D-Link DGS-1520-28MP Manuel utilisateur
D-Link
DGS-1520-28MP
20 10/100/1000Base-T PoE Ports + 4 100/1000/2.5GBase-T PoE Ports + 2 10GBase-T
Ports + 2 10GBase-X SFP+ Ports Sta kable Smart Managed Swit h
Управляемый L3 стекируемый коммутатор с 20 портами 10/100/1000Base-T,
4 портами 100/1000/2.5GBase-T, 2 портами 10GBase-T и 2 портами 10GBase-X
SFP+ (24 порта PoE 802.3af/at, PoE-бюджет 370 Вт; 740 Вт с DPS-700)
Quick Installation Guide
Краткое руководство по установке
Infor ation in this docu ent is subject to change without notice.
© 2021 D-Link Corporation. All rights reserved.
Pa kage Contents
Open the shipping carton of the switch and carefully unpack its contents. The model you
have purchased may appear slightly different from the one shown in the illustrations. The
carton should contain the following items:
One DGS-1 20-28MP switch
One AC power cord
One power cord retainer
One console cable (RJ-4 to RS-232)
One rack mounting kit (two brackets and screws)
Four rubber feet with adhesive backing
One Quick Installation Guide
Front Panel Des ription
The front panel of the switch contains the following items:
20 10/100/1000Base-T PoE ports
4 100/1000/2. GBase-T PoE ports
2 10GBase-T ports
2 10GBase-X SFP+ ports
RJ-4 console port
LEDs: Power, RPS, Console, Fan Error, Link/Activity/Speed Mode, PoE Mode, Link/
Activity/Speed (per port), PoE OK/PoE Fail (per PoE port), Stack ID
Mode, Reset/ZTP buttons
Figure 1 — DGS-1520-28MP front panel
Front Panel LEDs
The front panel of the switch contains the following LEDs: Power, RPS, Console, Fan
Error, Link/Activity/Speed Mode, PoE Mode, Link/Activity/Speed (per port), PoE OK/PoE
Fail (per PoE port), Stack ID.
Location LED Color Status Description
! "
!#
"$$$#
%&
'&
!(
%&'&!
"()$#
" (
)$#
( " (
)$#
%&'&!
"()$#
*+ ,- ./*+$)//
/
0 ./////
/ ./ / / )$!
//
./ / 1
./ $ /
2/$
,3&,33&,333.
!
%&
'&
!
' ,333 ()!
/$//!
+,333
()!/$//!
*
!
') ' ,3&,33 ()!
/$//!
+
,3&,33()!/$//!
4
*
!
,33&,333&
5.!
%&
'&
!
' 533 ()!
/$//!
+533
()!/$//!
*
!
') ',33&,333()!
/$//!
+
,33&,333()!/$//!
*
!
,3.! %&
'&
!
',3)!/$/
/!
+ ,3
)!/$//!
*
!
') ' ,333 ()!
/$//!
+,333
()!/$//!
*
!
,367
!
%&
'&
!
',3)!/$/
/!
+ ,3
)!/$//!
*
!
') ' ,333 ()!
/$//!
+,333
()!/$//!
*
!
! 8&
+ / )
$!!+/$//!
+/
9
') +/:)$;
!!+$+
!)$$/
+/
Rear Panel Des ription
The rear panel of the switch contains the following items:
AC power connector (100 to 240 VAC, 0 to 60 Hz)
Power cord retainer slot
SWITCH GND: grounding screw for attaching the terminal lug ring of the grounding
cable to the switch
Kensington-compatible security lock slot
Redundant Power Supply port
Figure 2 — DGS-1520-28MP rear panel
Side Panel Des ription
The left-hand panel of the switch has heat vents to dissipate heat. Do not block these
openings, and leave at least 1 cm of space at the rear and sides of the switch for proper
ventilation. Be reminded that without proper heat dissipation and air circulation, system
components might overheat, which could lead to system failure. Also the left- and right-
hand panels of the switch have four fans and rack-mounting screw holes.
Figure 3 — DGS-1520-28MP side panels
Swit h Installation
This section will discuss the hardware installation guidelines that the user must follow in
5
order to properly and safely install this switch into the appropriate environment.
Visually inspect the power cord and see that it is fully secured to both the power
connector, on the Switch, and the electrical outlet that supplies power.
Install the Switch in a fairly cool and dry place within the acceptable operating
temperature and humidity ranges.
Install the Switch in a site free from strong electromagnetic field generators such as
motors, vibration, dust, and direct exposure to sunlight.
Installing the Switch without a Rack
This section is used to guide the user through installing the switch in an area other than a
switch rack. Attach the included rubber feet to the bottom of the switch. Take note that
there should be marked blocks on the bottom of the switch to indicate where to attach the
rubber feet. These markings are usually found in each corner on the bottom of the device.
The rubber feet cushion the switch, protecting the casing from scratches and preventing it
from scratching other surfaces.
Figure 4 — Attaching rubber feet to the switch
Install the switch on a sturdy, level surface that can support the weight of the switch. Do
not place any heavy objects on the switch. Make sure that there is proper heat dissipation
from and adequate ventilation around the switch. Leave at least 10 cm of space at the
front, sides, and rear of the switch for ventilation.
Installing the Switch in a Standard 19'' Rack
This section is used to guide the user through installing the switch into a switch rack. The
switch can be mounted in a standard 19"(1U) rack using the provided mounting brackets.
Fasten the mounting brackets to the sides of the switch using the screws provided.
Figure 5 — Attaching rack- ount brackets to the switch
Fasten the mounting brackets in any available open space in the rack using the screws
<
provided.
Figure 6 — Installing the switch in a rack
Installing Trans eivers into the Trans eiver Ports
The switch is equipped with Small Form-factor Pluggable (SFP) and Enhanced Small
Form-factor Pluggable (SFP+) ports that can be used to connect various other networking
devices to this switch that do not support the standard RJ-4 wiring connection. These
ports are generally used to connect this switch to optical fiber connections and can be
used to connect devices to the switch over great distances. The maximum distance that
the RJ-4 wiring connection can reach is 100 meters. Fiber optic connections can span
several kilometers.
Figure 7 — Inserting transceivers into the transceiver ports
Conne ting AC Power to the Swit h
Plug one end of the AC power cord into the power socket of the switch and the other end
into the local power source outlet.
=
Power Failure (AC Power)
In the event of a power failure, just as a precaution, unplug the power cord from the switch.
After the power returns, plug the power cord back into the power socket of the switch.
Installing the AC Power Cord Retainer
To prevent accidental removal of the AC power cord, it is recommended to install the
power cord retainer together with the power cord. With the rough side facing down, insert
the tie wrap into the hole below the power socket.
Figure 8 — Insert tie wrap into the switch
Plug the AC power cord into the power socket of the switch.
Figure 9 — Connect the power cord to the switch
Slide the retainer through the tie wrap until the end of the cord.
-
Figure 10 — Slide the retainer through the tie wrap
Circle the tie of the retainer around the power cord and into the locker of the retainer.
Figure 11 — Circle around the power cord
Fasten the tie of the retainer until the power cord is secured.
Figure 12 — Secure the power cord
>
Installing the Redundant Power Supply (RPS)
The Redundant Power Supply (RPS) is designed to conform to the wattage requirements
of D-Link’s Ethernet and Gigabit switches. It is an external RPS unit enclosed in solid
metal case with sockets to connect AC or DC power sources on one end, and to connect
to a switch’s internal power supply on the other end. The RPS provides a low-cost, simple
solution to the problem of an inadvertent failure of the internal power supply of an Ethernet
switch, which can result in the shutdown of that switch, the devices attached to its ports, or
an entire network.
CAUTION: Do not connect the RPS to AC power before the DC power cable is
connected. This might damage the internal power supply.
CAUTION: Leave at least 1 cm (6 inches) of space at the rear of the switch when
an RPS is installed to prevent cable damage.
DPS-700 Redundant Power Supply
The DPS-700 is connected to the Master Switch using a 22-pin DC power cable. A
standard, three-pronged AC power cable connects the redundant power supply to the main
power source.
Figure 13 — Rear view of the DPS-700 connected to the swicth
CAUTION: Do not connect the DPS-700 to the switch by using the 14-pin DC power
cable. It may cause damage when using the wrong DC power cable. ONLY use the
22-pin DC power cable.
,3
Table des matières
Langues :
Autres manuels D-Link Changer
D-Link
D-Link DXS-3250 - xStack Switch - Stackable Manuel utilisateur
D-Link
D-Link DWS-1008 Mode d’emploi
D-Link
D-Link DXS-3227 - xStack Switch - Stackable Manuel utilisateur
D-Link
D-Link DGS-1008T Manuel utilisateur
D-Link
D-Link xStack DES-3200-28P Manuel utilisateur
D-Link
D-Link DGS-3630 SERIES Manuel utilisateur
D-Link
D-Link Web Smart Switch DGS-1210-16 Manuel utilisateur
D-Link
D-Link DGS-1005D - Switch Manuel utilisateur
D-Link
D-Link DCH-G601 Manuel utilisateur
D-Link
D-Link GO-SW-5E Manuel utilisateur
D-Link
D-Link DES-108 Manuel utilisateur
D-Link
D-Link DGS-3000 series Manuel utilisateur
D-Link
D-Link DGS-1005D - Switch Manuel utilisateur
D-Link
D-Link DGS-1008P Manuel utilisateur
D-Link
D-Link DAS-3626 Manuel utilisateur
D-Link
D-Link DES-3010FA Manuel utilisateur
D-Link
D-Link DGS-1008D - Switch Manuel utilisateur
D-Link
D-Link DGS-F1210 Series Manuel utilisateur
D-Link
D-Link DGS-1216T - Switch Manuel utilisateur
D-Link
D-Link xStack DGS-3612G series Manuel utilisateur
Manuels Changer populaires d'autres marques
Ruijie
Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation
Altinex
Altinex DA1914SX Manuel utilisateur
MiLAN
MiLAN MIL-SM2401M Manuel utilisateur
RJM
RJM MASTERMIND PBC/6X Manuel utilisateur
Atlas
Atlas MMK-KVM8 Manuel utilisateur
Cabletron Systems
Cabletron Systems GIGAswitch GSR-16 Manuel utilisateur