DFI CA64-EC Manuel utilisateur
CA64-EC
Rev. A+
System Board Users Manual
Carte Mère Manuel Pour Utilisateur
System-Platine Benutzerhandbuch
Tablero Electrónico del Sistema Manual del Usuario
45100039
Copyright
This publication contains information that is protected by copyright.
No part of it may be reproduced in any form or by any means or
used to make any transformation/adaptation without the prior
written permission from the copyright holders.
This publication is provided for informational purposes only. The
manufacturer makes no representations or warranties with respect to
the contents or use of this manual and specifically disclaims any
express or implied warranties of merchantability or fitness for any
particular purpose.The user will assume the entire risk of the use or
the results of the use of this document. Further, the manufacturer
reserves the right to revise this publication and make changes to its
contents at any time, without obligation to notify any person or
entity of such revisions or changes.
© 2000. All Rights Reserved.
Trademarks
Microsoft®MS-DOS®, WindowsTM, Windows®95, Windows®98,
Windows®98 SE, Windows®2000 and Windows NT®4.0 are
registered trademarks of Microsoft Corporation. Intel®, Pentium®III
and CeleronTM are registered trademarks of Intel Corporation. VIA
CyrixIII is a registered trademark of VIA Technologies, Inc. Award is a
registered trademark of Award Software, Inc. Other trademarks and
registered trademarks of products appearing in this manual are the
properties of their respective holders.
Caution:
Danger of explosion if battery incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer.
Dispose of used batteries according to the battery manufacturers
instructions.
FCC and DOC Statement on Class B
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio TV technician for
help.
Notice:
1. The changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority
to operate the equipment.
2. Shielded interface cables must be used in order to comply with
the emission limits.
4
Quick Setup Guide
1
Quick Setup
Guide
Table of Contents
Chapter 1
Quick Setup Guide.............................................
Chapter 2
English......................................................................
Chapter 3
Français (French).................................................
Chapter 4
Deutsch (German)................................................
Chapter 5
Español (Spanish)..................................................
5
23
39
57
75
5
1
Quick Setup Guide
Quick Setup
Guide
Chapter 1 - Quick Setup Guide
Table of Contents
1.1 System Board Layout..................................................................................................
1.2 Jumpers.....................................................................................................................................
1.3 Ports and Connectors................................................................................................
1.4 Award BIOS Setup Utility.......................................................................................
6
7
10
18
6
Quick Setup Guide
1
Quick Setup
Guide
1.1 System Board Layout
7
1
Quick Setup Guide
Quick Setup
Guide
1.2 Jumpers
1.2.1 Frequency Ratio Settings - SW1
Black rectangle
denotes the part
that is protruding,
the adjustable
switch.
Important:
The frequency ratio of some processors shown in the table may
have been locked by the manufacturer. If you are using this kind
of processor, setting an extended ratio for the processor will have
no effect. The system will instead use its factory default ratio.
The frequency ratio of processors greater than 8x has been
locked by the manufacturer and will no longer have the flexibility
of using extended ratios. Therefore, the system will use the
processors factory default ratio.
--- --- 4x
--- 4.5x
333MHz 5x
Processor SW1
66MHz 100MHz
Freq.
Ratio
5.5x
Processor SW1
66MHz 100MHz
Freq.
Ratio
400MHz
433MHz
466MHz
500MHz
6x
6.5x
7x
7.5x
8x533MHz
500MHz
366MHz
133MHz
533MHz
133MHz
650MHz
700MHz 933MHz
866MHz
800MHz
750MHz 1GHz
800MHz 1.067GHz*
667MHz
733MHz
300MHz
300AMHz
550MHz
600MHz
600MHz
8
Quick Setup Guide
1
Quick Setup
Guide
At the time this document was printed, the CPU marked with
asterisk (*) is not yet available. It is included in the table for
reference only.
The processors supported by the system board support VID
(Voltage Identification). The switching voltage regulator on the
system board will automatically set the voltage regulator
according to the voltage of the processor.
1.2.2 CPUs Front Side Bus - JP2 and JP3
2-3 On
1-2 On All Off
1
2
3
1
2
3
1
2
3
Warning:
Some processors, when overclocked, may result to the processors or
systems instability and are not guaranteed to provide better system
performance. If you are unable to boot your system due to
overclocking, make sure to set these jumpers back to their default
settings.
JP2
1-2 On
2-3 On
All Off
All Off
JP3
1-2 On
2-3 On
2-3 On
All Off
Auto*
66MHz
100MHz
133MHz
* denotes default setting
9
1
Quick Setup Guide
Quick Setup
Guide
1.2.4 Onboard Audio Codec - JP7, JP8 and JP9
1.2.3 Clear CMOS Data - JP6
2-3 On:
Clear CMOS Data
1-2 On: Normal
(default)
1
2
3
1
2
3
2-3 On:
Disable the Onboard
Audio Codec
1-2 On:
Enable the Onboard
Audio Codec
(default)
1
2
3
JP7 JP9JP8
1
2
3
JP7 JP9JP8
10
Quick Setup Guide
1
Quick Setup
Guide
1.3 Ports and Connectors
1.3.1 PS/2 Mouse and PS/2 Keyboard Ports
Make sure to turn off your
computer prior to
connecting or disconnecting
a mouse or keyboard.
Failure to do so may
damage the system board.
PS/2 Mouse
PS/2 Keyboard
1.3.2 Parallel Port
Parallel Port
Table des matières
Autres manuels DFI Carte mère
DFI
DFI PR611-C621 Manuel utilisateur
DFI
DFI COM331-B Manuel utilisateur
DFI
DFI CP900-B Manuel utilisateur
DFI
DFI EHL556 Manuel utilisateur
DFI
DFI G586SPB AIO Manuel utilisateur
DFI
DFI K6XV3+/66 Manuel utilisateur
DFI
DFI CA33-SC Manuel utilisateur
DFI
DFI PB64-BX Manuel utilisateur
DFI
DFI G4E620-N Manuel utilisateur
DFI
DFI LanParty UT CFX3200-DR Manuel utilisateur
DFI
DFI OT951-D Series Manuel utilisateur
DFI
DFI AD76 RAID Manuel utilisateur
DFI
DFI LanParty LT P35 Manuel utilisateur
DFI
DFI KD631-C236 Manuel utilisateur
DFI
DFI Blood-Iron LanParty Bi 785G-M35 Manuel utilisateur
DFI
DFI SO630 Manuel utilisateur
DFI
DFI HD330 Manuel utilisateur
DFI
DFI ST2K Series Manuel utilisateur
DFI
DFI CB64-BX Manuel utilisateur
DFI
DFI PL610-C622 Manuel utilisateur
Manuels Carte mère populaires d'autres marques
Gigabyte
Gigabyte GA-9IVDT Manuel utilisateur
Texas Instruments
Texas Instruments ADS8372EVM Manuel utilisateur
Commell
Commell MS-C73 Manuel utilisateur
IBT Technologies
IBT Technologies MB860 Manuel utilisateur
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur
Biostar
Biostar M7VIT Bravo Instructions d'utilisation et d'installation
