D-Link DAS-3636 Manuel utilisateur

CLI Reference Manual

Product Model: DAS-3636

VDSL2 Switch

Release .00

____________________________________________________________________________

Information in this document is subject to change without notice.

Re roduction in any manner whatsoever without the written ermission of D-Link Cor oration is strictly forbidden.

Trademarks used in this text: D-Link and the D-LINK logo are trademarks of D-Link Cor oration; Microsoft and Windows are

registered trademarks of Microsoft Cor oration.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or

their roducts. D-Link Cor oration disclaims any ro rietary interest in trademarks and trade names other than its own.

July 2009 P/N 651370012005G

Table of Contents

INTRODUCTION............................................................................................................................1

USING THE CONSOLE CLI..........................................................................................................3

COMMAND SYNTAX.....................................................................................................................6

BASIC SWITCH COMMANDS ......................................................................................................8

MODIFY BANNER AND PROMPT COMMANDS.......................................................................28

SWITCH UTILITY COMMANDS..................................................................................................32

BASIC IP COMMANDS...............................................................................................................44

ROUTING TABLE COMMANDS.................................................................................................48

IPV6 NEIGHBOR DISCOVERY COMMANDS............................................................................5

LIMITED IP MULTICAST ADDRESS..........................................................................................54

SWITCH PORT COMMANDS......................................................................................................61

ARP COMMANDS........................................................................................................................66

DHCP RELAY..............................................................................................................................78

EXTERNAL ALARM COMMANDS.............................................................................................84

NETWORK MANAGEMENT (SNMP) COMMANDS...................................................................86

TIME AND SNTP COMMANDS.................................................................................................12

VLAN COMMANDS...................................................................................................................125

Q-IN-Q COMMANDS.................................................................................................................15

LINK AGGREGATION COMMANDS........................................................................................155

IGMP SNOOPING COMMANDS...............................................................................................16

IGMP MULTICAST VLAN COMMANDS...................................................................................175

MLD MULTICAST VLAN COMMANDS....................................................................................183

MLD SNOOPING COMMAND LIST..........................................................................................191

PORT MIRRORING COMMANDS.............................................................................................2 4

LOOP-BACK DETECTION COMMANDS.................................................................................2 7

MULTIPLE SPANNING TREE PROTOCOL (MSTP) COMMANDS.........................................211

FORWARDING DATABASE COMMANDS...............................................................................247

CONNECTIVITY FAULT MANAGEMENT COMMANDS..........................................................254

VLAN COUNTER COMMANDS................................................................................................273

QOS COMMANDS.....................................................................................................................276

TRAFFIC CONTROL COMMANDS...........................................................................................286

SAFEGUARD ENGINE COMMANDS.......................................................................................29

PORT SECURITY COMMANDS................................................................................................293

SSL COMMANDS......................................................................................................................297

SSH COMMANDS......................................................................................................................3 3

ACCESS AUTHENTICATION CONTROL COMMANDS..........................................................327

FILTER COMMANDS (DHCP SERVER/NETBIOS)..................................................................392

ACCESS CONTROL LIST (ACL) COMMANDS.......................................................................396

VDSL COMMANDS ..................................................................................................................41

NETWORK MONITORING COMMANDS..................................................................................44

PASSWORD RECOVERY COMMAND LIST............................................................................466

COMMAND HISTORY LIST.......................................................................................................47

PASSWORD RECOVERY PROCEDURE.................................................................................474

DAS-3600 Series Ethernet over VDSL Switch CLI Reference Manual

INTRODUCTION

The VDSL Switch can be managed through the VDSL Switch’s serial ort, Telnet, or the Web-based management agent. The

Command Line Interface (CLI) can be used to configure and manage the VDSL Switch via the serial ort or Telnet interfaces.

This manual rovides a reference for all of the commands contained in the CLI. Configuration and management of the VDSL

Switch via the Web-based management agent is discussed in the User Manual.

This manual rovides a reference for all of the commands contained in the CLI for the DAS-3626. Exam les resent in this

manual may refer to either member of this series and may show different ort counts, but are universal to this series of switches,

unless otherwise stated. Configuration and management of the VDSL Switch via the Web-based management agent is discussed in

the User Guide.

NOTE: For the remainder of this manual, the DAS-3626 switches will be referred to as simply

the Switch or the DAS-3600 Series.

Accessing the Switch via the Serial Port

The Switch’s serial ort’s default settings are as follows:

•115200 baud

•no parity

•8 data bits

•1 stop bit

A com uter running a terminal emulation rogram ca able of emulating a VT-100 terminal and a serial ort configured as above

is then connected to the Switch’s serial ort via an RS-232 DB-9 cable.

With the serial ort ro erly connected to a management com uter, the following screen should be visible. If this screen does not

a ear, try ressing Ctrl+r to refresh the console screen.

DAS-3626 VDSL2 Switch

Command Line Interface

Firmware: Build 1 00 B042

UserName:

Figure 1-1. Initial CLI screen

There is no initial username or assword. Just ress the Enter key twice to dis lay the CLI in ut cursor − DAS-3626:admin#.

This is the command line where all commands are in ut.

DAS-3600 Series Ethernet over VDSL Switch CLI Reference Manual

Setting the Switch’s IP Address

Each Switch must be assigned its own IP Address, which is used for communication with an SNMP network manager or other

TCP/IP a lication (for exam le BOOTP, TFTP). The Switch’s default IP address is 10.90.90.90. Users can change the default

Switch IP address to meet the s ecification of your networking address scheme.

The Switch is also assigned a unique MAC address by the factory. This MAC address cannot be changed, and can be found on the

initial boot console screen – shown below.

boot Procedure V1 03 B016

-------------------------------------------------------------------------------

Power On Self Test 100%

MAC Address : 00-26-54-60-54-60

H/W Version :

Please Wait, Loading V1 02 B018 Runtime Image [1] 100%

R2R3R4R5R6

BME 1:POST: Success

BME 2:POST: Success

BME 3:POST: Success

BME 1:Download: Downloaded successfully

BME 2:Download: Downloaded successfully

BME 3:Download: Downloaded successfully

VDSL driver version 5 3 0 13IK005010

UART init 100 %

Figure 1-2. Boot screen

The Switch’s MAC address can also be found in the Web management rogram on the Switch Information (Basic Settings)

window on the Configuration menu.

The IP address for the Switch must be set before it can be managed with the Web-based manager. The Switch IP address can be

automatically set using BOOTP or DHCP rotocols, in which case the actual address assigned to the Switch must be known.

The IP address may be set using the Command Line Interface (CLI) over the console serial ort as follows:

1. Starting at the command line rom t, enter the commands confi ipif System ipaddress

xxx.xxx.xxx.xxx/yyy.yyy.yyy.yyy. Where the x’s re resent the IP address to be assigned to the IP interface named

System and the y’s re resent the corres onding subnet mask.

2. Alternatively, users can enter confi ipif System ipaddress xxx.xxx.xxx.xxx/z. Where the x’s re resent the IP address to

be assigned to the IP interface named System and the z re resents the corres onding number of subnets in CIDR

notation.

The IP interface named System on the Switch can be assigned an IP address and subnet mask which can then be used to connect a

management station to the Switch’s Telnet or Web-based management agent.

DAS-3626:admin#config ipif System ipaddress 10 24 73 21/8

Command: config ipif System ipaddress 10 24 73 21/8

Success

DAS-3626:admin#

Figure 1-3. Assigning an IP Address screen

In the above exam le, the Switch was assigned an IP address of 10.24.73.21 with a subnet mask of 255.0.0.0. The system message

Success indicates that the command was executed successfully. The Switch can now be configured and managed via Telnet,

SNMP MIB browser and the CLI or via the Web-based management agent using the above IP address to connect to the Switch.

DAS-3600 Series Ethernet over VDSL Switch CLI Reference Manual

USING THE CONSOLE CLI

The DAS-3600 Series su orts a console management interface that allows the user to connect to the Switch’s management agent

via a serial ort and a terminal or a com uter running a terminal emulation rogram. The console can also be used over the

network using the TCP/IP Telnet rotocol. The console rogram can be used to configure the Switch to use an SNMP-based

network management software over the network.

This cha ter describes how to use the console interface to access the Switch, change its settings, and monitor its o eration.

Note: Switch confi uration settin s are saved to non-volatile RAM usin the save command. The

current confi uration will then be retained in the Switch’s NV-RAM, and reloaded when the Switch is

rebooted. If the Switch is rebooted without usin the save command, the last confi uration saved to NV-

RAM will be loaded.

Connecting to the Switch

The console interface is used by connecting the Switch to a VT100-com atible terminal or a com uter running an ordinary

terminal emulator rogram (e.g., the HyperTerminal rogram included with the Windows o erating system) using an RS-232C

serial cable. Your terminal arameters will need to be set to:

•VT-100 compatible

•115200 baud

•8 data bits

•No parity

•One stop bit

•No flow control

Users can also access the same functions over a Telnet interface. Once users have set an IP address for your Switch, users can use

a Telnet rogram (in VT-100 com atible terminal mode) to access and control the Switch. All of the screens are identical, whether

accessed from the console ort or from a Telnet interface.

After the Switch reboots and users have logged in, the console looks like this:

DAS-3626 VDSL2 Switch

Command Line Interface

Firmware: Build 1 02-B018

UserName:

Figure 2-1. Initial Console screen after logging in

Commands are entered at the command rom t, DAS-3626:admin#.

There are a number of hel ful features included in the CLI. Entering the ? command will dis lay a list of all of the to -level

commands.

DAS-3600 Series Ethernet over VDSL Switch CLI Reference Manual

cable_diag ports

cfm linktrace

cfm loopback

clear

clear address_binding dhcp_snoop binding_entry ports

clear arptable

clear attack_log

clear cfm pkt_cnt

clear counters

clear ethernet_oam ports

clear fdb

clear historical_counters ports

clear igmp_snooping data_driven_group

clear igmp_snooping statistic counter

clear log

clear mac_based_access_control auth_mac

clear mld_snooping data_driven_group

clear mld_snooping statistic counter

clear port_security_entry

clear vlan_counter statistics

CTRL+C ESC q Quit SPACE n Next Page ENTER Next Entry a All

Figure 2-2. The ? Command

When users enter a command without its required arameters, the CLI will rom t users with a Next possible completions:

message.

DAS-3626:admin#config account

Command: config account

Next possible completions:

DAS-3626:admin#

Figure 2-3. Example Command Parameter Help

In this case, the command confi account was entered with the arameter <username>. The CLI will then rom t users to enter

the <username> with the message, Next possible completions:. Every command in the CLI has this feature, and com lex

commands have several layers of arameter rom ting.

In addition, after ty ing any given command lus one s ace, users can see all of the next ossible sub-commands, in sequential

order, by re eatedly ressing the Tab key.

To re-enter the revious command at the command rom t, ress the u arrow cursor key. The revious command will a ear at

the command rom t.

DAS-3626:admin#config account

Command: config account

Next possible completions:

DAS-3626:admin#config account

Command: config account

Next possible completions:

DAS-3626:admin#

Figure 2-4. Using the Up Arrow to Re-enter a Command

DAS-3600 Series Ethernet over VDSL Switch CLI Reference Manual

In the above exam le, the command confi account was entered without the required arameter <username>, the CLI returned

the Next possible completions: <username> rom t. The u arrow cursor control key was ressed to re-enter the revious

command (confi account) at the command rom t. Now the a ro riate username can be entered and the confi account

command re-executed.

All commands in the CLI function in this way. In addition, the syntax of the hel rom ts are the same as resented in this manual

− angle brackets < > indicate a numerical value or character string, braces { } indicate o tional arameters or a choice of

arameters, and brackets [ ] indicate required arameters.

If a command is entered that is unrecognized by the CLI, the to -level commands will be dis layed under the Available

commands: rom t.

DAS-3626:admin#the

Available commands:

? cfm

clear config create delete

disable download enable login

logout ping ping6 reboot

reconfig reset save show

upload

DAS-3626:admin#

Figure 2-5. The Next Available Commands Prompt

The to -level commands consist of commands such as show or confi . Most of these commands require one or more arameters

to narrow the to -level command. This is equivalent to show what? or confi what? Where the what? is the next arameter.

For exam le, if users enter the show command with no additional arameters, the CLI will then dis lay all of the ossible next

arameters.

DAS-3626:admin#show

Command: show

Next possible completions:

802 1p 802 1x access_profile account

accounting alarm arpentry asymmetric_vlan

attack_log authen authen_enable authen_login

authen_policy authentication authorization bandwidth_control

bpdu-filter cfm command_history config

current_config dhcp_relay dot1v_protocol_group

dscp_replace_priority error external_alarm

fdb filter firmware greeting_message

gvrp hardware igmp_snooping ipif

ipif_ipv6_link_local_auto iproute ipv6

jumbo_frame lacp_port limited_multicast_addr

link_aggregation log log_save_timing

log_support_module loopdetect lpr

mac_spoof_detect max_mcast_group mcast_filter_profile

mirror mld_snooping module_info multicast

multicast_fdb packet port port_security

port_vlan ports pvid qinq

radius ratelimit rmt router_ports

safeguard_engine scheduling scheduling_mechanism

serial_port session snmp sntp

ssh ssl stp switch

syslog system_severity system_usage_threshold

time time_range traffic

traffic_segmentation trusted_host utilization

vdsl vlan vlan_counter vlan_translation

vlan_translation_profile vlan_trunk

DAS-3626:admin#

Figure 2-6. Next possible completions: Show Command

In the above exam le, all of the ossible next arameters for the show command are dis layed. At the next command rom t, the

u arrow was used to re-enter the show command, followed by the account arameter. The CLI then dis lays the user accounts

configured on the Switch.

Table des matières

Autres manuels D-Link Changer

D-Link

D-Link DKVM-222 Manuel utilisateur

D-Link

D-Link DES-1016D - Switch Manuel utilisateur

D-Link

D-Link DES-3528 - xStack Switch - Stackable Manuel utilisateur

D-Link

D-Link DKVM-16 - KVM Switch Manuel utilisateur

D-Link

D-Link KVM-221 2 Manuel utilisateur

D-Link

D-Link DGS-1250-52XMP Manuel utilisateur

D-Link

D-Link D DGS-3048 DGS-3048 Manuel utilisateur

D-Link

D-Link DES-1008P Manuel utilisateur

D-Link

D-Link DES-3252P - Web Smart Switch Manuel utilisateur

D-Link

D-Link xStack DGS-3200-10 Manuel utilisateur

D-Link

D-Link DXS-3250E - xStack Switch Manuel utilisateur

D-Link

D-Link DWS-1008 Manuel utilisateur

D-Link

D-Link 809TC - Hub - EN Manuel utilisateur

D-Link

D-Link DXS-3227P - xStack Switch - Stackable Manuel utilisateur

D-Link

D-Link GO-SW-5E Manuel utilisateur

D-Link

D-Link DGS-1520-28MP Manuel utilisateur

D-Link

D-Link xStack DGS-3120 Series Manuel utilisateur

D-Link

D-Link DGS-1520-52 Manuel utilisateur

D-Link

D-Link DGS-1100-10MP Manuel utilisateur

D-Link

D-Link DES-3226 Mode d’emploi

D-Link

D-Link DGS-1016TL Manuel utilisateur

D-Link

D-Link DWS-3227P - xStack Switch - Stackable Manuel utilisateur

D-Link

D-Link DGS-3208F Manuel utilisateur

D-Link

D-Link RG-S8614 Manuel d'installation et d'exploitation

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Manuel utilisateur