Digi TransPort WR21 Manuel utilisateur

Quick Start Guide

TransPort® WR21

Welcome to your Digi product

Get started: This guide helps you with initial product setup. Need more? Find additional

product support at www.digi.com/support/TransPortWR21. Or connect to the online

documentation by scanning this code:

Digi Technical Support: Digi offers multiple support plans to help you get the most out of your

product. For information on Technical Support plans and pricing, contact us at 877.912.3444 or

visit www.digi.com/support.

Documentation Feedback: To provide feedback on this documentation, send your comments

to techcomm@digi.com.

1Verify your components

Optional provided equipment Required additional equipment

Your box may contain additional cables or antennas, based on your

model and configuration options.

Verify that you have all included equipment. If any item is missing or damaged, contact your supplier.

2Connect the hardware

1. Insert the SIM card(s) into the SIMsockets. For SIM 1, the contacts must be face

down.

For SIM 2, the contacts must be face up. Insert the SIM cards with the chamfered

corner first.

2. Connect the cellular antenna to the WWAN PRIMARY connector on the unit. If the

unit is equipped with a secondary cellular antenna connector, connect it to the

WWANSECONDARY connector.

3. Connect one end of the Ethernet cable to the LAN 0 port on the unit and the

other end to a LANport on a PC.

4. Connect the power supply. Depending on model, the unit either comes with an AC

power supply or DC power cord with one of the following plug types.

Barrel plug-type variants: Connect the barrel plug end of the power supply to

the power connector on the unit, and plug the other end into a wall outlet.

nThe barrel plug end of the power supply has a twist-lock connector. Once

you have plugged in the connector, rotate it 90 degrees to secure it in place.

nInternational units come with interchangeable power supply adapters.

Digi, Digi International, and the Digi logo are trademarks or registered trademarks in the United States and other countries worldwide. All other trademarks mentioned in this

document are the property of their respective owners.

Terminal block variants: Remove the pluggable connector from the unit and screw down a proper power source to its terminals.

Next, reconnect the pluggable connector to the unit, following the pin-out diagram below.

5. When the unit is powered-up, the POWER LED illuminates and the unit initiates a series of diagnostic self-tests. During this process one or

more of the other indicators flashes to show that the unit is busy. When the flashing stops, the unit has completed its self-test diagnostic

and is ready to be configured.

Note Position the Digi TransPort WR21 on a flat, level surface or via wall-mount, rackmount, or DIN rail mounting brackets in a location with

adequate ventilation. The unit is designed for indoor use. Do not expose the unit to extreme heat or cold, strong magnetic fields, or liquids.

3Run the Getting Started Wizard

If your PC is configured to automatically get an IP address, it can obtain the IP address from the TransPort WR21. Otherwise, make sure your

PCcan connect to the network 192.168.1.0 (255.255.255.0).

1. Enter 192.168.1.1 into the address bar of the web browser.

2. The first page of the Getting Started Wizard appears. This wizard guides you through initial configuration for your TransPort device.

nTo run the wizard, click Get Started.

nTo manually configure the TransPort device, click Skip Wizard.

Note The default username and password for logging in to the TransPort device are username and password.

4View the TransPort LEDs and startup states

nPOWER LED:

Off: No power

Green:TransPort device is powered

nn SERVICE LED:

Off: No WWAN network connection

Green: Connected to WWAN network

Flashing: WWAN traffic is being transmitted or received

nWWAN LED: Indicates the presence and level of cellular service running on the device.

Off: No cellular service

1 Blink: GPRS mode

2 Blinks: EDGE mode

3 Blinks: UMTS mode

4 Blinks: HSDPA mode

5 Blinks: HSUPA mode

6 Blinks: LTE mode

nSIGNAL LEDs: Indicate the strength of the cellular signal.

3 LEDs: Excellent

2 LEDs: Good

1 LED: Fair

0 LEDs: Poor or no signal

After the Getting Started Wizard completes, the TransPort web interface appears. For additional configuration, use the web interface and refer

to the Digi TransPort User Guide and Application Notes on the Digi website at www.digi.com/support/TransPortWR21.

Autres manuels pour TransPort WR21

Table des matières

Autres manuels Digi Routeur réseau

Digi

Digi XPressWireless Manuel utilisateur

Digi

Digi TransPort WR31 Manuel utilisateur

Digi

Digi TransPort WR11 Manuel utilisateur

Digi

Digi IX10 Manuel utilisateur

Digi

Digi TX64 Manuel utilisateur

Digi

Digi IX10-00G4 Manuel utilisateur

Digi

Digi Connect Series Guide de l'utilisateur

Digi

Digi WR44v1 Manuel utilisateur

Digi

Digi TransPort WR64 Manuel utilisateur

Digi

Digi AnywhereUSB Series Manuel utilisateur

Digi

Digi IX10 Manuel utilisateur

Digi

Digi 6310-DX Manuel utilisateur

Digi

Digi TransPort WR11 XT Manuel utilisateur

Digi

Digi ConnectPort X2e ZB Manuel utilisateur

Digi

Digi 6350-SR Manuel utilisateur

Digi

Digi TransPort WR41 Manuel utilisateur

Digi

Digi TransPort WR41 Manuel utilisateur

Digi

Digi 6330-MX Manuel utilisateur

Digi

Digi IR4420 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Digi

Digi TX64 Manuel utilisateur

Digi

Digi XPress Manuel utilisateur

Digi

Digi TransPort WR21 Manuel utilisateur

Digi

Digi TransPort WR11 Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité

LevelOne

LevelOne FBR-1416 Manuel utilisateur