D-Link Nuclias DNH-100 Manuel utilisateur

www.dlink.com

Manual how to bind the

Switches into the Nuclias Connect

For Nuclias Connect Hardware DNH-100 Rev.A and Nuclias Connect Software DNC-100

For SWITCH Rev.F and Rev.G

To bind the switch into the Nuclias Connect please follow these steps.

1. Requirements

- DGS-1210 in Rev.F with firmware version 6.30.xx or higher

- DGS-1210 in Rev.G with firmware version 7.30.xx or higher

- DGS-1100V2 in Rev.A with 10 Ports and more with the

Firmware version 4.00b019 or higher

- DXS-1210 in Rev.B with Firmware version 2.01b10 or higher

- DNH-100 Nuclias Conenct Hub with the actual Firmware 1.2.1.7 or higher.

Or DNC-100 Nuclias Connect Software in the actual Version 1.2.1.3 or higher.

The firmware files and software you can download from our D-A-CH-BE-NE-LUX

web sites https://www.dlink.com or https://ftp.dlink.de

2. Preparations

Different to the DAP Access Points the switch must be pre-configured so far

that it got an IP-address from the DHCP-Server in the network or has a static

IP-address compatible to the network.

By default the switch has the static IP-address 10.90.90.90

with subnet mask 255.0.0.0

Change the TCP/IP of the network connection temporarily to configure the

switch.

Alternative or if you don’t know the IP-address of your switch you can use our

Software D-Link Network Assistant (DNA) to find it out or to change it.

See following screenshot.

www.dlink.com

You can download the DNA from

https://ftp.dlink.de/software/DNA/D-Link_Network_Assistant_DNA_40021_all_en.zip

With the PC mouse go over the switch entry and then click on IP on the right side.

Then you can change the IP-address of the switch.

Note:

In the following steps granting that you already made a setup in

your DNH-100 / DNC-100 (following named as NC) and have it in use

with DAP-models, so the NC has a basic setup already.

3. Call the setup of your NC and log-in.

We recommend to use the English setup because the translation in other

languages isn’t fine sometimes.

- Chose English.

- Enter the username admin and your configured Admin-password.

- If necessary enter the displayed CAPTCHA.

- Click onto Login.

www.dlink.com

4. On the left go to the menu Configuration and then Create Profile.

Upper-right click onto Add Network to create a new Switch-Profile.

Note:

Switches can’t be bound into AP-Profiles, also AP not into Switch-Profiles.

5. Create a newSite or chose an already existing Site, in this you added an Access

point profile and then add a new Network.

For this give (the site and) the Network a name and then click on Next.

www.dlink.com

6. - Chose the Country where the switch has to work.

- If necessary modify the Time Zone.

- Set a hook at Switch.

- At Series Supported you must mark the Switch-Type this you want to add.

- At Password you must enter the Admin-password this the switch has to get

from the NC-Profile as soon as it will be bound-in.

Click on Next.

7. Normally it is fine to use Layer 2.

Click on Next.

www.dlink.com

8. Upper-left click onto Discovery to let search for switches.

9. The available and compatible switches in the network will be found.

Mark the switch this you want to bind into the NC-Profile.

Enter the Admin-password this the switch actually has.

- The default Admin-password is admin.

- If you already have changed the Admin-password then enter this.

Click on Import to take over the marked swich into the NC-Profile.

www.dlink.com

Recommendation!!

For each switch create an own NC-Profile: An own Site or an already exiting site with an

own Network each.

Else it can become difficult because the NC displays all LAN ports of all switches in the

NC-profile like they are one switch.

Example: The LAN ports of three DGS-1210-10P will be listed as 30 ports –a

differentiation which port if from which switch won’t be so easy.

10. Click on Yes.

11. The displayed NC flickers a few times now.

Please what until this ends.

Click on Apply & Exit.

www.dlink.com

12. After 3-5 minutes the switch will be displayed in the Dashboard.

Click onto this…

… then the Status of the switch will be displayed.

Normally at this moment it is boarding.

Status is orange = Boarding

After additionally 3-5 minutes the Status is green = Connected

The switch can be managed and configured via the NC now.

www.dlink.com

13. To access the possible settings of the switch in the NC, on the left go to the

menu Configuration and then Profile Settings.

There inside the created profile of the switch you can make several settings.

With it the binding of the switch into the Nuclias Connect is finished.

Example:

Each a DGS-1210 Rev.F and G is bound into the Nuclias Connect:

www.dlink.com

Please see also the following manuals

Basic Setup of the DNH:

https://ftp.dlink.de/dnh/dnh-100/documentation/DNH-

100_howto_reva_Grundrichtung_de.pdf

The Nuclias Connect app:

https://ftp.dlink.de/dnh/dnh-100/documentation/DNH-

100_howto_reva_NucliasConnectApp_de.pdf

Tips:

https://ftp.dlink.de/dnh/dnh-100/documentation/DNH-100_howto_reva_Tipps_de.pdf

For further manuals please visit our FTP server

https://ftp.dlink.de/dnh/dnh-100/documentation/

and our websites

https://www.dlink.com/de/de

https://www.dlink.com/be/fr

https://www.dlink.com/be/nl

https://www.dlink.com/nl/nl

Autres manuels pour Nuclias DNH-100

Autres manuels D-Link Changer

D-Link

D-Link DGS-1016D - Switch Manuel utilisateur

D-Link

D-Link DGS-1016D/I2A Manuel utilisateur

D-Link

D-Link DGS-1016D - Switch Manuel utilisateur

D-Link

D-Link DGS-1005D - Switch Manuel utilisateur

D-Link

D-Link DUB-H7 - Hub - USB Manuel utilisateur

D-Link

D-Link DES-1016D - Switch Manuel utilisateur

D-Link

D-Link DGS-1210 Series Manuel utilisateur

D-Link

D-Link GO-SW-16GE Manuel utilisateur

D-Link

D-Link DU-H4 Manuel utilisateur

D-Link

D-Link DE-81 6TP Manuel utilisateur

D-Link

D-Link DGS-1224TP - Web Smart Switch Manuel utilisateur

D-Link

D-Link DGS-1210-10P Manuel utilisateur

D-Link

D-Link Nuclias DNH-100 Manuel utilisateur

D-Link

D-Link xStack DGS-3620 Series Manuel utilisateur

D-Link

D-Link Web Smart DES-1210-28 Manuel utilisateur

D-Link

D-Link DES-1024D Manuel utilisateur

D-Link

D-Link DKVM-222 Manuel utilisateur

D-Link

D-Link DXS-1100-16SC Manuel utilisateur

D-Link

D-Link DES-1005P Manuel utilisateur

D-Link

D-Link DES-1250G Manuel utilisateur

D-Link

D-Link DGS-1210/ME series Manuel utilisateur

D-Link

D-Link DGS-1210-28X/ME Manuel utilisateur

D-Link

D-Link DGS-1005P Manuel utilisateur

D-Link

D-Link DGS-3100-48 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Manuel utilisateur