Cisco SCE8000 GBE Manuel utilisateur

QUICK START GUIDE

Cisco SCE8000 10 GBE QUICK START GUIDE

1Preparing for Installation

2Rack-Mounting the SCE8000 Chassis

3Connecting Power Supply Units

4Connecting Management Interfaces and Performing Initial System Configuration

5Cabling Line Ports

6Completing the Installation

7Troubleshooting

8Obtaining Documentation and Submitting a Service Request

Revised: December, 2008, Release 3.1.7, OL-16595-02

1 Preparing for Installation

This section contains warnings, tools and part information, and site preparation details.

Warning

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any

equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for

preventing accidents.

Warning

Only trained and qualified personnel should install, replace, or service this equipment.

Warning

Read the installation instructions before you connect the system to its power source.

Warning

This unit is intended for installation in restricted access areas. A restricted access area is where access can only

be gained by service personnel through the use of a special tool, lock and key, or other means of security, and is

controlled by the authority responsible for the location.

Warning

Voltage is present on the backplane when the system is operating. To reduce risk of an electric shock, keep hands

and fingers out of the power supply bays and backplane areas.

Warning

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Warning

Before you begin the installation of the SCE8000, read the Regulatory Compliance and Safety Information for the

Cisco SCE8000 Platform document.

Site Preparation

•Verify that the power service at the site is suitable for the SCE8000 chassis.

•Print out and have accessible the Site Planning Checklist and the Cisco SCE8000 Installation Checklist from the Cisco

SCE8000 Installation and Configuration Guide to record information about this installation.

Tools and Parts

Use the following list of tools and parts as a checklist for preparing to install the SCE 8000 chassis:

•Number 1 and number 2 Phillips screwdrivers

•3/16-inch flat-blade screwdriver

•Tape measure and level

•Masking tape or some other method of marking the desired installation height in the rack

•One grounding lug

•Two M4 (metric) hex-head screws with locking washers

Note The grounding lug and M4 hex-head screws with locking washers are provided in kit 69-0815-01

•One grounding wire—Must be sized according to local and national installation requirements. Depending on the power

supply and system, a 12 AWG conductor or larger size wire is required for U.S. installations.

•Crimping tool—Must be large enough to accommodate the girth of the grounding lug when crimping the grounding cable

into the lug.

•Wire-stripping tool

•Appropriate cables to connect the SCE8000 to the network and console terminal

Unpacking the Cisco SCE8000 Chassis

Tip When you unpack the Cisco SCE8000, do not discard the shipping container. Flatten the shipping cartons and store

them with the pallet. You may need these containers if you move or ship the Cisco SCE8000 in the future.

Check the contents of the shipping container:

•Check the contents of the accessories kit against the list of accessories in the Cisco SCE8000 Component List in the Cisco

SCE8000 Installation and Configuration Guide and the packing slip. Verify that you received all listed equipment, which

should include the following:

–

Hardware and software documentation, if ordered

–

Optional equipment that you ordered, such as network interface cables, transceivers, or special connectors

Check the modules in each slot. Ensure that the configuration matches the packing list and that all the specified interfaces are

included.

2 Rack-Mounting the SCE8000 Chassis

This chapter provides information for rack-mounting the SCE 8000 chassis.

Warning

Before you install, operate, or service the system, read the Regulatory Compliance and Safety Information for the

Cisco SCE8000 Platform. This guide contains important safety information you should know before working with

the system.

Note Before you start the installation described in this chapter, see the Site Planning Checklist in the Cisco SCE8000

Installation and Configuration Guide to verify that all site planning activities are complete.

Installation Guidelines

Table 1 lists rack dimensions. Carefully check the contents of the shipping container, the accessories kit, and optional

equipment.

Table 1 Rack Dimensions

Width 17.75 inches (45.09 cm)

Depth •Minimum: 19.25 inches (48.9 cm)

•Maximum 32 inches (81.3 cm)

Minimum vertical clearance 8.7 inches (22.09 cm) (5 RU)

Caution If the rack is on wheels, ensure that the brakes are engaged or that the rack is otherwise stabilized.

Note We recommend that you maintain a minimum air space of 6 inches (15 cm) between walls and the chassis air vents and

a minimum horizontal separation of 12 inches (30.5 cm) between two chassis to prevent overheating.

The installation hardware is not suitable for use with racks with obstructions (such as a power strip) that could impair access

to field-replaceable units (FRUs).

Warning

To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure

that the system remains stable. The following guidelines are provided to ensure your safety:

>If it is the only unit in the rack, this unit must be mounted at the bottom of the rack.

>When mounting this unit in a partially-filled rack, load the rack from the bottom to the top with the heaviest

component at the bottom of the rack.

>If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the

rack.

The chassis is shipped with the mounting brackets installed on the front of the chassis. You can remove these brackets and install

them on the rear of the chassis, using the holes provided in the rear side of the chassis (Figure 1).

Figure 1 Cisco SCE 8000 Chassis Brackets

Step 1 Position the chassis in the rack as follows. If the:

•Front of the chassis (front panel) is at the front of the rack, insert the rear of the chassis between the mounting posts.

•Rear of the chassis is at the front of the rack, insert the front of the chassis between the mounting posts.

Step 2 Align the mounting holes in the bracket (and optional cable guide) with the mounting holes in the equipment rack.

Step 3 Use a tape measure and level to choose and mark the position that the chassis is to be installed in the rack. Make a mark

at equal height on both sides of the rack. This helps ensure that the chassis is installed straight and level (Figure 2).

FAN STATUS

SCM

SIP

SCE8000-FAN

SYSTEMPOWER

OPTICALBYPASS

STATUS

AUX PORT2

LINK

ACTIVE

MASTER

SCE8000 EXTENDED SERVICECONTROLMODULE

OPTICAL

BYPASS

OPTICAL

BYPASS

CONSOLE

10100

1000

LINK

ACTIVE

PORT1

STATUS

CTRL

OPB-SCE8K-MM

OPTICALBYPASS1

STATUS

CTRL

OPB-SCE8K-MM

OPTICAL BYPASS2

SYSTEMPOWER

OPTICALBYPASS

STATUS

AUXPORT2

10100

1000

LINK

ACTIVE

MASTER

SCE8000 EXTENDED SERVICECONTROLMODULE

SCE8000-SCM-E

SCE8000-SIP

CONSOLE

10100

1000

LINK

ACTIVE

PORT1

OPTICAL

BYPASS

OPTICAL

BYPASS

STATUS

ACTIVE/LINK

SPA-1X10GE-L-V2

STATUS

ACTIVE/LINK

SPA-1X10GE-L-V2

STATUS

ACTIVE/LINK

SPA-1X10GE-L-V2

STATUS

ACTIVE/LINK

SPA-1X10GE-L-V2

10100

1000

270890

Figure 2 Installing the Cisco SCE8000 Chassis in the Rack

Step 4 Install the eight (four per side) 12-24 x 3/4-inch or 10-32 x 3/4-inch screws through the holes in the bracket and into

the threaded holes in the equipment rack posts.

Step 5 Use a tape measure and level to verify that the chassis is installed straight and level.

Installing an Optical Bypass Module

Two installation options exist for external bypass modules:

•Chassis mount panel—This panel is mounted on slot #4 of the SCE 8000 chassis. It hosts two optical bypass modules, which

will serve the two traffic links supported by one Cisco SCE 8000 chassis.

•External mounting panel—This panel can be mounted in any 19-inch rack. It hosts up to 4 optical bypass modules, which

serve four traffic links supported by two Cisco SCE 8000 platforms.

Step 1 For external mounting, install the external mounting panel in the 19-inch rack. Screw the mounting panel to the rack

using four 3/4-inch screws, two on each side, through the holes in the mounting panel and into the threaded holes in

the rack posts. For internal mounting, the SCE8000 chassis is shipped with the chassis mounting panel installed in

slot 4.

Step 2 Remove the module filler plate covering the subslot in the mounting panel by loosening the two screws.

Step 3 Carefully insert the optical bypass module into the subslot (no guide rails exist) and tighten the captive screws on either

side of the module (Figure 3).

270891

FAN STATUS

SCM

SIP

SCE8000-FAN

SYSTEMPOWER

OPTICALBYPASS

STATUS

AUX PORT 2

LINK

ACTIVE

MASTER

SCE8000EXTENDEDSERVICECONTROLMODULE

OPTICAL

BYPASS

OPTICAL

BYPASS

CONSOLE

10100

1000

LINK

ACTIVE

PORT 1

A C

A B

C D

B D

STATUS

CTRL

OPB-SCE8K-MM

OPTICAL BYPASS1

STATUS

CTRL

OPB-SCE8K-MM

OPTICAL BYPASS2

SYSTEMPOWER

OPTICALBYPASS

STATUS

AUXPORT2

10100

1000

LINK

ACTIVE

MASTER

SCE8000EXTENDEDSERVICECONTROLMODULE

SCE8000-SCM-E

SCE8000-SIP

CONSOLE

10100

1000

LINK

ACTIVE

PORT 1

OPTICAL

BYPASS

OPTICAL

BYPASS

STATUS

ACTIVE/LINK

SPA-1X10GE-L-V2

STATUS

ACTIVE/LINK

SPA-1X10GE-L-V2

STATUS

ACTIVE/LINK

SPA-1X10GE-L-V2

STATUS

ACTIVE/LINK

SPA-1X10GE-L-V2

10100

1000

Figure 3 Optical Bypass Modules in External Mounting Panel

3 Connecting Power Supply Units

The SCE8000 chassis is shipped with the power supplies (AC or DC) already installed. This section provides information for

grounding the SCE8000 platform and connecting the AC or DC power supply units.

Connecting the Chassis Ground

Note If this equipment is installed in a U.S. or European Central Office, you must connect the system ground on both AC

and DC-powered systems to an earth ground.

Note For DC-powered systems, the system ground is also the power supply ground. The DC ground must be installed with

a permanent connection to an earth ground according to NEC guidelines.

Note When you use the PWR-2700-DC/4 power supply in the Cisco SCE8000 chassis, additional grounding requirements

exist.

Two threaded M4 holes are provided on the chassis frame to attach the ground cable.

270994

FANSTATUS

SCM

SIP

SCE8000-FAN

SYSTEMPOWER

OPTICAL BYPASS

STATUS

AUX PORT2

LINK

ACTIVE

MASTER

SCE8000EXTENDEDSERVICECONTROLMODULE

OPTICAL

BYPASS

OPTICAL

BYPASS

CONSOLE

10100

1000

LINK

ACTIVE

PORT 1

SYSTEMPOWER

OPTICALBYP

ASS

STATUS

AUXPORT2

10 100

1000

LINK

ACTIVE

MASTER

SCE8000EXTENDEDSERVICECONTROLMODULE

SCE8000-SCM-E

SCE8000-SIP

CONSOLE

10100

1000

LINK

ACTIVE

PORT 1

OPTICAL

BYPASS

OPTICAL

BYPASS

STATUS

ACTIVE/LINK

SPA-1X10GE-L-V2

STATUS

ACTIVE/LINK

SPA-1X10GE-L-V2

STATUS

ACTIVE/LINK

SPA-1X10GE-L-V2

STATUS

ACTIVE/LINK

SPA-1X10GE-L-V2

10100

1000

Before you connect system power or turn on the Cisco SCE 8000 chassis, you must complete this procedure:

Step 1 Remove approximately 0.75 inch (19 mm) of the covering from the end of the grounding wire using a wire-stripping

tool.

Step 2 Insert the stripped end of the grounding wire into the open end of the grounding lug.

Step 3 To secure the grounding wire in place in the grounding lug, use the manufacturer recommended crimping tool.

Step 4 Locate and remove the adhesive label from the system grounding pad on the chassis (Figure 4).

Figure 4 Installing the System Ground

Step 5 Place the grounding wire lug against the grounding pad, making sure that solid metal-to-metal contact exists.

Step 6 Secure the grounding lug to the chassis using two M4 screws. Ensure that the grounding lug does not interfere with

other hardware or rack equipment.

Step 7 To ensure adequate earth ground for the Cisco SCE8000 chassis, prepare the other end of the grounding wire, and

connect it to an appropriate grounding point at your site.

Connecting Power

The following sections describe how to reconnect the AC or DC power.

Installing a DC-Input Power Supply

Note The DC return must remain isolated from the system frame and chassis (DC-I).

Warning

Before you perform any of the following procedures, ensure that power is removed from the DC circuit.

FAN STATUS

SCM

SIP

SCE8000-FAN

SYSTEM POWER

OPTICAL BYP

ASS

STATUS

AUXPORT2

LINK

ACTIVE

MASTER

SCE8000EXTENDEDSERVICECONTROL MODULE

OPTICAL

BYPASS

OPTICAL

BYPASS

CONSOLE

10100

1000

LINK

ACTIVE

PORT1

C D

B D

STATUS

CTRL

OPB-SCE8K-MM

OPTICAL BYPASS1

STATUS

CTRL

OPB-SCE8K-MM

OPTICAL BYPASS2

SYSTEM POWER

OPTICAL BYP

ASS

STATUS

AUX PORT2

10100

1000

LINK

ACTIVE

MASTER

SCE8000EXTENDEDSERVICECONTROL MODULE

SCE8000-SCM-E

SCE8000-SIP

CONSOLE

10100

1000

LINK

ACTIVE

PORT 1

OPTICAL

BYPASS

OPTICAL

BYPASS

STATUS

ACTIVE/LINK

SPA-1X10GE-L-V2

STATUS

ACTIVE/LINK

SPA-1X10GE-L-V2

STATUS

ACTIVE/LINK

SPA-1X10GE-L-V2

STATUS

ACTIVE/LINK

SPA-1X10GE-L-V2

10100

1000

270892

System ground

connector

System ground

connector

Grounding

lug

Wire

Note Because the power requirement of the SCE8000 will not exceed 1350 W, it is not necessary to connect two pairs of input

wires to each power supply. If you want to connect two pairs of input wires, both pairs of input wires for one 2700 W

DC-input power supply must come from the same battery system (A feed); and both pairs of input wires for the other

power supply must come from another battery system (B feed).

Note For multiple DC input power supplies, each DC input must be protected by a dedicated circuit breaker or fuse. The

circuit breaker or fuse should be sized according to the power supply input rating and local or national electrical code

requirements.

Step 1 Power supply ground is required. Install the PWR-2700-DC/4 power supply ground as described in this procedure.

Note The system ground connection with the PWR-2700-DC/4 power supply in a Cisco SCE 8000 is provided by the

PWR-2700-DC/4 power supply ground. Additionally, you can connect a system (earth) ground.

Note You must always connect the PWR-2700-DC/4 power supply ground.

Note You must always connect the PWR-2700-DC/4 power supply ground for both power supplies.

Note If you intend to use an additional system (earth ground), ensure that the system ground connection is made. For

ground connection installation instructions, see the “Connecting the Chassis Ground” section on page 6.

Step 2 Remove the plastic bag attached to the front panel and put aside. This bag contains two plastic terminal block barriers,

two cable ties, and two cable holder covers.

Step 3 Verify that power is off to the DC circuit connected to the power supply you are installing. Grasp both power supply

handles (Figure 5.) Slide the power supply into the power supply bay. Make sure that the power supply is fully seated

in the bay.

Figure 5 Handling a DC-Input Power Supply

Step 4 Tighten the power supply captive installation screws.

Warning

To ensure protective grounding continuity, power supply captive installation screws must be tight.

Note Because the power requirement of the SCE 8000 does not exceed 1350 W, it is not necessary to connect two pairs

of input wires to each power supply. If you want to connect two pairs of input wires, both pairs of input wires for

one 2700 W DC-input power supply must come from the same battery system (A feed); and both pairs of input

wires for the other power supply must come from another battery system (B feed).

Note For multiple DC input power supplies, each DC input must be protected by a dedicated circuit breaker or fuse. The

circuit breaker or fuse should be sized according to the power supply input rating and local or national electrical

code requirements.

Step 5 Remove the four screws securing the terminal block cover, and slide the cover off of the terminal block (Figure 6).

Figure 6 DC-Input Front Panel for 2700 W DC-Input Power Supply

Step 6 Attach the appropriate lugs to the DC-input wires and ground wire. The wires should be sized according to local and

national installation requirements. Use only copper wire. The maximum width of a lug is 0.600 inch (15.2 mm).

Note For North American installations, use fine-stranded copper conductors rated for 90-degrees Celsius.

1Captive installation screw 7Cable holder cover

2DC power cable terminal block 8Cable holder

3Status LEDs 9Tie-wrap

4DC power cable terminal block cover 10 Cable holder

5Cable holder cover 11 Tie-wrap

6Ground

132219

PWR-2700-DC/4

-VE-1

-VE-2

INPUT1

48V-60V

=40A

INPUT2

48V-60V

=40A

FAN

OUTPUT

FAIL

ALL FASTENERS MUST BE FULLY ENGAGED

PRIOR TO OPERATING THE POWER SUPPLY

Note The power supply terminal block lug opening width is 0.62 inch (15.8 mm). The terminal posts are centered

0.625 inches (15.88 mm) apart and are 1/4-20 threaded. We recommend that you use an appropriately sized

industry standard 2-hole, standard barrel compression lug. The power supply ground studs, located below the

terminal block, are also threaded 1/4-20 and require two 1/4-inch split-ring washers and two 1/4-20 hex nuts.

Step 7 Connect the DC-input wires to the 2700 W power supply terminal block. Depending onto which side you are

connecting the DC-input wires, be sure that the DC-input wires rest in the appropriate cable holder. Figure 7 shows

DC-input wires coming in from the left side.

Connect the DC-input wires to the 2700 W power supply terminal block in this order (Figure 7):

•Ground

•Negative (-)

•Positive (+)

Note When you tighten the terminal nuts, make sure they are snug. Do not overtighten them. Recommended torque

strength is 20 inch-pounds. Over-tightening the terminal nuts can break the terminal block (maximum torque:

36 inch-pounds).

Figure 7 DC-Input Wires on Left Side

When you install the unit, the ground connection must always be made first and disconnected last.

Step 8 Secure the ground cable to the cable holder using the two cable-ties.

Step 9 Retrieve the cable holder covers from the plastic bag and attach to the front panel at the locations (see Figure 6).

Note If the cable holder illustrated as number 5 and 8 in Figure 6 does not hold the DC input cables snugly, use a long

cable tie to secure the cable holders as illustrated in number 9.

Step 10 Secure the terminal block cover using four screws and the terminal block barriers with two screws each.

Step 11 Turn on the DC inputs and verify power supply operation by checking the power supply front panel LEDs.

The power supply rear panel LEDs should be in the following states:

•Input OK LED is green

•Fan OK LED is green

•Output Fail LED is not lit

If the LEDs indicate a power problem, see the “Troubleshooting” section on page 21.

132220

INPUT1

48V-60V

=40A

INPUT2

48V-60V

=40A

FAN

OUTPUT

FAIL

ALL FASTENERS MUST BE FULLY ENGAGED

PRIOR TO OPERATING THE POWER SUPPLY

PWR-2700-DC/4

Autres manuels pour SCE8000 GBE

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Cisco Matériel réseau

Cisco

Cisco IPS 7.1 Manuel utilisateur

Cisco

Cisco ASR 9000 Series Manuel utilisateur

Cisco

Cisco IP/VC 3500 Instructions originales

Cisco

Cisco GRP= Guide rapide

Cisco

Cisco TELEPRESENCE MCU ACCESSING CONFERENCES - Manuel utilisateur

Cisco

Cisco Firepower 9300 Manuel

Cisco

Cisco VSVM Mode d’emploi

Cisco

Cisco Network Adapter VIP-FE-TX/4E Manuel de l'opérateur

Cisco

Cisco o UCS X440p Instructions d'installation et d'entretien

Cisco

Cisco NCS 1001 Mode d’emploi

Cisco

Cisco Catalyst 8510 Manuel utilisateur

Cisco

Cisco Linksys WES610N Manuel utilisateur

Cisco

Cisco NM-1A-T3 - 1port Ds3 Atm Network Module Manuel utilisateur

Cisco

Cisco IDS 4210 - Intrusion Detection Sys 4210... Manuel utilisateur

Cisco

Cisco NCS 2002 Mode d’emploi

Cisco

Cisco ONS 15454 Feuille d'instructions

Cisco

Cisco CVPN3002-K9 - Fast Ethernet VPN Gateway Manuel utilisateur

Cisco

Cisco Performance Routing Engine 5 Manuel

Cisco

Cisco C8510MSR-SKIT-DC - Catalyst 8510 Multiservice Switch... Manuel utilisateur

Cisco

Cisco ISA550 Mode d’emploi

Cisco

Cisco NCS 1004 Manuel d'installation

Cisco

Cisco SPA901-UK - Small Business Pro Manuel utilisateur

Cisco

Cisco NSS2000 Series Manuel utilisateur

Cisco

Cisco CiscoWorks Wireless LAN Solution Engine Manuel de l'opérateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur