Clarke CHT877 Manuel utilisateur

USER INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC0518 ISS 1

LAZY TONGS RIVET GUN

MODEL NO: CHT877

PART NO: 1801877

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Rivet Gun. Before attempting to use this

product, please read this manual thoroughly and follow the instructions

carefully. In doing so you will ensure the safety of yourself and that of others

around you and you can look forward to your purchase giving you long and

satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission. This guarantee does not effect your

statutory rights.

FITTING AND STORING THE NOZZLES

The CHT877 rivet gun is equipped with a choice of 5 different size nozzles to suit

different rivets. Choose the rivet to be used for the job.

The sizes available are:

• 3/32” (2.4 mm)

• 1/8” (3.2 mm)

• 5/32” (4.0 mm)

• 3/16” (4.8 mm)

• 1/4” (6.4 mm)

NOTE: The dimensions are

engraved on each one.

1. Screw your chosen nozzle into the tip of the rivet gun, finger tight.

2. Always store the unused nozzles by screwing them back into the rivet gun

for safe keeping.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OPERATION

1. When items are to be riveted

together, the hole diameter must

be nominally larger than the outer

diameter of the rivet. Ensure that

the hole is perpendicular with the

surface of the workpiece

components.

2. Insert the rivet into the hole of the

workpiece components.

3. Pull the handle back to extend

the rivet gun to its full length.

• This will enable the rivet stem to

enter the rivet gun as far as it will

go, with the handle fully

extended.

4. Ensure the rivet gun is

perpendicular to the work piece

and the flange of the rivet is

pressed against it.

5. Push the rivet gun handle fully

forward to expand the rivet.

6. If the rivet stem does not break off

at the first stroke, pull back the

handle and repeat step 6.

7. Extend the rivet gun by pulling the

handle back and the broken stem

should be ejected from the

nozzle.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ADJUSTMENT

If the internal claws of the rivet gun

fail to grip the stem of the rivet, the

gun will need adjusting.

1. Loosen the locking nut and rotate

the gun shield clockwise to

tighten (anti-clockwise to loosen).

2. Pull the handle to extend the

riveter and to tighten the internal

claws.

3. Re-tighten the locking nut.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Clarke Outils

Clarke

Clarke CONTRACTOR CLJ120 Mode d’emploi

Clarke

Clarke CMC36B Manuel utilisateur

Clarke

Clarke CHT738 Mode d’emploi

Clarke

Clarke CAT151 Manuel d'installation et d'exploitation

Clarke

Clarke CAT125 Manuel d'installation et d'exploitation

Clarke

Clarke METALWORKER CMSSCS Manuel utilisateur

Clarke

Clarke KIT1100 Mode d’emploi

Clarke

Clarke CAR8P Manuel utilisateur

Clarke

Clarke CHT878 Manuel utilisateur

Clarke

Clarke CHT172 Manuel utilisateur

Clarke

Clarke SBR305 Mode d’emploi

Clarke

Clarke CAT33B Manuel d'installation et d'exploitation

Clarke

Clarke CDS300B Manuel utilisateur

Clarke

Clarke CHT718 Manuel utilisateur

Clarke

Clarke X-pro CAT164 Manuel d'installation et d'exploitation

Clarke

Clarke CHT706 Manuel utilisateur

Clarke

Clarke CAR15PC Manuel utilisateur

Clarke

Clarke CAT29B Manuel d'installation et d'exploitation

Clarke

Clarke CHT403 Manuel utilisateur

Clarke

Clarke Metalworker CPTN1 Mode d’emploi

Clarke

Clarke X-PRO CAT170 Manuel d'installation et d'exploitation

Clarke

Clarke Air CHR9P Manuel utilisateur

Clarke

Clarke CAT218 Manuel d'installation et d'exploitation

Clarke

Clarke CHT637 Manuel d'installation et d'exploitation

Manuels Outils populaires d'autres marques

Martor

Martor SECUNORM 175 Manuel utilisateur

ERKCO

ERKCO 1000 Manuel utilisateur

jbc

jbc N4473 Manuel utilisateur

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuel utilisateur

Worx Professional

Worx Professional Sonicrafter WU676 Manuel utilisateur

Gage Bilt

Gage Bilt GB713SH Manuel utilisateur

Hilti

Hilti DX 9-ENP Manuel utilisateur

norbar

norbar NORTRONIC 34399 Manuel utilisateur

BGS technic

BGS technic 8578 Manuel utilisateur

Makita

Makita DHR241 Manuel utilisateur

Motor Guard

Motor Guard JMB-1250 Manuel utilisateur

Power Adhesives

Power Adhesives 805-12 Manuel utilisateur

Clemco

Clemco 24189 Manuel utilisateur

VVG

VVG VNG 903 Series Manuel utilisateur

Hilti

Hilti FX 3-A Manuel utilisateur

Grizzly

Grizzly H6472 Manuel utilisateur

axing

axing BWZ 5-02 Manuel utilisateur

Dh-Robotics

Dh-Robotics RGI-100 Comment utiliser