DFI NS30-TC Manuel utilisateur

NS30-TC

NS30-TL

Rev. A+

System Board

User’s Manual

60700225

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior

written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose. The user will assume the entire risk of the use or

the results of the use of this document. Further, the manufacturer

reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or

entity of such revisions or changes.

Trademarks

Windows® 98, Windows® 98 SE, Windows® ME, Windows® 000,

Windows NT® 4.0 and Windows® XP are registered trademarks of

Microsoft Corporation. Intel® and Pentium® 4 are registered

trademarks of Intel Corporation. SiS® is a registered trademark of

Silicon Integrated Systems Corporation. Award is a registered

trademark of Award Software, Inc. Other trademarks and registered

trademarks of products appearing in this manual are the properties

of their respective holders.

Caution

To avoid damage to the system:

• Use the correct AC input voltage range.

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or ser vicing,

cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend by

the manufacturer.

• Dispose of used batteries according to the battery

manufacturer’s instructions.

Joystick or MIDI port:

• Do not use any joystick or MIDI device that requires more than

10A current at 5V DC . There is a risk of fire for devices that

exceed this limit.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to tr y to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

. Shielded interface cables must be used in order to comply with

the emission limits.

Notice

This user’s manual contains detailed information about the system

board. If, in some cases, some information doesn’t match those

shown in the multilingual manual, the multilingual manual should

always be regarded as the most updated version. The multilingual

manual is included in the system board package.

To view the user’s manual, insert the CD into a CD-ROM drive. The

autorun screen (Main Board Utility CD) will appear. Click “User’s

Manual”.

System Board

This user’s manual is for the NS30-TC and NS30-TL system boards.

The only difference between these boards is the NS30-TL system

board supports onboard LAN.

Table of Contents

Chapter 1 - Introduction

1.1 Features and Specifications..................................................................................

1. Package Checklist.........................................................................................................

Chapter 2 - Hardware Installation

.1 System Board Layout ..........................................................................................

. System Memory...........................................................................................................

.3 Jumper Settings for Clearing CMOS Data........................................

.4 Jumper Settings for Selecting the USB 5/6 Power......................

.5 Por ts and Connectors...........................................................................................

Chapter 3 - Award BIOS Setup Utility

3.1 The Basic Input/Output System.....................................................................

3.1.1 Standard CMOS Features.............................................................

3.1. Advanced BIOS Features..............................................................

3.1.3 Advanced Chipset Features ......................................................

3.1.4 Integrated Peripherals.........................................................................

3.1.5 Power Management Setup............................................................

3.1.6 PnP/PCI Configurations....................................................................

3.1.7 PC Health Status...................................................................................

3.1.8 Frequency/Voltage Control............................................................

3.1.9 Load Fail-Safe Defaults.....................................................................

3.1.10 Load Optimized Defaults..............................................................

3.1.11 Set Supervisor Password...............................................................

3.1.1 Set User Password..............................................................................

3.1.13 Save & Exit Setup.................................................................................

3.1.14 Exit Without Saving..............................................................................

3. Updating the BIOS.....................................................................................................

Introduction

105

Chapter 4 - Supported Softwares

4.1 Desktop Management Interface...................................................................

4.2 Drivers, Utilities and Software pplications.......................................

4.3 Installation Notes........................................................................................................

Appendix A - Using the Suspend to RAM

Function

.1 Using the Suspend to R M Function.....................................................

Appendix B - System Error Messages

B.1 POST Beep.....................................................................................................................

B.2 Error Messages.............................................................................................................

Appendix C - roubleshooting

C.1 Troubleshooting Checklist...................................................................................

100

101

107

Introduction

1.1 Features and Specifications

1.1.1 Features

Chipset

•SiS

® 645DX/96 L

Processor

The system board is equipped with Socket 478 for installing a

Pentium® 4 processor.

• Intel® Pentium® 4 processor (478-pin)

• Supports up to . GHz CPU speed

• 400/533MHz system data bus

System Memory

• Two 184-pin DDR DIMM sockets

• Supports 4 banks up to GB using PC1600 (DDR 00),

PC 100 (DDR 66) or PC 700 (DDR333) unbuffered DDR

SDRAM DIMM, .5V type

• 16Mb, 64Mb, 1 8Mb, 56Mb and 51 Mb SDRAM technology

with page size from KB up to 16KB

Chapter 1 - Introduction

Introduction

Expansion Slots

The system board is equipped with 1 universal AGP slot, 3 PCI

slots (1 shared with CNR slot) and 1 CNR slot.

AGP is an interface designed to support high performance 3D

graphics cards. It utilizes a dedicated pipeline to access system

memory for texturing, z-buffering and alpha blending. The universal

AGP slot supports AGP x with up to 533MB/sec. bandwidth and

AGP 4x with up to 1066MB/sec. bandwidth for 3D graphics

applications. AGP in this system board will deliver faster and better

graphics to your PC.

CNR (Communication and Networking Riser) is an interface that can

support multi-channel audio and V.90 analog modem.

Onboard Audio eatures

• AC'97 . extension compliant codec

• Supports Microsoft® DirectSound/DirectSound 3D

• AC’97 supported with full duplex, independent sample rate

converter for audio recording and playback

• S/PDIF-in/out interface

• 6-channel audio output

Onboard LAN eatures (NS30-TL only)

• Uses Phy fast ethernet controller

• Integrated IEEE 80 .3, 10BASE-T and 100BASE-TX compatible

PHY

• 3 -bit PCI master interface

• Integrated power management functions

• Full duplex support at both 10 and 100 Mbps

• Supports IEEE 80 .3u auto-negotiation

• Suppor ts wire for management

Introduction

ATX Double Deck Ports (PC 99 color-coded connectors)

• Four USB .0/1.1 por ts

• One RJ45 LAN port (NS30-TL only)

• Two NS16C550A-compatible DB-9 serial ports

• One DB- 5 parallel port

• One mini-DIN-6 PS/ mouse port

• One mini-DIN-6 PS/ keyboard por t

• Three audio jacks: line-out, line-in and mic-in

Connectors

• One connector for additional external USB .0/1.1 ports

• One connector for an external game/MIDI port

• One connector for external line-out and mic-in jacks

• Two internal audio connectors (AUX-in and CD-in)

• One S/PDIF-in connector

• One S/PDIF-out connector

• One connector for IrDA interface

• Two IDE connectors

• One floppy drive interface supports up to two .88MB floppy

drives

• Two ATX power supply connectors

• One Wake-On-LAN connector

• One Wake-On-Ring connector

• CPU fan and system fan connectors

PCI Bus Master IDE Controller

• Two PCI IDE interfaces support up to four IDE devices

• Supports ATA/33, ATA/66, ATA/100 and ATA/133 hard drives

• UDMA Modes 3, 4, 5 and 6 Enhanced IDE (data transfer rate

up to 133MB/sec.)

• Bus mastering reduces CPU utilization during disk transfer

• Supports ATAPI CD-ROM, LS-1 0 and ZIP

IrDA Interface

The system board is equipped with an IrDA connector for wireless

connectivity between your computer and peripheral devices.

Introduction

USB Ports

The system board supports 6 USB .0/1.1 ports. USB allows data

exchange between your computer and a wide range of

simultaneously accessible external Plug and Play peripherals.

BIOS

• Award BIOS, Windows® 98/ 000/ME/XP Plug and Play

compatible

• Supports SCSI sequential boot-up

• Flash EPROM for easy BIOS upgrades

• Supports DMI .0 function

• Mbit flash memory

Desktop Management Interface (DMI)

The system board comes with a DMI .0 built into the BIOS. The

DMI utility in the BIOS automatically records various information

about your system configuration and stores these information in the

DMI pool, which is a part of the system board's Plug and Play

BIOS. DMI, along with the appropriately networked software, is

designed to make inventory, maintenance and troubleshooting of

computer systems easier. Refer to chapter 4 for instructions on using

the DMI utility.

1.1.2 System Health Monitor Functions

The system board is capable of monitoring the following “system

health” conditions.

• Monitors CPU/system temperature and overheat alarm

• Monitors CPU/3.3V/5V/±1 V/VBAT/5VSB voltages and failure

alarm

• Monitors CPU/system fan speed and failure alarm

• Automatic system fan on/off control

• Read back capability that displays temperature, voltage and fan

speed

Refer to the “PC Health Status” section in chapter 3 and the

“Hardware Monitor” section in chapter 4 for more information.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels DFI Carte mère

DFI

DFI AM36-EC Manuel utilisateur

DFI

DFI EL620-C Manuel utilisateur

DFI

DFI LanParty 925X-T2 Manuel utilisateur

DFI

DFI SR100-N Manuel utilisateur

DFI

DFI ADS310-R680E/Q670E Manuel utilisateur

DFI

DFI G586IPV Manuel utilisateur

DFI

DFI Blood-Iron G41-T33 Manuel utilisateur

DFI

DFI GH551 Manuel utilisateur

DFI

DFI NP100-N16C Manuel utilisateur

DFI

DFI EHL171 Manuel utilisateur

DFI

DFI P2XBL D+ Manuel utilisateur

DFI

DFI RNO171 Manuel utilisateur

DFI

DFI AD72-SC Manuel utilisateur

DFI

DFI NS80-EA Manuel utilisateur

DFI

DFI PR810-C622 Manuel utilisateur

DFI

DFI KM266Pro-MLV Manuel utilisateur

DFI

DFI CM64-AL Manuel utilisateur

DFI

DFI NS80-EA Manuel utilisateur

DFI

DFI LanParty DK 790GX-M2RS Manuel utilisateur

DFI

DFI SD330 Manuel utilisateur

DFI

DFI NB30-EC Manuel utilisateur

DFI

DFI G586VPM/T Manuel utilisateur

DFI

DFI G486VPB Manuel utilisateur

DFI

DFI G7L330-B Manuel utilisateur

Manuels Carte mère populaires d'autres marques

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuel utilisateur