions carefully before connecting, operating or
adjusting this product. Please keep this manual for future reference.
1.0 INTRODUCTION
The Extender is based on the HDBaseT technology. It extends your HD display
with the resolutions of 1080p/60Hz up to 330 feet (100 meters) away from your
HDMI or DVI-D source using one CAT5e/6 cable. Built-in IR extender function
allows IR remote control of Source devices from remote viewing location by
sending IR commands received in the vicinity of the Display back to the Source
devices.
It also provides POE function that you only need to provide a piece of 48V/1A
DC power adapter at the end of the Sender to supply the power both the end of
the Sender and Receiver.
1.1 FEATURES
Support HDCP
Support POE
Support uncompressed HDMI signal.
Enables HDMI 10.2Gbps over a single 100m Cat5e/6 cable.
Support 340MHz/3.4Gbps per channel (10.2Gbps all channel) bandwidth.
Support 1080p@60Hz@48bit pixels
Support 3D pass-through.
Support CEC pass-through.
Support uncompressed audio such as LPCM.
Support compressed audio such as DTS Digital, Dolby Digital（including
DTS-HD and Dolby True HD）.
Built-in IR extender function allows IR remote control of Source devices from
remote viewing location by sending IR commands received in the vicinity of
the Display back to the Source devices.
CAT5e/6 cable follows the standard of IEEE-568B.
３
2.0 SPECIFICATIONS
Signal Inputs/Output
Input Video Signal 1.2 volts p-p
Output Video HDMI
Video format supported
DTV/HDTV 480i/576i/480p/576p/720p/1080i/1080P
Transmission distance
Cat5e/6 cable 100m for1080p/60Hz
Operating Frequency
Video Amplifier Bandwidth 3.4Gpbs/340MHz
Vertical Frequency Range 50/60Hz
Resolutions(HDTV)
Interlaced(50&60Hz) 480i,576i,1080i
Progressive(50&60Hz) 480p,576p,720p,1080p
Mechanical
Size (L-W-H) 100×65×25.5MM
Weight (Net) 170G（each unit）
Warranty
Limited Warranty 1 Year Parts and Labor
Power Requirement
Power Supply 48V DC@1A
Power consumption (Max) 16.8W
Regulatory Approvals
Converter Unit FCC,CE,UL
Power Supply UL,CE,FCC
Accessories
AC Power Adapter US standard, UK standard and so on
User Manual English Version
3.0 PACKAGE CONTENTS
Before attempting to use this unit, please check the packaging and make sure
the following items are contained in the shipping carton:
1) Main unit NO. 1 Sender
2) Main unit NO. 2 Receiver
3) One piece of 48V DC Power Supply.
4) IR(Extender infrared receiver) X1
5) IE(Extender infrared emitter) X1
6) User’s Manual
４
4.0 PANEL DESCRIPTIONS
Sender
(1) DC/48V
(2) Power Indicator
The LED will turn on once the DC/48V provided.
(3) Link
When LED is “ON”, it indicates HDBaseT link connection established
between the Sender and the Receiver over the Cat5e/6 cable.
５
(4) HDCP
When the LED is “ON”, it indicates a video content with HDCP protection is
being transferred.
When LED is “Blinking”, it indicates a video content without HDCP.
When LED is “OFF”, it indicates no video connected.
(5) HDBaseT
Connect the Sender to the Receiver using a Cat5e/6 cable.
(6) IE
Connect Extender infrared emitter cable from this port to the HDMI Source
to control the source from the viewing location.
(7) HDMI In
Connect HDMI Source to this Port.
Receiver
６
(2) Power Indicator
The LED will turn on once the 48V Power adapter provided at the end of the
Sender.
(3) Link
When LED is “ON”, it indicates HDBaseT link connection established
between the Sender and the Receiver over the Cat5e/6 cable.
(4) HDCP
When the LED is “ON”, it indicates a video content with HDCP protection is
being transferred.
When LED is “Blinking”, it indicates a video content without HDCP.
When LED is “OFF”, it indicates no video connected.
(5) HDBaseT
Connect the Sender to the Receiver using a Cat5e/6 cable.
(6) IR
Connect Extender infrared receiver cable from this port to receiver the IR
command of the source
(7) HDMI Out
Connect HDMI Sink to this Port
７
5.0 CONNECTION AND OPERATION
1) Connect the HDMI source (such as DVD, PS3, STB ) to the input of
Sender.
2) Connect the output of Receiver to HDTV display.
3) Use a Cat5e/6 cable up to 100m to connect the Sender and Receiver.
4) Plug one piece of 48V/1A power supply into the Sender
5) Power on the HDTV display and HDMI source.
Note: It is recommended to use one continuous run Cat5e/6 cable from one
end to the other. In some cases, connecting through a patch connector might
not work.
Attention: Insert / Extract cable gently.
5.1 CONNECTION DIAGRAM
Table des matières
Autres manuels Digitus Extenseur
Digitus
Digitus DS-55122 Manuel utilisateur
Digitus
Digitus DS-55529 Manuel utilisateur
Digitus
Digitus DS-55302 Manuel utilisateur
Digitus
Digitus DN-95127-1 Manuel utilisateur
Digitus
Digitus DA-70139-2 Manuel utilisateur
Digitus
Digitus DN-95129 Manuel utilisateur
Digitus
Digitus DS-55316 Manuel utilisateur
Digitus
Digitus DN-95126 Manuel utilisateur
Digitus
Digitus DS-51201 Manuel utilisateur
Digitus
Digitus DS-55203 Manuel utilisateur
Digitus
Digitus DS-54901 Manuel utilisateur
Digitus
Digitus DS-55500 Manuel utilisateur
Digitus
Digitus DS-55321 Manuel utilisateur
Digitus
Digitus DA-70143 Manuel utilisateur
Digitus
Digitus DC-53101 Manuel utilisateur
Digitus
Digitus DS-55501 Manuel utilisateur
Digitus
Digitus DS-55506 Manuel utilisateur
Digitus
Digitus DS-55204 Manuel utilisateur
Digitus
Digitus DC-56100 Manuel utilisateur
Digitus
Digitus DS-55100-1 Manuel utilisateur
