Clarke CAT138 Manuel d'installation et d'exploitation

OPERATING & MAINTENANCE

INSTRUCTIONS

GC064

AIR HAMMERS

MODEL NO: CAT138/CAT139

PART NO: 3120152 /3120153

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Air Hammer. Before attempting to use

this product, please read this manual thoroughly and follow the instructions

carefully. In doing so you will ensure the safety of yourself and that of others

around you, and you can look forward to your purchase giving you long and

satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission. This guarantee does not effect your

statutory rights.

SPECIFICATIONS

Please note that the details and specifications contained herein are correct

at the time of going to print. However Clarke International reserve the right to

change specifications at any time without prior notice.

CAT138 CAT139

Maximum Operating Pressure 90 psi (6.2 bar)

Air Consumption (under load) 14 cfm 12 cfm

Max Blows per Min. 3300 4500

Air Inlet Size 1/4” BSP thread

Vibration Levels 10.6 m/s2

Sound pressure level 98 dB A

Sound power level 111 dB LWA

Dimensions (L x W x H) 190 x170 x 50 mm 190 x 55 x 150 mm

Weight 2.4 kg 2.2 kg

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GENERAL SAFETY RULES

WORK ENVIRONMENT

1. Keep the work area clean and tidy.

2. Dress appropriately - Do not wear loose clothing or jewellery. Tie long hair

out of the way.

3. Keep children and visitors away - Do not let children handle the tool.

USE

1. Stay alert and use common sense - do not operate this tool when you are

tired or under the influence of alcohol, drugs or medication.

2. Always wear eye protectors when using air tools. Eye protectors must

provide protection from flying particles from the front and the side.

3. Always wear ear protectors and a dust mask when using an air hammer.

4. Do not overreach - keep proper footing and balance at all times.

5. Do not fit the tool to any stand or clamping device that may damage it.

6. Never use oxygen, CO2, combustible gases, or any bottled gas, as a

source of power for the grease gun. This product should only be used with

a suitably rated compressed air supply.

7. Do not connect the air hose with your finger on the trigger of the tool.

8. Keep the air supply hose away from heat, oil and sharp edges.

9. Do not exceed the maximum pressure for the tool of 90 psi / 6.2 bar.

10. Check hoses for leaks or excessive wear before use, and ensure that all

connections are secure.

11. Do not use the tool for any other purpose than described in this manual.

12. Do not carry out any alterations or modifications to the tool.

13. Always disconnect from the air supply when:

• Performing any maintenance.

• The tool is not in use.

• The tool will be left unattended.

CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN

PERSONAL INJURY, AND/OR DAMAGE TO PROPERTY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

• Moving to another work area.

• Passing the tool to another person.

14. This tool should be serviced at regular intervals by qualified personnel.

15. Avoid damaging the tool by applying excessive force of any kind.

16. Always maintain the tool with care. Keep it clean for the best and safest

performance.

17. Do not force or misuse the tool. It will do a better and safer job at the rate

for which it was designed.

18. This tool vibrates with use. Vibration may be harmful to your hands or arms.

Stop using the tool if discomfort, a tingling feeling or pain occurs. Seek

medical advice before resuming use.

19. Never carry an air tool by the air supply hose.

20. Never carry an air tool with your finger on the trigger.

AIR HAMMER SPECIFIC HAZARDS

1. Only use accessories designed for use with this power tool.

2. Never use any of the chisels supplied as hand struck tool.

3. Never use blunt chisels which require excessive pressure and can break

from fatigue. Always use sharp tools.

4. Never mis-use the tool by prising which can result in a broken tool.

5. Ensure there are no hidden electrical cables, gas pipes etc, which could

cause a hazard if damaged by action of the chisels.

IMPORTANT

Please read all of the safety and operating instructions carefully before using

this product. The following safety symbols are to be found on the machine.

Keep these instructions in a safe place for future reference.

Read this instruction

booklet carefully

before use.

Wear ear protection

Wear eye protection Wear dust mask.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

COMPRESSED AIR REQUIREMENTS

• Use only clean, dry, regulated compressed air as a power source.

• Air compressors used with the tool must comply with the appropriate

European Community Safety Directives.

• A build-up of moisture or oil in the air compressor will accelerate

wear and corrosion in the tool. ensure any moisture is drained from

the compressor daily and the inlet filter is kept clean.

• If an unusually long air hose is required, (over 8 metres), the line

pressure or the hose inside diameter may need to be increased.

• The air hose must be rated at least 150% of the maximum operating

pressure of the tool.

• A typical air line layout is shown above. If an automatic in-line filter/

regulator is used, it will keep the tool in good condition, but should

be regularly checked & topped up with oil. Clarke air-line oil should

be used, and the lubricator adjusted to approx 2 drops per minute.

• Never exceed the maximum operating pressure for the tool. It is

recommended that air pressure to this tool does not exceed 90 psi

at the tool when running. Higher pressures and unclean air will

shorten the life of the tool due to faster wear and is a possible safety

hazard.

WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU

ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF

COMPRESSORS AND A COMPRESSED AIR SUPPLY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OVERVIEW

OPERATION

NOTE: Ensure the compressed air supply is turned off.

1. If required, connect an in-line mini oiler to the tool.

• A mini oiler helps to prolong the life of the air tool. Read the

instructions supplied with the mini-oiler before use.

NOTE: If a mini-oiler is not being used, insert a few drops of oil into the tool

through the air inlet before use.

NO DESCRIPTION NO DESCRIPTION

1 Retaining spring 3 Air Inlet

2 Trigger 4 Chisel Set (CAT138-5 chisels/

CAT139-4 chisels)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

2. Connect a suitable hose as shown.

3. Connect the other end of the hose

to the compressed air supply.

4. Turn on the air supply and check

for air leaks. Rectify any found

before proceeding.

• PTFE tape may be helpful for

sealing threaded connections.

5. Your air tool is now ready for use.

FITTING THE CHISEL

1. First remove the retaining spring

from the nose by unscrewing it.

• Use the inboard lug to gain

purchase.

2. Insert the chisel into the air

hammer as shown.

3. Replace the retaining spring as

shown.

• Use the lugs to tighten.

USING THE AIR HAMMER

1. Hold the tool firmly, then bring the

tool towards the work at an angle

of approximately 60-70 degrees.

2. Pull the trigger with the chisel in

light contact with the work.

3. Move slowly across the work

surface. To remove scale, rust or

other contaminants, only a light

force should be required.

4. Release the trigger to stop operation, whilst maintaining contact with the

work.

NOTE: that the tool may impact briefly after the trigger is released.

NOTE: The retaining spring has a life expectancy, depending upon the

intensity of usage. It is recommended that you procure a spare

spring for use in the event of failure occurring during the course of

a particular job.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

DISCONNECTING THE AIR SUPPLY

Do not disconnect the air supply hose until the air supply has been shut down

and the compressed air pressure released.

1. Refer to the compressor instruction manual for the procedure to shut down

and release the compressed air.

2. Once the pressure has been released, disconnect the air supply hose from

the air tool.

3. Store the tool safely in its box in a dry, secure environment.

TROUBLESHOOTING

ACCESSORIES

A wide range of airline accessories is available including filter/regulators,

lubricators, high-pressure hoses (5 to 50 metres) etc.

Contact your Clarke dealer or Clarke International Service Department for

further information.

SYMPTOM PROBLEM SOLUTION

Tool runs slowly or will

not operate.

Dirt or gum in the tool Flush the tool with air line oil

or gum solvent.

Air hose leaks. Tighten and seal hose

fittings with teflon tape.

Low air pressure. Adjust compressor

regulator to 90 psi. Check

the hose is the correct size

and length.

No oil in tool Lubricate the tool.

Worn rotor blades. Return to Clarke dealer for

repair.

Water in airline. Drain air receiver and/or in-

line filter. Run tool until clear

of water. Oil tool again.

Tool will not shut off. O-rings damaged or ill-

fitting in seat.

Return to Clarke dealer for

repair.

Tool runs erratically. Cylinder may have

come loose from the

housing.

Tighten cylinder or return to

Clarke dealer.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

MAINTENANCE

DAILY

1. Before use, drain any water from the compressed air supply.

2. This air tool should be lubricated before use. Turn the tool upside down and

pour 1-2 drops of Clarke air-line oil into the air inlet. This should be carried

out regardless of whether or not an in-line mini oiler is used. If an in-line mini

oiler is not used, this procedure should be repeated after every two to

three hours of constant use.

CLEANING

1. Keep all parts of the tool clean.

2. Deposits in the tool may also reduce efficiency. This can be corrected by

cleaning the air inlet and flushing out the tool with gum solvent, or failing

this, the tool should be disassembled, thoroughly cleaned, dried and

reassembled.

3. If the tool becomes inefficient and the air supply is of good quality, it may

be necessary to replace worn or damaged parts. You may prefer to take

the tool to your Clarke dealer if internal maintenance is required.

Your Clarke air tool has been designed to give long and trouble free service. If,

however, having followed the instructions in this booklet carefully, you

encounter problems, take the unit to your local Clarke dealer.

PERFORMANCE

Please note that factors other than the tool may effect its operation and

efficiency such as reduced compressor output, excessive drain on the airline,

moisture or restrictions in the air-line, or the use of connectors of improper size

or poor condition which will reduce air supply.

**Clarke Air-line Oil (part no. 3050825) is available from your Clarke dealer.

STORAGE

If the tool is to be stored, or is idle for longer than 24 hours, run a few drops of

Clarke air-line oil into the air inlet and run the tool in order to lubricate the

internal parts. When not in use, disconnect the tool from the air supply, clean

and store in a safe, dry place.

WARNING: MAKE SURE THAT THE AIR TOOL IS DISCONNECTED FROM THE

AIR SUPPLY BEFORE STARTING ANY CLEANING, OR MAINTENANCE

PROCEDURES.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

PARTS LIST & DIAGRAM

No Description No Description

1 Housing 16 Trigger

2 Housing Cover 17 Roll Pin

3Screw 18Plug

4EndCover 19OIlSeal

5Washer 20Pin

6 Rear Plate 21 Pin Cover

7 Valve 22 Spring

8 Set Pin 23 O-Ring

9 Front Plate 24 Air Inlet

10 Piston 25 Muffler

11 Cylinder 26 Screw

12 Retaining Spring 27 Soft Grip-Front

13 Trigger Sleeve 28 Soft Grip-Rear

14 Spring 29 Chisel

15 O-Ring

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Clarke Outils

Clarke

Clarke CHT 141 Manuel utilisateur

Clarke

Clarke X-PRO CAT170 Manuel d'installation et d'exploitation

Clarke

Clarke CRT 40 Manuel utilisateur

Clarke

Clarke CFC100 Manuel d'installation et d'exploitation

Clarke

Clarke CHT878 Manuel utilisateur

Clarke

Clarke CHT718 Manuel utilisateur

Clarke

Clarke CAR15PC Manuel utilisateur

Clarke

Clarke CHT733 Manuel utilisateur

Clarke

Clarke CAT29B Manuel d'installation et d'exploitation

Clarke

Clarke Strong-Arm CFB600 Manuel utilisateur

Clarke

Clarke CAT33B Manuel d'installation et d'exploitation

Clarke

Clarke CAT66 Manuel utilisateur

Clarke

Clarke GWH8 Mode d’emploi

Clarke

Clarke CHT 455 Manuel utilisateur

Clarke

Clarke Metalworker CPTN1 Mode d’emploi

Clarke

Clarke CHT 454 Manuel utilisateur

Clarke

Clarke CHT637 Manuel d'installation et d'exploitation

Clarke

Clarke TPG30P Manuel utilisateur

Clarke

Clarke CAT151 Manuel d'installation et d'exploitation

Clarke

Clarke CAT120 Mode d’emploi

Clarke

Clarke CAT33B Manuel d'installation et d'exploitation

Clarke

Clarke CAT125 Manuel d'installation et d'exploitation

Clarke

Clarke Air CHR9P Manuel utilisateur

Clarke

Clarke CAT218 Manuel d'installation et d'exploitation

Manuels Outils populaires d'autres marques

Martor

Martor SECUNORM 175 Manuel utilisateur

ERKCO

ERKCO 1000 Manuel utilisateur

jbc

jbc N4473 Manuel utilisateur

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuel utilisateur

Worx Professional

Worx Professional Sonicrafter WU676 Manuel utilisateur

Gage Bilt

Gage Bilt GB713SH Manuel utilisateur

Hilti

Hilti DX 9-ENP Manuel utilisateur

norbar

norbar NORTRONIC 34399 Manuel utilisateur

BGS technic

BGS technic 8578 Manuel utilisateur

Makita

Makita DHR241 Manuel utilisateur

Motor Guard

Motor Guard JMB-1250 Manuel utilisateur

Power Adhesives

Power Adhesives 805-12 Manuel utilisateur

Clemco

Clemco 24189 Manuel utilisateur

VVG

VVG VNG 903 Series Manuel utilisateur

Hilti

Hilti FX 3-A Manuel utilisateur

Grizzly

Grizzly H6472 Manuel utilisateur

axing

axing BWZ 5-02 Manuel utilisateur

Dh-Robotics

Dh-Robotics RGI-100 Comment utiliser