Cisco NCS 1004 Manuel utilisateur

Safety Guidelines

Before you perform any procedure in this publication, you must review the safety guidelines in this section

to avoid injuring yourself or damaging the equipment. Note that this section contains guidelines, and does

not include every potentially hazardous situation. During any installation procedure, always use caution and

common sense.

Review the complete list of safety warnings available at Regulatory Compliance and Safety Information for

Cisco NCS 1004 Series.

•Standard Warning Statements, on page 1

•General Safety Guidelines for Personal Safety and Equipment Protection, on page 2

•Safety Precaution for Module Installation and Removal, on page 2

•Safety with Electricity, on page 3

•Power Connection Guidelines , on page 3

•Safety Precaution for Energy Hazard, on page 4

•Safety Precaution for Laser Radiation, on page 4

•Prevent Electrostatic Discharge Damage , on page 5

•NEBS Regulatory Compliance Statements, on page 6

Standard Warning Statements

This unit is intended for installation in restricted access areas. A restricted access area can be accessed

only by using a special tool, lock and key, or other means of security.Statement 1017

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Warning

Hazardous voltage or energy may be present on power terminals. Always replace cover when terminals

are not in service. Be sure uninsulated conductors are not accessible when cover is in place. Statement

1086

Warning

Safety Guidelines

Mount the device on a rack that is permanently affixed to the building.Statement 1049

Warning

Ultimatedisposalofthisproductmustbehandledaccordingtoallnationallawsandregulations.Statement

1040

Warning

General Safety Guidelines for Personal Safety and Equipment

Protection

Follow these safety guidelines:

• Never attempt to lift an object that might be too heavy for you to lift by yourself.

• Always unplug power cables when performing maintenance or working on the chassis, unless the

replacement part is hot swappable and designed for online insertion and removal (OIR).

• Keep the work area clear and dust free during and after installation.

• Keep tools and chassis components away from walkways and equipment rack aisles.

• Do not wear loose clothing, jewelry (including rings and chains), or other items that could get caught in

the equipment.

• Fasten your tie or scarf and sleeves.

• Operate Cisco equipment safely by using it in accordance with its electrical ratings and product usage

instructions.

• Do not work alone if potentially hazardous conditions exist.

• Ensure that the installation of the router is in compliance with national and local electrical codes: in the

United States, National Fire Protection Association (NFPA) 70, United States National Electrical Code;

in Canada, Canadian Electrical Code, part I, CSA C22.1; in other countries, International Electrotechnical

Commission (IEC) 364, part 1 through part 7.

Safety Precaution for Module Installation and Removal

Ensure to observe the following safety precautions when you are working with the chassis modules.

Invisible laser radiations present.Statement 1016

Warning

Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams

or view directly with optical instruments.Statement 1051

Warning

Safety Guidelines

General Safety Guidelines for Personal Safety and Equipment Protection

Safety with Electricity

Before working on a chassis or with power supplies, unplug the power cord on AC units. Disconnect

the power at the circuit breaker on DC units.Statement 12

Warning

Beforeworkingonequipmentthatisconnectedtopowerlines,removejewelry(including rings, necklaces,

and watches). Metal objects heat up when connected to power and ground and can cause serious burns

or weld the metal object to the terminals.Statement 43

Warning

Avoid using or servicing any equipment that has outdoor connections during an electrical storm. There

may be a risk of electric shock from lightning. Statement 1088

Warning

This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the

absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority

or an electrician if you are uncertain that suitable grounding is available.Statement 1024

Warning

This unit may have more than one power supply connection. All connections must be removed to

de-energize the unit.Statement 1028

Warning

Wheninstalling or replacingthe unit,ensurethe ground connection firstand disconnected last. Statement

1046

Warning

Thisequipment is intended to be groundedtocomply with emission and immunity requirements.Ensure

that the switch functional ground lug is connected to earth ground during normal use. Statement 1064

Warning

Power Connection Guidelines

Check the power at your site to ensure you are receiving clean power (free of spikes and noise).

Ensure to observe the following safety guidelines while connecting the device power supplies.

Safety Guidelines

Safety with Electricity

Never defeat the ground conductor or operate the equipment in the absence of a suitably installed

ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are

uncertain that suitable grounding is available. Statement 1024

Warning

Use copper conductors only. Statement 1025

Warning

This product requires short-circuit (overcurrent) protection, to be provided as part of the building

installation. Install only in accordance with national and local wiring regulations. Statement 1045

Warning

Safety Precaution for Energy Hazard

Do not reach into a vacant slot when installing or removing a module. Exposed circuitry is an energy

hazard.Statement 206

Warning

The Cisco NCS 1004 can be configured for a DC power source. Do not touch terminals with body parts or

conductive objects while they are energized.

Safety Precaution for Laser Radiation

Cisco NCS 1004 is classified as Hazard Level 1M as per IEC 60825-2 and Laser Class 1/1M as per IEC

60825-1, since it may include Class 1 or Class 1M Laser sources.

Figure 1: Class 1M Laser Product Label

Safety Guidelines

Safety Precaution for Energy Hazard

Figure 2: Class 1M Laser Product Label

Statement 291

Warning

Invisible laser radiations present.Statement 1016

Warning

Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams

or view directly with optical instruments.Statement 1051

Warning

Prevent Electrostatic Discharge Damage

Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. ESD may occur when

electronic printed circuit cards are improperly handled and can cause complete or intermittent failures. When

removing and replacing modules, always follow these ESD prevention procedures:

• Ensure that the device chassis is electrically connected to earth ground.

• Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact.

• Handle components by only their handles or edges; do not touch the printed circuit boards or connectors.

• Avoid contact between the printed circuit boards and clothing. The wrist strap only protects components

from ESD voltages on the body; ESD voltages on clothing can still cause damage.

Safety Guidelines

Prevent Electrostatic Discharge Damage

NEBS Regulatory Compliance Statements

The NEBS-GR-1089-CORE regulatory compliance statements and requirements are discussed in this section.

The intra-building port(s) (Management Ethernet Ports) of the equipment or subassembly must use

shielded intra-building cabling/wiring that is grounded at both ends. Statement 7003

Warning

The intra-building port(s) (Management Ethernet Ports) of the equipment or subassembly is suitable

for connection to intra-building or unexposed wiring or cabling only. The intra-building port(s) of the

equipment or subassembly must not be metallically connected to interfaces that connect to the OSP or

its wiring for more than 6 meters (approximately 20 feet). These interfaces are designed for use as

intra-building interfaces only (Type 2, 4, or 4a ports as described in GR-1089) and require isolation

from the exposed OSP cabling. The addition of Primary Protectors is not sufficient protection in order

to connect these interfaces metallically to an OSP wiring system. Statement 7005

Warning

Productsthat haveACpowerports that areintendedfordeployments wherean externalSurgeProtective

Device (SPD) is utilized at the AC power service equipment (see definition in National Electric Code).

Statement 7012

This product is designed for a Common Bonding Network (CBN) installation. Statement 7013

This product can be installed in network telecommunication facilities or locations where the National

Electric Code applies. Statement 8015 and 8016

The DC return connection to this system should remain isolated from the system frame and chassis

(DC-I). Statement 7016

Safety Guidelines

NEBS Regulatory Compliance Statements

Autres manuels pour NCS 1004

Table des matières

Autres manuels Cisco Matériel réseau

Cisco

Cisco ONS 15200 Series Manuel utilisateur

Cisco

Cisco Wide Area Application Engine 612 Manuel

Cisco

Cisco FirePOWER 8000 Series Manuel utilisateur

Cisco

Cisco DOC 785983 Manuel utilisateur

Cisco

Cisco MERAKI MX75 Manuel utilisateur

Cisco

Cisco 2600 Series Document technique

Cisco

Cisco AIR-WLC2106-K9 - Wireless LAN Controller... Manuel utilisateur

Cisco

Cisco Firepower 1010 Manuel utilisateur

Cisco

Cisco ASR 5500 Manuel utilisateur

Cisco

Cisco Catalyst X6148 Manuel utilisateur

Cisco

Cisco 1230AG - Aironet - Wireless Access Point Manuel utilisateur

Cisco

Cisco Network Adapter VIP-FE-TX/4E Manuel de l'opérateur

Cisco

Cisco WAE-674-K9 - Wide Area Application Engine... Manuel

Cisco

Cisco ONS 15454 DWDM Manuel utilisateur

Cisco

Cisco PIX Series Manuel

Cisco

Cisco IAD1101 Manuel utilisateur

Cisco

Cisco IAD2430 Series Guide d'installation

Cisco

Cisco NCS 540 Manuel utilisateur

Cisco

Cisco Firepower 1010 Manuel utilisateur

Cisco

Cisco Content Engine 510 Manuel utilisateur

Cisco

Cisco NCS 1001 Manuel

Cisco

Cisco ONS 15216-MD-40-ODD Manuel utilisateur

Cisco

Cisco ISE - Line Card ISE Manuel utilisateur

Cisco

Cisco CGR 1240 Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur