CYP PU-607BDWP-TX Manuel utilisateur

PU-607BDWP-TX

HDMI over Single CAT5e/6/7 HDBaseT™ - Bi-Directional PoC

Wallplate Transmitter (Full 5Play™ & Single LAN up to 100m)

OPERATION MANUAL

DISCLAIMERS

The information in this manual has been carefully checked and is

believed to be accurate. CYP (UK) Ltd assumes no responsibility for any

infringements of patents or other rights of third parties which may result

from its use.

CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be

contained in this document. CYP (UK) Ltd also makes no commitment to

update or to keep current the information contained in this document.

CYP (UK) Ltd reserves the right to make improvements to this document

and/or product at any time and without notice.

No part of this document may be reproduced, transmitted, transcribed,

stored in a retrieval system, or any of its part translated into any language

or computer le, in any form or by any means—electronic, mechanical,

magnetic, optical, chemical, manual, or otherwise—without express

written permission and consent from CYP (UK) Ltd.

Version 1.1

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be

trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or operate

this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this

equipment:

• Always follow basic safety precautions to reduce the risk of re,

electrical shock and injury to persons.

• To prevent re or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts inside

the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the PSU if

it is damaged.

• Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or

openings in the unit housing that provide ventilation and allow for

sucient space for air to circulate around the unit.

REVISION HISTORY

VERSION NO. DATE SUMMARY OF CHANGE

v1.00 13/02/2014 First release

v1.01 31/03/2014 Corrected Contents List

v1.02 23/08/2019 Updated Specications

CONTENTS

1. Introduction...........................................6

2. Applications ...........................................6

3. Package Contents ..................................6

4. System Requirements ...........................6

5. Features..................................................7

6. Operation Controls and Functions.......8

6.1 Transmitter................................................... 8

6.2 Rear Panel..................................................... 9

6.3 IR Cable Pin Assignment ......................10

6.4. D-Sub 9-Pin Denitions........................10

7. Connection DiagramS ........................ 11

8. Specications...................................... 12

8.1 Technical Specications ........................12

8.1 Cable Specications ...............................13

9. Acronyms............................................. 14

1. INTRODUCTION

The PU-607BDWP-TX Wallplate Transmitter allows uncompressed HDMI

signals and IP data to be transmitted over a Single CAT5e/6/7 cable.

This solution has the added features of RS-232 and 2-way IR control

functionality over the same CAT5e/6/7 cable up to 100m/328ft at 1080p

and 70m/229ft at 4K.

This Transmitter is designed to be used with the PU-607BD-RX and PU-

607BDWP-RX Receivers only, which enables Bi-Directional Power over

Cable (PoC) functionality.

2. APPLICATIONS

Household entertainment sharing and control

Lecture room display and control

Showroom display and control

Meeting room presentation and control

Classroom display and control

3. PACKAGE CONTENTS

1×HDMI over Single CAT5e/CAT6 Transmitter

1×IR Blaster

1×IR Receiver

1×24V DC Power Adaptor

Operation Manual

4. SYSTEM REQUIREMENTS

Input HDMI source equipment such as DVD/Blu-ray player and HDMI

equipped output display (TV or monitor)with HDMI input jack.

5. FEATURES

HDMI 1.x and DVI 1.0 compliant

HDCP compliant

Supports HDMI 3D and 4K x 2K features

Supports HDCP repeater and CEC bypass

Supports distance up to 100m/328ft at 1080p and 70m/229ft at 4K

through CAT5e/6/7 cable

HDMI input resolutions up to 4K@60Hz (YUV 4:2:0, 8-bit) or 4K@30Hz

( YUV 4:4:4, 8-bit)

Supports pass-through of audio formats including LPCM 2.0/5.1/7.1,

and Bitstream over HDMI

5Play™ convergence: HDMI, bi-directional PoC, (bi-directional IR &

RS232) & LAN

Wall-plate design and installation Friendly

Note

1. This system was tested with CAT6/23AWG and CAT5e/24AWG cable, so if

using cables of another type, results may vary.

2. For playback of 4K2K HDMI source signals, a 4K2K capable display and

High Speed HDMI cables are required.

3. Only compatible with PU-607BD-TX & PU-607BDWP-TX Receivers

6. OPERATION CONTROLS AND FUNCTIONS

6.1 Transmitter

HDMI INLAN

POWER

LINK

IR 2

EXTENDER

IR 1

BLASTER

DC 24V

RS-232

1 2

3 4 5 6 7 8

1IR 2 EXTENDER: Connect to the supplied IR Extender cables for IR

signal reception. Ensure that remote being used is within the direct

line-of-sight of the IR Extender.

2DC 24V: Connect the power adaptor included in the package

and then connect to AC power to activate the device.

3IR 1 BLASTER: Connect to the supplied IR Blaster cable for IR

signal transmission. Place the IR Blaster in direct line of sight of the

equipment to be controlled.

4RS-232 IN: Connect to a PC or Laptop with D-Sub 9 pin male cable for

the transmission of RS-232 commands.

5LAN: Connect to an internet or network connection.

When the Transmitter or any compatible LAN equipped Receivers are

connected to a network, this allows the network access (including

internet access if available) to be shared between the Transmitter and

all connected Receivers. Connect any Ethernet equipped device e.g.

a Smart TV or games console to the LAN port of a receiver for that

device to share the network/internet access.

6HDMI IN: This slot is to connect with HDMI source equipment such

as DVD/Blu-ray player with HDMI source signal.

7Power LED: This LED will illuminate when the device is connected to a

power supply.

8LINK LED: This LED will illuminate when both the input source and

output display signals are connected through the CAT cable. When it

blinks regularly it indicates the source is NOT sending a signal to the

Transmitter but the Transmitter and Receiver are linked and if it blinks

irregularly it indicates an error has occurred.

6.2 Rear Panel

1CAT OUT: Connect to the Receiver unit with a single CAT5e/6/7 cable

for transmission of all data signals.

6.3 IR Cable Pin Assignment

1Power 3.3V

IR Blaster Signal

IR Signal

Power 3.3V

Ground

IR Extender

IR Blaster

6.4. D-Sub 9-Pin Denitions

Pin Dene TX/RX

1N/C

2TxD/RxD

3RxD/TxD

4N/C

5GND

6N/C

7N/C

8N/C

9N/C

Table des matières

Autres manuels CYP Extenseur

CYP

CYP CH-1107EX Manuel utilisateur

CYP

CYP CH-1106TX & RX Manuel utilisateur

CYP

CYP CH-1529TXPL Manuel utilisateur

CYP

CYP PUV-1230PL-RX Manuel utilisateur

CYP

CYP PU-1109KIT Manuel utilisateur

CYP

CYP PU-1106-KIT Manuel utilisateur

CYP

CYP PUV-1510RX Manuel utilisateur

CYP

CYP CH-1601TXRX Manuel utilisateur

CYP

CYP CH-1602TX Manuel utilisateur

CYP

CYP CLUX-SDI2OF Manuel utilisateur

CYP

CYP Suprex SPX-7400 Series Manuel utilisateur

CYP

CYP CH-514RXL Manuel utilisateur

CYP

CYP CDVI-1109TXC Manuel utilisateur

CYP

CYP CH-506RX Manuel utilisateur

CYP

CYP SDV-FTX Manuel utilisateur

CYP

CYP PU-507TX-HDVGA Manuel utilisateur

CYP

CYP CDVI-513TXL Manuel utilisateur

CYP

CYP PU-1107-KIT Manuel utilisateur

CYP

CYP CH-506TX Manuel utilisateur

CYP

CYP PU-1107-KIT Manuel utilisateur

CYP

CYP CH-506TXPLRXPL Manuel utilisateur

CYP

CYP CH-513TXL Manuel utilisateur

CYP

CYP PU-USB-AL Manuel utilisateur

CYP

CYP CH-506TX Manuel utilisateur

Manuels Extenseur populaires d'autres marques

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

SC&T

SC&T HE03-4K Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

MuxLab

MuxLab 500771 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur