D-Link DXS-3600-16S Manuel utilisateur
Quick Installation Guide
Краткое руководство по установке
3 Fan, AC Power Supply, 1 Expansion Slot, 8-Port 10GBase-X SFP+,
3 Management Stacked Switch /
Управляемый стекируемый коммутатор 3 уровня с 8 портами
10GBase-X SFP+, 1 слотом расширения, источником питания AC и
3 вентиляторами
DX -3600-16
Introduction
This Quick Installation Guide gives instructions for setting up the D- ink DXS-3600-16S switch. The model
you have purchased may appear slightly different from those shown in the illustrations. For more detailed
information about the device, its components, making network connections and technical specifications,
please refer to the User Manual.
Package Contents
• DXS-3600-16S Switch
• Power Cord
• AC power supply module
• 3 Fan modules
• DB-9 to RJ-45 console cable
• 4 Rubber Feet
• 2 Mounting Brackets
• Mounting kit
• Quick Installation Guide
• Warranty Certificate
• CD ROM
If any of the above items are damaged or missing, please contact your local reseller for replacement.
2
Hardware Overview
Front Panel
Port Description
SD Card Slot This port can be used to insert an external SD memory card. The maximum
capacity SD card that can be inserted into this port is 32 Gb.
Management port (MGMT) This is a 10/100/1000 Mbps Out-Of-Band management port that can be used to
configure this switch without being connected to the network.
Console Port This port is an RJ-45 connection port that can be used to connect to the Command
ine Interface (C I) of this switch for configuration, management and monitoring.
This port uses a special console cable (included with the packing) with a DB-9
interface to connect the Switch to a PC’s COM port.
Ports 1-8 This switch is equipped with SFP/SFP+ ports. These ports can operate at 10 Gbps
speeds and support a vast collection of SFP, WDM SFP, SFP+, WDM SFP+ and
QSFP+ transceivers.
Expansion Module Slot This slot can be equipped with several kinds of additional modules. These modules
are not included and should be bought separately:
• DXS-3600-EM-4XT (Four 10GBase-T Copper ports).
• DXS-3600-EM-8T (Eight 1000Base-T Copper ports).
• DXS-3600-EM-4QXS (Four 40Gbps QSFP+ transceiver slots).
• DXS-3600-EM-8XS (Eight 10Gbps SFP+ transceiver slots).
3
LED Indicators
LED Indicative Colour tatus Description
Power 1,
Power 2
Green /
Amber
Solid Green Power on.
Solid Amber Power supply fails.
ight off Power off.
Management
(MGMT)
Green Solid Green A link to the management port was successfully established.
Blinking Green Activity on this port is taking place.
ight off There is no link present or when this interface was shutdown from within
the switch’s configuration.
Console Green Blinking Green During the Power-On Self Test (POST).
Solid Green A user is logged in through the console port.
ight off After the POST finished successfully and no user is connected to the
console port.
Fan1, Fan2,
Fan3
Green /
Amber
Solid Green When the fan is operating normally.
Solid Amber When the switch is booting up or when a diagnostics test is taking place.
Blinking Amber When a fan fails.
ight off When the fan is not receiving power.
SD Green / Red Solid Green If a Secure Digital (SD) card is plugged in.
Blinking Green The Switch is reading or writing data to and from the SD card.
ight off No SD card is plugged into the SD port.
Solid Red An SD card failure has been detected.
ink/Act Green /
Amber
Solid Green There is a secure connection to a 10 Gbps Ethernet device at any of the
ports.
Blinking Green A 10 Gbps port is active.
Solid Amber There is a secure Ethernet connection to a 1 Gbps Ethernet device at
any of the ports.
Blinking Amber A 1 Gbps port is active.
ight off There is no link or activity.
4
Rear Panel
Component Description
Power Supply Module Slots These slots can be equipped with two kinds of additional modules. Only one power
supply module is included. Any additional modules should be bought separately.
• DXS-PWR300AC (300W AC power supply tray with front-to-back airflow).
• DXS-PWR300DC (300W DC power supply tray with front-to-back airflow).
Fan Module Slots • DXS-3600-FAN-FB (normal fan tray with front-to-back airflow).
Installation
Desktop or helf Installation
When installing the switch on a desktop or shelf, the rubber feet included with the device must be attached
on the bottom at each corner of the device’s base. Allow enough ventilation space between the device and
the objects around it.
Rack Installation
The switch can be mounted in a standard 19-inch rack using the provided mounting brackets.
5
How to install the mounting brackets onto the switch (figure above) and onto the rack (figure below):
1. Fasten the mounting brackets A and B to the sides of the switch using the screws provided, as seen in the
figure above.
2. Fasten the mounting bracket C in the appropriate open space in the rack using the screws provided, as
seen in the figure below.
3. Simply slide the switch (fastened bracket B into fastened bracket C) into the rack.
4. astly, fasten mounting bracket A to the rack using the screws provided.
Make sure that there is adequate space around the Switch to allow for proper air flow, ventilation, and
cooling.
Installing Transceivers into the Transceiver Ports
The Switch is equipped with Small Form-factor Pluggable plus (SFP+) ports, which supply connecting SFP,
WDM SFP, SFP+, WDM SFP+ and QSFP+ transceivers.
6
Connecting to Power
Installing an AC Power Module
Connect the one end of the AC power cord supplied to the AC power connector and the other end into a
properly grounded electrical outlet. The switch will automatically adjust the AC power setting to adapt to any
voltage supply in the range from 100~240VAC at 50~60Hz.
In addition, an optional second AC power supply module can be plugged into the second power supply
module slot. When the primary AC power connection fails, the secondary AC power connection will take over
all the power immediately and automatically. The AC power supply modules are hot-swappable, meaning,
that they can be inserted and removed while the switch is powered on.
Install an AC Power Supply Module as shown on the picture below.
Installing a DC Power Module
This switch supports a unique dual power input feature. The DC power module will be activated if the AC
power module turns off.
1. Install a DC Power Supply Module. Use the grounding screw on the DC Power Module and a minimum of
18 AWG stranded copper wire to ground the switch.
2. Connect the one end of the DC power cord supplied to a DC power module, that will be activated when
the AC power is not working, and to a power source (-48VDC/5.2A). Please make sure that connection
polarity (positive and negative) is correct.
7
The DC power and AC power of the device will back up each other immediately when one of the power
sources fails. If both power sources fail, unplug the switch. When the power source has been restored, plug
the switch’s power back in.
NOTE: the Power Modules all support a specific airflow direction. This air-flow direction must be the same as
the Fan Module installed. By default the airflow direction of the Power Module and Fan Module installed is
front-to-back.
Installing Fan Modules into the Fan Module Ports
ocated on the rear panel of this switch there are three fan module ports.
The user can easily remove and insert fan modules into these ports.
witch Connections
witch to End Node
End node is a generic name for edge networking devices that will be connected to this switch. Typical
examples of end nodes are Personal Computers (PCs), Notebooks, Access Points, Print Servers, VoIP
Phones and more. Each end node will be outfitted with a 10/100/1000 Mbps, RJ-45, networking port.
Normally end nodes will connect to this switch by using a standard twisted-pair, UTP/STP, network cable.
After a successful connection, the corresponding ink/Act light will illuminate and blink to indicate that packet
activity is taking place on that port.The diagram below displays a typical end node connected to the Switch.
8
witch to another witch
Another popular configuration is to connect this switch to another switch. This network typography is
considered when one Switch does not have enough ports to cater for all the end nodes in the network. There
is a great deal of flexibility in the type of cabling that can be used to interlink switches.
Two or more switches can also be interlinked using fiber-optic cables or direct-attached cables via the
switch’s SFP and SFP+ ports. astly two or more switches can also be interlinked using QSFP+ interfaces
supported by the DXS-3600-EM-4QXS optional modules.
witch tacking
The DXS-3600-16S supports stacking 4 switches together while being managed by one IP address through
Telnet, the Web User Interface, the RJ-45 console port or through SNMP. This cost effective switch provides
an affordable solution for administrators to upgrade their networks using the DXS-3600-EM-4QXS module to
scale and stack the switches.
• Duplex Chain – The Duplex Chain topology stacks switches together in a chain-link format. Each switch in
a chain is connected to the upper and the lower units, while the upper and the lower switches are not
connected. If there is a break in the chain, then data transfer will obviously be affected.
• Duplex Ring – The Duplex Ring stacks switches in a ring or circle format. Each switch in a chain is
connected to the upper and the lower units, the upper and the lower switches are also connected. This
topology is very resilient due to the fact that if there is a break in the ring, data can still be transferred through
the stacking cables between switches in the stack.
The DXS-3600-EM-4QXS module uses the last two QSFP+ ports to make the following stacking topologies.
The figure below illustrates how switches can be stacked in a Duplex Chain formation using the
DXS-3600-EM-4QXS module.
9
The figure below illustrates how switches can be stacked in a Duplex Ring formation using the
DXS-3600-EM-4QXS module.
witch to a erver
When configuring a network, users will most likely have to add a server or two to this switch. Generally, any
port on this switch can be used to connect to a server.
10
Autres manuels pour DXS-3600-16S
1
Table des matières
Langues :
Autres manuels D-Link Changer
D-Link
D-Link DGS-1005D/B Manuel utilisateur
D-Link
D-Link DUB-H7 - Hub - USB Manuel utilisateur
D-Link
D-Link DXS-3610 Series Manuel
D-Link
D-Link DUB-2340 Manuel utilisateur
D-Link
D-Link xStack DGS-3420 Series Manuel utilisateur
D-Link
D-Link DKVM-2K Manuel utilisateur
D-Link
D-Link DGS-3630 SERIES Manuel utilisateur
D-Link
D-Link DGS-6600-48T Mode d’emploi
D-Link
D-Link xStack DGS-3400 Series Manuel utilisateur
D-Link
D-Link DES-1008E Manuel utilisateur
D-Link
D-Link DKVM-4U Manuel utilisateur
D-Link
D-Link DES-7210-BASE Manuel utilisateur
D-Link
D-Link DFE-916x Manuel utilisateur
D-Link
D-Link DES-3350SR Manuel utilisateur
D-Link
D-Link DIS-F200G Series Manuel utilisateur
D-Link
D-Link GO-SW-24GE Manuel utilisateur
D-Link
D-Link DAS-3636 Manuel utilisateur
D-Link
D-Link DES-1024A Manuel utilisateur
D-Link
D-Link DES-1024D Manuel utilisateur
D-Link
D-Link DES-1005P Manuel utilisateur
Manuels Changer populaires d'autres marques
Ruijie
Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation
Altinex
Altinex DA1914SX Manuel utilisateur
MiLAN
MiLAN MIL-SM2401M Manuel utilisateur
RJM
RJM MASTERMIND PBC/6X Manuel utilisateur
Atlas
Atlas MMK-KVM8 Manuel utilisateur
Cabletron Systems
Cabletron Systems GIGAswitch GSR-16 Manuel utilisateur