Danfoss living connect Manuel utilisateur
Application
This documents provides information about the
Z-Wave commands supported by living connect®
and guidelines on the implementation of Z-Wave
controllers as well as general description of the
living connect® and how to mount it on a radiator.
living connect®is a electronic radiator thermostat.
It can be controlled by either a Danfoss LinkTM CC
(Central Controller) or a Z-Wave certified control-
ler.
(For control by Danfos LinkTM CC see separate da-
ta sheet)
living connect® uses Z-Wave wireless communica-
tion technology, is easy to install and is supplied
with adapters for all thermostatic valves manu-
factured by Danfoss and most other radiator
valve manufacturers.
living connect® is battery powered, compact and
very easy to operate with only three buttons on
the front.
The temperature can be changed at any time us-
ing the buttons on living connect®. The change is
transmitted directly to the controller, which can
synchronize the other electronic radiator thermo-
stats in the same room. living connect® features
an open-window function, which closes the valve
if the temperature in the room is falling dramati-
cally. Main features in a system with the control-
ler:
▪Energy saving
▪Easy to install
▪Easy to operate - only three buttons
▪Provides high comfort
▪Open window function
▪Valve exercise function
▪PID control
▪Weekly programs with variable set points for
each day
▪Battery lifetime 2 years, if properly suppor-
ted by the Z-Wave controller
▪Child lock
▪Frost protection
▪Backlit display
System example
Data Sheet
living connect®, Z-Wave Certified Electronic Ra-
diator Thermostat
Danfoss Heating Solutions VDHMB202 © Danfoss 09/2011 1
Code numbers Code no. Adapter (included) Language instructions
014G0001 Danfoss RA UK/DE/DK/NL
FR/PL/SE/FI
014G0002 Danfoss RA and M30 x 1.5 (K) UK/DE/DK/NL
FR/PL/SE/FI
Accessories Type Code no.
RAV & RAVL adaptor 014G0250
RA adaptor 014G0251
M30 x 1.5 (K) adaptor 014G0252
RTD adaptor 014G0253
Specification Control system/input Standard Z-Wave control units
Transmission frequency Wireless Z-Wave/868.42 MHz
Transmission range Up to 30 meters
Synchronizing Configurable (5 min. recommended)
Screen/display Grey digital with backlit
Actuator type Electromechanical
Software classification A
Control PID
Power supply 2x1.5V AA alkaline, class III (SELV)
Battery life 2 years
Low battery signal Battery icon and alarm bell will flash in display. If the battery
level is critical, the whole display will flash.
Ambient temperature 0 to 40⁰C
Transportation temperature range -20 to 65⁰C
Temperature setting range 4 to 28⁰C
Recommended use Residential
Open-window function Yes
Size RA: L: 91 mm Ø:51 mm/K: L78 mm Ø: 51 mm
Noise level < 30 dBA
Weight incl. battery 177 g
Safety classification Type 1
Mechanical strength 70 N (max. force from valve)
Maximum water temperature 90°C
Movement type Linear
Spindle movement 2-3 mm on valve
Maximum extension 4.5 mm
Temperature sampling Measures temperature every minute
Speed of adjustment 1 mm/s
Power consumption 3 mW in standby, 1.2 W when active
Ball pressure test 75°C
IP class* 20
* This thermostat should not be used in hazardous installations or in places where it will be exposed
to water.
Data Sheet living connect®, Z-Wave Certified Electronic Radiator Thermostat
2 VDHMB202 © Danfoss 09/2011 Danfoss Heating Solutions
Marking
Installation living connect® is supplied with adapters for
Danfoss RA valves and valves with M30X1.5
(K) connections (code no. 014G0002), two al-
kaline AA batteries and a 2 mm Allen key.
Inserting the batteries
Remove the battery cover and insert the two
batteries. Ensure that the batteries are cor-
rectly inserted. A capital "M" must flash on the
display before installation.
RA K
▪Start by mounting the adapter.
▪Tighten the RA adapter using the Allen
key. Tighten the K adapter by hand (max.
5 Nm).
▪Screw the thermostat onto the adapter
and hand-tighten (max. 5 Nm).
2 mm Allen key
▪Press and hold for approx. 3 seconds
to fix the thermostat.
Data Sheet living connect®, Z-Wave Certified Electronic Radiator Thermostat
Danfoss Heating Solutions VDHMB202 © Danfoss 09/2011 3
Connecting living connect®
to a Z-Wave controller
In Z-Wave connecting a device is called “Inclusion” or “Learn mode”.
To connect living connect® to a Z-Wave controller then:
▪Ensure living connect® is factory reset as explained in the user manual.
▪Activate "Inclusion" on the Z-Wave controller.
▪Quickly press and release the select button on living connect®.
▪Observe both controller and living connect® for status of the process.
Technical requirements:
▪After a succesful "Inclusion" the controller must send a WAKE_UP_INTERVAL_SET command to
living connect® in order to specify where and when living connect® should communicate wire-
lessly.
▪After sending the WAKE_UP_INTERVAL_SET command, the controller must assign return routes,
so living connect® can reach its destination i.e. the nodeID set in the WAKE_UP_INTERVAL_SET
command.
▪living connect® will not commence its periodic communications if it is in "Installation mode". "In-
stallation mode" is for physical installation and should not be confused with "Inclusion". Please
consult the user manual of living connect® for instructions on how to leave "Installation mode".
▪A Z-Wave controller will have access to all living connect® features, which are exposed using
standard Z-Wave command classes.
See other section of this document for more information.
Disconnecting living con-
nect® from a Z-Wave con-
troller
In Z-Wave disconnecting a device is called “Exclusion”.
To disconnect living connect® from a Z-Wave controller then:
▪Activate "Exclusion" on the Z-Wave controller.
▪Quickly press and release the select button on living connect®.
▪Observe both controller and living connect® for status of the process.
Activate special awake
mode on living connect®
living connect® will turn on radio communication for short periods of time at specific intervals in or-
der to communicate with its controller, unless such a controller has yet to be configured. When radio
communication is not needed by living connect® it will turn the radio off to conserve battery life.
If a user needs to configure a controller for living connect® or send more information to living con-
nect® then the user can activate a special 5 seconds awake mode by pressing the select button on
living connect®.
Data Sheet living connect®, Z-Wave Certified Electronic Radiator Thermostat
4 VDHMB202 © Danfoss 09/2011 Danfoss Heating Solutions
Important ▪The nodeID set in the WAKE_UP_INTERVAL_SET command must be for a permanently listening
device which reponds to the commands sent from living connect®. This means PC's with USB
sticks will only work if the PC is never turned off. If the controller is turned off for extended peri-
odes, living connect® will use the batteries too fast.
▪To preserve battery - Wake_Up_intervals should not be set to less than 5 min. Increasing the
time between intervals will increase battery life but can reduce user satisfaction due to long re-
action times.
▪Although living connect® supports single commands, multi commands must always be used to
ensure two years battery lifetime.
▪If multiple thermostats are installed in the same room it is important that the controller ensures
that they all have the same schedule and the same setpoint.
▪In order to ensure proper routing with battery operated devices, the controller must support
SUC.
living connect® and Z-
Wave repeaters
living connect® may benefit if more mains powered Z-Wave devices are added to a Z-Wave network.
Mains powered Z-Wave devices improve the reliability of a Z-Wave network as they can act as re-
peaters and thus provide alternate routes for communication.
Implemented Z-Wave de-
vice classes
Z-Wave Device Classes Device Class Implemented
Generic Device GENERIC_TYPE_THERMOSTAT
Specific Device SPECIFIC_TYPE_SETPOINT_THERMOSTAT
Supported and controlled
Z-Wave command classes
Z-Wave Command Classes Supported Description
COMMAND_CLASS_BATTERY Get current battery status of living connect®.
COMMAND_CLASS_CLIMATE_CONTROL_SCHEDULE Control a temperature offset to the ther-
mostat setpoint of living connect®. The tem-
perature offset is defined by schedules and
schedule overrides.
COMMAND_CLASS_CLOCK Set or get the current living connect® clock.
COMMAND_CLASS_MANUFACTURER_PROPRIETARY Special command used for communication
with a Danfoss Link system.
COMMAND_CLASS_MANUFACTURER_SPECIFIC Get manufacturer ID of system.
COMMAND_CLASS_MULTI_CMD A special Z-Wave command used by living
connect® to encapsulate multiple com-
mands in one command and thereby con-
serve battery life.
COMMAND_CLASS_PROTECTION Set or get living connect® local protection
mode.Possible local protection values are:
0 = no protection
2 = fully locked (tamperproof)
COMMAND_CLASS_THERMOSTAT_SETPOINT Set or get current thermostat setpoint of
living connect®.Heating setpoint is the only
supported setpoint type.
COMMAND_CLASS_VERSION Get version of product and command
classes.
COMMAND_CLASS_WAKE_UP A special Z-Wave command used by living
connect® to synchronize communication
with its controller.
Data Sheet living connect®, Z-Wave Certified Electronic Radiator Thermostat
Danfoss Heating Solutions VDHMB202 © Danfoss 09/2011 5
Data Sheet living connect®, Z-Wave Certified Electronic Radiator Thermostat
6 VDHMB202 © Danfoss 09/2011 Danfoss Heating Solutions
Data Sheet living connect®, Z-Wave Certified Electronic Radiator Thermostat
Danfoss Heating Solutions VDHMB202 © Danfoss 09/2011 7
Data Sheet living connect®, Z-Wave Certified Electronic Radiator Thermostat
Danfoss A/S
Heating Solutions
Haarupvaenget 11
8600 Silkeborg
Denmark
Phone:+45 7488 8000
Fax: +45 7488 8100
Email: [email protected]
www.heating.danfoss.com
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products
already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective
companies. Danfoss Heating Solutions and the Danfoss Heating Solutions logotype are trademarks of Danfoss A/S. All rights reserved.
8 VDHMB202 © Danfoss 09/2011 Danfoss Heating Solutions
Autres manuels pour living connect
5
Table des matières
Autres manuels Danfoss Thermostat
Danfoss
Danfoss RET B + RF Mode d'emploi
Danfoss
Danfoss TP4 Instructions de montage
Danfoss
Danfoss ECtemp Next Plus Manuel utilisateur
Danfoss
Danfoss GreenCon RC-T2 Manuel utilisateur
Danfoss
Danfoss TP9 Manuel utilisateur
Danfoss
Danfoss KP Series Manuel utilisateur
Danfoss
Danfoss DEVIreg 233 Manuel utilisateur
Danfoss
Danfoss DEVIreg 330 Manuel utilisateur
Danfoss
Danfoss TP5001 series Manuel utilisateur
Danfoss
Danfoss TP5000 RF Si Mode d’emploi
Danfoss
Danfoss TP5001 series Manuel utilisateur
Danfoss
Danfoss RET M Mode d'emploi
Danfoss
Danfoss TP5001 series Instructions d'utilisation
Danfoss
Danfoss TP6000M Manuel utilisateur
Danfoss
Danfoss FH-WS Manuel utilisateur
Danfoss
Danfoss RET2000B-RF Manuel utilisateur
Danfoss
Danfoss DEVIreg 316 Manuel utilisateur
Danfoss
Danfoss GreenCon RC-C2 Manuel utilisateur
Danfoss
Danfoss REP24 Manuel utilisateur
Danfoss
Danfoss DEVI DEVIreg 330 Manuel utilisateur
Manuels Thermostat populaires d'autres marques
EWELLY
EWELLY EW-181 Manuel utilisateur
Prolon
Prolon T1100 Instructions d'installation
Computherm
Computherm Q20 Manuel utilisateur
Heatmiser
Heatmiser neoStat Manuel utilisateur
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur
