Danfoss REP24CO1 Manuel utilisateur

REP24 CO1

GB Installation Instructions

User Instructions

Electronic Proportional Heat / Cool Thermostat

Index

INDEX

Installation Instructions 3-6

User Instructions 8

Please note

This product should only be installed by a suitably qualied

electrician or heating installer. The installation must comply

with local Building Regulations and wiring Regulations,

including any competent person requirements that may exist.

Installation Instructions

Specication

Thermostat features

Temperature Range 10-30°C

Thermostat Heat, Standby, Cool

Selector

Yes

Power Supply 24 Vac ± 15%, 50/60Hz

Fan Output 3 (1) A, 10-230Vac, Type 1B

Control Method P+I, 2k Proportional Band

Dimensions (mm) 110 wide x 90 high x 40 high

Design Standard EN60730-2-9

Rated Impulse Voltage 2.5Kv

Ball Hardness Test 75°C

Control Pollution Situation Degree 2

Temperature Accuracy ±1°C

Control Output 0-10 Vdc

Common Supply 10 - 230 Vac

Installation

First remove the wallplate from the back of the unit.

Fix at a height of approximately 1.5m from the oor, away

from draughts or heat sources such as fan-coil outlets,

sunlight or oce equipment.

Installation Instructions

Wiring

Product overview

This thermostat is designed for fan coil and chilled beam

applications alongside proportional valves and actuator systems

where a 0-10v proportional control output is required.

The thermostat also has a single speed fan output.

The operational mode of the fan (auto or continuous) is selected

at time of installation via DIL switches accessible on the rear of

the unit.

When the unit is in standby the fans are switched o.

Connection Diagram

Fan 1

COM

0V/

return

1 Speed

Fan

Electronics

Common In

Heating

24 Vac

Cool Heat

Cooling

0-10V outputs

0V 24V

Installation Instructions

Commissioning

Prior to re-tting the thermostat to the wallplate, the DIL switches

on the rear of the unit must be set to the desired setting.

Installation Instructions

Fan Con Fan Auto

Sw On

MOT WAX

DIL Switch options, shown in factory set position.

DIL Switch Descriptions

Switch 1: Fan Con - Fan will run whenever thermostat is in

heating or cooling mode.

Fan Auto - Fan will run whenever temperature is

0.2°C or more above/below (depending on heat/cool

mode) setpoint. When temperature reaches setpoint,

the fan will switch o.

Switch 2: MOT - Motorised valve actuator selection.

WAX - Wax valve actuator selection.

Mounting thermostat to the wallplate

To mount the thermostat to the wallplate, align the tabs on

the top of the thermostat with the apertures in the wallplate

and hinge the thermostat down, pressing rmly to engage

the securing clip in the wallplate.

Locking & limiting

To lock or limit the setting range turn the setting dial to 3 and

remove knob.

 Position the locking springs on the rear of the dial to the

desired position and re-mount the knob ensuring that

number 3 on the dial aligns with the reference mark on the

case.

Installation Instructions

User Instructions

GB User Instructions

Setting the temperature

Turn the setting dial to the required temperature.

Frost Protection

To activate frost protection, turn the dial below 10°C. Frost

protection becomes active at 8°C. If the temperature in the room

drops below 8°C then the output will activate.

When frost protection is activated the right LED will turn orange.

Standby Mode

In cooling mode, the standard frost protection is not available;

instead there is standby mode. When the dial is turned past 10°C

the unit enters standby mode and cooling will be inactive until the

dial is turned up past 10°C.

User Instructions

Heat Mode

Standby Mode

Cool Mode

LED lit green when

thermostat is powered

and fan is in continuous

mode

LED lit orange when fan

is running in auto mode

LED o when setpoint reached

LED red when heating

LED green when cooling

LED orange when frost

protection activated

Temperature setting dial

Frost protection mode

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Danfoss Thermostat

Danfoss

Danfoss TP5001RF Manuel utilisateur

Danfoss

Danfoss 140F1143 Manuel utilisateur

Danfoss

Danfoss TPOne-M Manuel utilisateur

Danfoss

Danfoss RAVV-RAV8 Manuel utilisateur

Danfoss

Danfoss ORT-01 Manuel utilisateur

Danfoss

Danfoss RET2001RF Manuel utilisateur

Danfoss

Danfoss C37 Manuel utilisateur

Danfoss

Danfoss RET2000 B Manuel utilisateur

Danfoss

Danfoss TP9 Manuel utilisateur

Danfoss

Danfoss KPU 61 Manuel utilisateur

Danfoss

Danfoss BasicPlus2 Manuel utilisateur

Danfoss

Danfoss TPONE-RF Manuel utilisateur

Danfoss

Danfoss REP24 Manuel utilisateur

Danfoss

Danfoss TP75-RF Manuel utilisateur

Danfoss

Danfoss ECL Comfort 310 Manuel utilisateur

Danfoss

Danfoss ECL Comfort 210 Manuel utilisateur

Danfoss

Danfoss HP75-1 Manuel utilisateur

Danfoss

Danfoss KPU 19 Manuel utilisateur

Danfoss

Danfoss TP7001 series Manuel utilisateur

Danfoss

Danfoss RET2000 B Manuel utilisateur

Danfoss

Danfoss TP7001 series Manuel utilisateur

Danfoss

Danfoss RET B + RF Mode d'emploi

Danfoss

Danfoss RET B Mode d'emploi

Danfoss

Danfoss RET2000 M Manuel utilisateur

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Honeywell

Honeywell CM721 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

Honeywell

Honeywell RLV4305 Manuel utilisateur

Honeywell

Honeywell Prestige 2.0 THX9421 Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur