DFI MB331-CRM Manuel utilisateur

MB331-CRM

System Board

User’s Manual

A20810433

This publication contains information that is protected by copyright. No part of it

may be reproduced in any form or by any means or used to make any transforma-

tion/adaptation without the prior written permission from the copyright holders.

This publication is provided for informational purposes only. The manufacturer

makes no representations or warranties with respect to the contents or use of this

manual and specifically disclaims any express or implied warranties of merchant-

ability or fitness for any particular purpose. The user will assume the entire risk of

the use or the results of the use of this document. Further, the manufacturer re-

serves the right to revise this publication and make changes to its contents at any

time, without obligation to notify any person or entity of such revisions or changes.

Changes after the publication’s first release will be based on the product’s revision.

The website will always provide the most updated information.

Trademarks

All trademarks and registered trademarks of products appearing in this manual

are the properties of their respective holders.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment

is operated in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or televi-

sion reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio TV technician for help.

Notice:

1. The changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

2. Shielded interface cables must be used in order to comply with the emission

limits.

Introduction

Table of Contents

Trademarks........................................................................................2

FCC and DOC Statement on Class B..............................................3

About this Manual .............................................................................6

Warranty ..........................................................................................6

Static Electricity Precautions.............................................................7

Safety Measures.................................................................................7

About the Package ............................................................................8

Before Using the System Board........................................................8

Chapter 1 - Introduction ..................................................................9

Specifications..................................................................................9

Features ...................................................................................... 12

Chapter 2 - Hardware Installation.................................................. 15

System Board Layout .................................................................... 15

System Memory ........................................................................... 16

Installing the DIMM Module....................................................... 18

CPU ............................................................................................ 20

Installing the CPU .................................................................... 21

Installing the Fan and Heat Sink................................................ 24

Jumper Settings............................................................................. 27

Clear CMOS Data ..................................................................... 27

PS/2 Power Select.................................................................... 28

USB Power Select..................................................................... 29

Power-on Select....................................................................... 30

COM1/COM2 RS232/RS422/RS485 Select.................................... 31

COM1/COM2 RS232/Power Select............................................... 32

Rear Panel I/O Ports..................................................................... 33

PS/2 Mouse and PS/2 Keyboard Ports......................................... 34

COM (Serial) Ports ................................................................... 35

VGA Port................................................................................. 36

DVI-I Port ............................................................................... 37

RJ45 LAN Ports........................................................................ 38

USB Ports................................................................................ 39

Audio...................................................................................... 41

Introduction

I/O Connectors............................................................................ 43

Digital I/O Connectors .............................................................. 44

SATA (Serial ATA) Connectors .................................................... 45

Cooling Fan Connectors............................................................. 46

Chassis Instrusion Connector .................................................... 47

Power Connectors .................................................................... 48

Standby Power LED .................................................................. 49

Front Panel Connectors ............................................................. 50

Expansion Slots ....................................................................... 51

Battery ................................................................................... 52

Chapter 3 - BIOS Setup.................................................................. 53

Overview ..............................................................................................................53

AMI BIOS Setup Utility ................................................................. 55

Main ....................................................................................... 55

Advanced ................................................................................ 56

Chipset ................................................................................... 74

Boot ....................................................................................... 80

Security .................................................................................. 82

Save & Exit ............................................................................. 84

Updating the BIOS........................................................................ 85

Chapter 4 - Supported Software ................................................... 86

Chapter 5 - RAID ........................................................................ 115

RAID Levels .......................................................................................................115

Settings................................................................................................................116

Chapter 6 - Intel AMT Settings ................................................... 120

Overview ............................................................................................................120

Enable Intel®AMT in the AMI BIOS ............................................................121

Enable Intel®AMT in the Intel®Management Engine BIOS

Extension (MEBX) Screen ..............................................................................123

Appendix A - NLITE and AHCI Installation Guide ....................... 148

Appendix B - Watchdog Sample Code ......................................... 160

Appendix C - System Error Message............................................ 161

Appendix D - Troubleshooting...................................................... 163

Introduction

About this Manual

An electronic file of this manual is included in the CD. To view the user’s manual

in the CD, insert the CD into a CD-ROM drive. The autorun screen (Main Board

Utility CD) will appear. Click “User’s Manual” on the main menu.

Warranty

1. Warranty does not cover damages or failures that arised from misuse of the

product, inability to use the product, unauthorized replacement or alteration

of components and product specifications.

2. The warranty is void if the product has been subjected to physical abuse,

improper installation, modification, accidents or unauthorized repair of the

product.

3. Unless otherwise instructed in this user’s manual, the user may not, under

any circumstances, attempt to perform service, adjustments or repairs on the

product, whether in or out of warranty. It must be returned to the purchase

point, factory or authorized service agency for all such work.

4. We will not be liable for any indirect, special, incidental or consequencial

damages to the product that has been modified or altered.

Introduction

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board, components

or devices even before installing them in your system unit. Static electrical dis-

charge can damage computer components without causing any signs of physical

damage. You must take extra care in handling them to ensure against electro-

static build-up.

1. To prevent electrostatic build-up, leave the system board in its anti-static bag

until you are ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of the compo-

nents, contacts or connections.

5. Avoid touching the pins or contacts on all modules and connectors. Hold

modules or connectors by their ends.

Important:

Electrostatic discharge (ESD) can damage your processor, disk drive and

other components. Perform the upgrade instruction procedures described

at an ESD workstation only. If such a station is not available, you can

provide some ESD protection by wearing an antistatic wrist strap and

attaching it to a metal part of the system chassis. If a wrist strap is

unavailable, establish and maintain contact with the system chassis

throughout any procedures requiring ESD protection.

Safety Measures

To avoid damage to the system:

• Use the correct AC input voltage range.

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis cover for instal-

lation or servicing. After installation or servicing, cover the system chassis

before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend by the manufac-

turer.

• Dispose of used batteries according to local ordinance.

Introduction

About the Package

The system board package contains the following items. If any of these items are

missing or damaged, please contact your dealer or sales representative for as-

sistance.

One MB331-CRM motherboard

Two Serial ATA data cables

Two USB port cables (with bracket)

Two COM port cables (with bracket)

One I/O shield

One DVD

One QR (Quick Reference)

Optional Items

USB port cable

COM port cable

Serial ATA power cable

Serial ATA data cable

I/O shield

The system board and accessories in the package may not come similar to the

information listed above. This may differ in accordance to the sales region or

models in which it was sold. For more information about the standard package in

your region, please contact your dealer or sales representative.

Before Using the System Board

Before using the system board, prepare basic system components.

If you are installing the system board in a new system, you will need at least the

following internal components.

• A CPU

• Memory module

• Storage devices such as hard disk drive, CD-ROM, etc.

You will also need external system peripherals you intend to use which will nor-

mally include at least a keyboard, a mouse and a video display monitor.

Introduction

Processor

Chipset

System Memory

Expansion Slots

Graphics

Audio

LAN

Chapter 1 - Introduction

• LGA 1155 socket for:

- 3rd generation Intel®CoreTM processors

(22nm process technology)

: Intel®CoreTM i7-3770 (8M Cache, up to 3.9GHz); 77W

: Intel®CoreTM i5-3550S (6M Cache, up to 3.7GHz); 65W

: Intel®CoreTM i3-3220 (3M Cache, 3.3GHz); 55W

: Intel®Pentium®G2120 (3M Cache, 3.1 GHz); 65W

- 2nd generation Intel®CoreTM processors

(32nm process technology)

: Intel®CoreTM i7-2600 (8M Cache, up to 3.8 GHz); 95W

: Intel®CoreTM i5-2400 (6M Cache, up to 3.4 GHz); 95W

: Intel®CoreTM i3-2120 (3M Cache, 3.3 GHz); 65W

: Intel®Pentium®G850 (3M Cache, 2.9 GHz); 65W

• Intel®Q77 Express chipset

• Four 240-pin DDR3 DIMM sockets

• Supports DDR3 1333/1600MHz (3rd generation processors)

Supports DDR3 1066/1333MHz (2nd generation processors)

• Supports dual channel memory interface

• Supports up to 32GB system memory

• DRAM device technologies: 1Gb, 2Gb and 4Gb DDR3 DRAM

technologies are supported for x8 and x16 devices, unbuf-

fered, non-ECC

• 1 PCIe x16 slot

- Supports Gen 3.0 (3rd generation processors)

- Supports Gen 2.0 (2nd generation processors)

• 1 PCIe x4 slot (PCIe 2.0)

• 2 PCI slots (PCI 2.3)

• Intel®HD Graphics 4000 (i7); HD Graphics 2500 (i5/i3/

Pentium)

• Display ports: DVI-I (DVI-D signal) and VGA

• DVI: resolution up to 1920x1200 @60Hz

• VGA: resolution up to 2048x1536 @75Hz, 32-bit

• Intel®Clear Video Technology

• Intel®Advanced Vector Extensions (Intel®AVX) Instructions

• Supports DirectX 11 and OGL 3.0

• Realtek ALC886 5.1-channel High Deﬁnition Audio

• Audio outputs: Mic-in/Center+Subwoofer, Lne-in/Surround and

Line-out

• S/PDIF audio interface

• Intel®WG82579LM with iAMT8.0 Gigabit Ethernet Phy

• Realtek RTL8111DL PCI Express Gigabit Ethernet controller

• Integrated 10/100/1000 transceiver

• Fully compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab

Specifications

Introduction

• 6 Serial ATA ports

- 2 SATA 3.0 ports with data transfer rate up to 6Gb/s

- 4 SATA 2.0 ports with data transfer rate up to 3Gb/s

(SATA port 4 provides adequate space for SATA DOM)

• Integrated Advanced Host Controller Interface (AHCI) con-

troller

• Supports RAID 0/1/5/10

• Supports iAMT8.0

• Out-of-band system access

• Remote troubleshooting and recovery

• Hardware-based agent presence checking

• Proactive alerting

• Remote hardware and software asset tracking

• Provides a Trusted PC for secure transactions

• Provides software license protection, enforcement and

password protection

• XHCI Host Controller supports up to 4 super speed USB

3.0 ports

• 1 mini-DIN-6 PS/2 mouse port

• 1 mini-DIN-6 PS/2 keyboard port

• 2 DB-9 serial ports

- Supports RS232/422/485 (RS232 and/or Power)

• 1 DB-15 VGA port

• 1 DVI-I port (DVI-D signal)

• 2 RJ45 LAN ports

• 4 USB 3.0 ports

• Line-in/surround, Line out, and Mic-in/Center+Subwoofer

jacks

• 3 connectors for 6 external USB 2.0 ports

• 4 connectors for 4 external RS232 serial ports (2.54mm

pitch)

• 1 8-bit Digital I/O connector

• 1 front audio connector for line-out and mic-in jacks

• 1 S/PDIF connector

• 6 Serial ATA ports (2 SATA 3.0; 4 SATA 2.0)

• 1 24-pin ATX power connector

• 1 8-pin 12V power connector

• 1 chassis intrusion connector

• 1 front panel connector

• 3 fan connectors

Serial ATA

Intel Active

Management

Technology

(AMT)

TPM (optional)

USB Interface

Rear Panel I/O

Ports

I/O Connectors

Autres manuels pour MB331-CRM

Table des matières

Autres manuels DFI Carte mère

DFI

DFI SU171 Manuel utilisateur

DFI

DFI G486-EVB Manuel utilisateur

DFI

DFI AZ30-TC Manuel utilisateur

DFI

DFI P4X533-ALE Manuel utilisateur

DFI

DFI CS632-C246 Manuel utilisateur

DFI

DFI LANParty UT ICFX3200-T2R/G Manuel utilisateur

DFI

DFI CA64-EC Manuel utilisateur

DFI

DFI CMS311-W480E/Q470E Manuel utilisateur

DFI

DFI NS30-TC Manuel utilisateur

DFI

DFI G5C900-B Manuel utilisateur

DFI

DFI WL051-BCC-4305UE Manuel utilisateur

DFI

DFI ADN171 Manuel utilisateur

DFI

DFI CS330 Manuel utilisateur

DFI

DFI KD631-C236 Manuel utilisateur

DFI

DFI K6BV3+ Manuel utilisateur

DFI

DFI LanParty NFII Ultra B Manuel utilisateur

DFI

DFI G586IPV Manuel utilisateur

DFI

DFI ADS630 Manuel utilisateur

DFI

DFI P2MEX/A Manuel utilisateur

DFI

DFI NP100-N16C Manuel utilisateur

DFI

DFI CS170-Q370 Manuel utilisateur

DFI

DFI ADS310-R680E/Q670E Manuel utilisateur

DFI

DFI SB331-D Manuel utilisateur

DFI

DFI G486VPC Manuel utilisateur

Manuels Carte mère populaires d'autres marques

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuel utilisateur