Clarke CHT878 Manuel utilisateur

USER INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC0518 ISS 1

HAND RIVETER WITH STEM

COLLECTION TANK

MODEL NO: CHT878

PART NO: 1801878

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Hand Riveter with stem collection tank.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you and you can look forward to your purchase

giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission. This guarantee does not effect your

statutory rights.

FITTING AND STORING THE NOZZLES

Choose the rivet to be used for the job. The CHT878 Hand Riveter is equipped

with a choice of 5 different size nozzles to suit different rivets.

The sizes available are:

• 3/32” (2.4 mm)

• 1/8” (3.2 mm)

• 5/32” (4.0 mm)

• 3/16” (4.8 mm)

• 1/4” (6.4 mm)

NOTE: The dimensions are

engraved on each one.

• Always store the unused nozzles by screwing them back into the stem

collector of the riveter for safe keeping.

Screw your chosen nozzle into the tip of the rivet gun, finger tight.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OPERATION

1. When items are to be riveted

together, the hole diameter must

be nominally larger than the outer

diameter of the rivet. Ensure the

hole is perpendicular with the

surface of the workpiece

components.

2. Insert the rivet into the hole in the

workpiece.

3. Open the arms of the riveter as

wide as possible.

• This will enable you to insert the

rivet stem into the riveter as far as

it will go.

4. Ensure that the riveter is

perpendicular to the workpiece

and the flange of the rivet is

pressed against it.

5. Close the handles together to

expand the rivet.

6. If the rivet stem does not break at

the first stroke, open the handles

and repeat until the components

are squeezed tightly together and

the rivet stem breaks off.

7. The broken stem should be

ejected from the nozzle and be

caught in the collection tank.

8. Unscrew the collection tank and

dispose of the contents when full.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ADJUSTMENT

If the internal claws of the rivet gun

fail to grip the stem of the rivet, the

riveter will need adjusting.

1. Loosen the locking nut and rotate

the riveter shield clockwise to

tighten (anti-clockwise to loosen).

2. Open the handles to relax the

riveter and to tighten the internal

claws.

3. Re-tighten the locking nut.

Table des matières

Autres manuels Clarke Outils

Clarke

Clarke CONTRACTOR CSJ100 Mode d’emploi

Clarke

Clarke CMC36B Manuel utilisateur

Clarke

Clarke CHT718 Manuel utilisateur

Clarke

Clarke CHT172 Manuel utilisateur

Clarke

Clarke CHT706 Manuel utilisateur

Clarke

Clarke CMFT250 Mode d’emploi

Clarke

Clarke CAT29B Manuel d'installation et d'exploitation

Clarke

Clarke SBR610 Mode d’emploi

Clarke

Clarke Metalworker CPTN1 Mode d’emploi

Clarke

Clarke CEA150 Manuel d'installation et d'exploitation

Clarke

Clarke Air CHR9P Manuel utilisateur

Clarke

Clarke CBS4 Manuel utilisateur

Clarke

Clarke CHT738 Mode d’emploi

Clarke

Clarke CONTRACTOR CWJ700 Mode d’emploi

Clarke

Clarke METALWORKER CMSSCS Manuel utilisateur

Clarke

Clarke CFC100 Manuel d'installation et d'exploitation

Clarke

Clarke CHT697 Guide d'installation

Clarke

Clarke CAR15PC Manuel utilisateur

Clarke

Clarke CAT114 Mode d’emploi

Clarke

Clarke CHT637 Manuel d'installation et d'exploitation

Clarke

Clarke CMFT220 Mode d’emploi

Clarke

Clarke CAT216 Manuel d'installation et d'exploitation

Clarke

Clarke Air CAT62 Manuel d'installation et d'exploitation

Clarke

Clarke CHT 141 Manuel utilisateur

Manuels Outils populaires d'autres marques

Martor

Martor SECUNORM 175 Manuel utilisateur

ERKCO

ERKCO 1000 Manuel utilisateur

jbc

jbc N4473 Manuel utilisateur

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuel utilisateur

Worx Professional

Worx Professional Sonicrafter WU676 Manuel utilisateur

Gage Bilt

Gage Bilt GB713SH Manuel utilisateur

Hilti

Hilti DX 9-ENP Manuel utilisateur

norbar

norbar NORTRONIC 34399 Manuel utilisateur

BGS technic

BGS technic 8578 Manuel utilisateur

Makita

Makita DHR241 Manuel utilisateur

Motor Guard

Motor Guard JMB-1250 Manuel utilisateur

Power Adhesives

Power Adhesives 805-12 Manuel utilisateur

Clemco

Clemco 24189 Manuel utilisateur

VVG

VVG VNG 903 Series Manuel utilisateur

Hilti

Hilti FX 3-A Manuel utilisateur

Grizzly

Grizzly H6472 Manuel utilisateur

axing

axing BWZ 5-02 Manuel utilisateur

Dh-Robotics

Dh-Robotics RGI-100 Comment utiliser