Cisco Edge 300 Series Guide de démarrage rapide

Last updated on October 15, 2015

Edge300FirmwareUpgrade

Introduction

This guide outlines the steps to upgrade the firmware on the Cisco Edge 300 and will be described in two

stages:

Preparing a bootable USB drive containing the desired Edge 300 firmware

Flashing the firmware onto the Edge 300 device

Prerequisites

Cisco Edge 300 device

1 USB flash drive formatted in FAT32 file system (minimum 2GB free space)

1 Edge 300 firmware image file (for use with the USB flash drive)

1 paper clip / SIM eject tool (for the recessed reset button)

Note:

Empty the contents of the USB flash drive for the purpose of Edge firmware flashing. The process

of creating a bootable flash drive will temporarily render it unusable for conventional storage and

transferring of files. The flash drive can later be reformatted back to its original file system once the

firmware upgrade has completed.

PreparingaBootableUSBDrive

1. From your computer, copy the Edge 300 firmware image into the root directory of the USB flash

drive. Disconnect the USB drive from your computer and connect it to the USB port of the Edge 300,

located on the side of the device.

2. SSH into the device using either PuTTy (on a Windows PC) or Terminal (on a Mac) using the

commands shown below. Replace {device IP} with the actual IP address of the Edge device. (verify

with your network administrator regarding the correct IP address and root credentials for the Edge

300).

3. Use the blkid command to locate the USB drive. (usually /dev/sdxx with xx being b1, b2 or c1, c2

etc.) For this guide, we will assume it is /dev/sdb1.

4. Mount the USB drive.

5. Unmount the USB drive. Copy the firmware image onto the Edge 300 device (into the /apps/

directory). Wait for the task to finish. The copying of the image file will be completed when the

console displays a # symbol at the beginning of the command line.

6. Without ejecting your USB drive, run the following commands (remember to replace sdb1 with your

blkid if discovered to be different from Step 3). Note that each command will take some time to

execute. Wait until each command has completed (console displays a #) before proceeding to the

next command. When all commands have been executed, remove the USB drive from the device.

#sshroot@{deviceIP}

#root@{deviceIP}password:cisco

#blkid

/dev/sdb1:LABEL="USBDRIVE"UUID="7288-0792"TYPE="vfat"

#mount/dev/sdb1/tmp/mnt

#cp/tmp/mnt/smi-usb-sunbird-1.5.0-delivery.tar.gz/apps/

#umount/tmp/mnt

FlashingtheFirmware

1. Press and hold the power button on the Edge 300 to turn it OFF. Connect the newly created

bootable USB drive into the USB port again, located on the side of the device.

2. Press and hold the power button on the Edge 300 to turn it back ON. Using your paper clip / SIM

eject tool, press and hold the reset button located next to the power button of the device for about 5

seconds until the device reboots itself.

#mkfs.ext3/dev/sdb1

#mount/dev/sdb1/tmp/mnt

#tarxvzf/apps/smi-usb-sunbird-1.5.0-delivery.tar.gz–C/tmp/mnt/

#umount/tmp/mnt

3. Once rebooted, the Edge 300 device will read the contents of the USB drive and begin flashing the

firmware. The power LED will be flashing continuously at this point, indicating the firmware update is

in process. The firmware flashing will be completed when you are able to view the login screen on a

connected display.

© 2018 Appspace Inc. All Rights Reserved | Legal | Give Feedback

Autres manuels pour Edge 300 Series

1

Table des matières

Autres manuels Cisco Matériel réseau

Cisco

Cisco WAE-674-K9 - Wide Area Application Engine... Manuel

Cisco

Cisco 2431 - IAD Router Manuel utilisateur

Cisco

Cisco UCS X10c Instructions d'installation et d'entretien

Cisco

Cisco Octal-Port DMT ATU-C Line Card Manuel technique

Cisco

Cisco Cisco 5400 ENCS Manuel

Cisco

Cisco GS7000 Manuel utilisateur

Cisco

Cisco Firepower 1010 Manuel utilisateur

Cisco

Cisco ONS 15454 Manuel utilisateur

Cisco

Cisco Catalyst 8510 Manuel utilisateur

Cisco

Cisco ASR 5500 Mode d’emploi

Cisco

Cisco ONS 15310-CL Manuel utilisateur

Cisco

Cisco Nexus 3000 series Manuel utilisateur

Cisco

Cisco N540X-6Z18G-SYS-A Manuel utilisateur

Cisco

Cisco Network Adapter VIP-FE-TX/4E Manuel de l'opérateur

Cisco

Cisco Wide Area Application Engine 612 Manuel

Cisco

Cisco Catalyst 8300 Series Manuel

Cisco

Cisco Firepower 1100 Series Manuel

Cisco

Cisco ASR 9000 Series Manuel utilisateur

Cisco

Cisco ASA 5506-X Manuel

Cisco

Cisco CATALYST RPS 2300 Guide de démarrage rapide

Cisco

Cisco ONS 15540 ESP Manuel

Cisco

Cisco Meraki Catalyst 9300/X/L-M Series Manuel utilisateur

Cisco

Cisco Meraki MX65W Manuel utilisateur

Cisco

Cisco BR1400 Series Guide de référence rapide

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur