Danfoss WT-DR Manuel utilisateur

1 Installation Steps

The User Guide can be downloaded from: heating.danfoss.com.

1. Installation must be done by an authorised electrician.

2. The room thermostat should be installed at approx. 1.5 m

above floor and where the effects of sunlight, draught or oth-

er heat sources (eg. TV's) are avoided. See illustration 1.

3. First of all, carefully remove the cover. See illustration 2.

4. Connect the wire before mounting the back plate to the wall

box using the enclosed screws. Then mount the cover to the

back plate. See illustration 3.

2 Wiring

1. Dimensions (see ill. 4).

2. Wiring diagram (see ill. 5, S1, S2: floor sensor terminals; A1,

A2: volt-free auxiliary relay terminals, e.g. boiler).

3. WT-D/P is often used with Danfoss TWA actuator. Depending

on the conditions of power location and actuator type (NC or

NO), the wiring between room thermostat and actuator is dif-

ferent. Follow the illustrations to complete the wiring:

1. When power supply location is close to room thermo-

stat:

▪Connect to actuator TWA 230 V NC type (see ill. 6).

▪Connect to actuator TWA 230 V NO type (see ill. 7).

2. When power supply location is close to actuator:

▪Connect to actuator TWA 230 V NC type (see ill. 8).

▪Connect to actuator TWA 230 V NO type (see ill. 9).

3 Error Codes

Item Display Description

1 E1 room sensor failure

2 E2 floor sensor failure

4 Notes

1. Correct wiring is essential; using instrument to confirm L and

N before wiring is recommended.

2. Don't remove too much of the insulation cover from the wire

to avoid short circuit caused by the naked wire touching the

metal 86 size mounting wall box.

3. Don't let the screw press or touch the wire when using screw

to fix room thermostat in wall box. A short-circuit risk exists if

the wire insulation cover is damaged by the screw, and if the

naked wire connects with the screw.

4. If walls must be painted, mount the room thermostat after

painting, to avoid dust or paint material penetrating the

room thermostat and thus damaging the PCB.

5. The max load of relay is 3 A (resistive) or 1 A (inductive, such

as pump, motor). The relay will be damaged if the load ex-

ceeds the limit.

6. Don't cover the thermostat, for instance by hanging towels

directly in front of it.

7. The room thermostat should be connected to the corre-

sponding loop actuator in individual room temperature con-

trol.

5 Technical Specification

Feature Description

Approval CE Marking, EN60730

Ambient temperature -10 ℃ -60 ℃

IP class 30

Max load, inductive <1 A

Max load, resistive <3 A

Feature Description

Power consumption 2 W

Power supply 85-250 Vac, 50/60 Hz

Room temperature set range 5 ℃ -35 ℃

Floor temperature set range 20 ℃ -45 ℃

Shell material ABS + PC

Installation Guide

WT-DR/PR Installation Instruction

Danfoss Heating Solutions VICUK102 1

6 Illustrations

Illustration 1

Illustration 2

Illustration 3

Illustration 4

Illustration 5

Illustration 6

Illustration 7

Illustration 8

Illustration 9

Installation Guide WT-DR/PR Installation Instruction

VICUK102 Danfoss Heating Solutions

Installation Guide WT-DR/PR Installation Instruction

Danfoss Heating Solutions VICUK102 3

Installation Guide WT-DR/PR Installation Instruction

Danfoss A/S

Heating Solutions

Haarupvaenget 11

8600 Silkeborg

Denmark

Phone: +45 7488 8000

Fax: +45 7488 8100

Email: [email protected]

www.heating.danfoss.com

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products

already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective

VICUK102 Produced by Danfoss Heating Solutions © 07/2014

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Danfoss Thermostat

Danfoss

Danfoss FHV-R Manuel utilisateur

Danfoss

Danfoss C37 Manuel utilisateur

Danfoss

Danfoss ECL Comfort 310 Manuel utilisateur

Danfoss

Danfoss TS715 Si Instructions de montage

Danfoss

Danfoss DEVIreg 130 Manuel utilisateur

Danfoss

Danfoss DEVIreg 531 Manuel utilisateur

Danfoss

Danfoss TP5001 series Manuel utilisateur

Danfoss

Danfoss GreenCon RC-C2 Manuel utilisateur

Danfoss

Danfoss EFIT 550 Manuel utilisateur

Danfoss

Danfoss TP5000 si range Manuel utilisateur

Danfoss

Danfoss Icon Master Manuel utilisateur

Danfoss

Danfoss ECtemp 330 Manuel utilisateur

Danfoss

Danfoss TP4 Instructions de montage

Danfoss

Danfoss HC75-3 Manuel d'utilisation

Danfoss

Danfoss Link FT Manuel utilisateur

Danfoss

Danfoss LX205T Manuel utilisateur

Danfoss

Danfoss KP Series Manuel utilisateur

Danfoss

Danfoss ECL Comfort 310, A367 Manuel utilisateur

Danfoss

Danfoss TP7000 Series Manuel utilisateur

Danfoss

Danfoss ECtemp Smart Manuel utilisateur

Danfoss

Danfoss Living Eco Manuel utilisateur

Danfoss

Danfoss TPONE-RF Manuel utilisateur

Danfoss

Danfoss 088L5130 Manuel utilisateur

Danfoss

Danfoss TPOne-M Manuel utilisateur

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Honeywell

Honeywell CM721 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

Honeywell

Honeywell RLV4305 Manuel utilisateur

Honeywell

Honeywell Prestige 2.0 THX9421 Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur