Cisco NCS 2000 series Manuel utilisateur

Installing the Cisco NCS 2000 Series Passive

Optical Modules

Last Modified: 2019-02-22

Installing the Cisco NCS 2000 Series Passive Optical Modules

Introduction

This document explains how to install and operate the Cisco NCS 2000 Series passive optical modules, the

fiber shuffle, and the MPO fan-out unit. The Cisco NCS 2000 Series encompasses platforms from Cisco NCS

2002 onwards.

The passive optical modules are used to build the optical network system. The fiber shuffle and MPO fan-out

unit mechanically holds 14 and 10 passive optical modules respectively, thus enabling interconnection of flex

spectrum ROADM nodes that contain 16-WXC or SMR-FS cards.

The passive optical modules, fiber shuffle, and MPO fan-out unit can be installed on:

• 19-inch (482.6 mm) or 23-inch (584.2 mm) EIA standard racks

• 19-inch (482.6 mm) IEC rack

• 600 mm x 600 mm or 600 mm x 300 mm ETSI rack

The following table lists the PIDs of the fiber shuffle and MPO fan-out unit:

Table 1: PIDs of the Fiber Shuffle and MPO Fan-out Unit

DescriptionModule

The MF-6RU unit is referred to as the fiber shuffle.

A combination of 14 single-slot NCS2K-MF-DEG-5

(NCS2K-MF-DEG-5-CV) and NCS2K-MF-UPG-4

(NCS2K-MF-UPG-4-CV) passive optical modules

can be installed in this unit. It is also possible to install

a combination of 14 single-slot

NCS2K-MF-2MPO-ADP, NCS2K-MF-4x4-COFS,

NCS2K-MF-MPO-8LC, and NCS2K-MF-6AD-CFS

passive optical modules.

NCS2K-MF-6RU= (MF-6RU)

Installing the Cisco NCS 2000 Series Passive Optical Modules

DescriptionModule

The MF10-6RU unit is referred to as the MPO fan-out

unit.

A combination of 10 double-slot

NCS2K-MF-10AD-CFS, NCS2K-MF-16AD-CFS,

NCS2K-MF-16AE-CFS, NCS2K-MF-MPO-16LC

(NCS2K-MF-M16LC-CV), NCS2K-MF-MPO-20LC,

and NCS2K-MF-8X10G-FO units can be installed in

this unit.

NCS2K-MF10-6RU= (MF10-6RU)

Blank unit for the MF-6RU unit.NCS2K-MF-1SL-CVR=

Blank unit for the MF-10-6RU unit.NCS2K-MF-2SL-CVR=

USB cable; two meters longNCS2K-USB3-CBL-2=

USB cable; three meters longNCS2K-USB3-CBL-3=

Plastic transparent cover for the MF-6RU and

MF-10-6RU unit.

NCS2K-MF-6RU-CVR=

All passive optical modules, (except the mesh patch panel module), are installed using the rack mounting

bracket that is one rack unit (RU) high and can be directly connected to the NCS 2015 ECU. The passive

optical modules can also be installed in the fiber shuffle or MPO fan-out unit.

The following table lists the passive optical modules:

DescriptionModule

16-channel colorless omni-directional add/dropNCS2K-MF-16AD-CFS=

4-channel colorless omni-directional add/dropNCS2K-MF-4X4-COFS=

MPO to 8-LC adapterNCS2K-MF-MPO-8LC=

5-degree mesh moduleNCS2K-MF-DEG-5=

4-degree upgrade moduleNCS2K-MF-UPG-4=

MPO-16 to 16-LC fan-out moduleNCS2K-MF-MPO-16LC=

Double MPO-16 to two MPO-8 adapter moduleNCS2K-MF-2MPO-ADP=

16-port add/drop module with express capabilityNCS2K-MF-16AE-CFS=

10-port add/drop moduleNCS2K-MF-10AD-CFS=

8-degree mesh patch panel with 5 add/drop portsNCS2K-PPMESH8-5AD=

5-degree mesh connection verification module with

MPO-8 loopback caps (NCS2K-MPO-LBK=)

NCS2K-MF-DEG-5-CV=

4-degree upgrade connection verification module with

MPO-8 loopback caps (NCS2K-MPO-LBK=)

NCS2K-MF-UPG-4-CV=

Installing the Cisco NCS 2000 Series Passive Optical Modules

Introduction

DescriptionModule

MPO-16 to 16-LC fan-out connection verification

module with LC loopback caps (NCS2K-LC-LBK=)

NCS2K-MF-M16LC-CV=

MPO-24 to 20-LC fan-out moduleNCS2K-MF-MPO-20LC

Splitter/coupler module with six ports used as

colorless or gridless add/drop units in NCS2K

ROADM configurations.

NCS2K-MF-6AD-CFS=

MPO to LC fan-out module used as client

interconnection for the NCS2K and NCS4K line cards

using QSFP+ ports.

NCS2K-MF-8X10G-FO=

• All modules can be used to accommodate the ROADM nodes built with the SMR-FS and AD-FS cards.

• A set of photodiodes are included on selected ports of each module for optical power monitoring.

•USB communication channel can be used to retrieve the optical power levels monitored by the photodiodes

and the inventory and insertion loss (IL) data of the optical paths stored in the modules. The USB channel

can also be used to activate electrical actuators or LEDs present on the front panel of the module.

• The xx SMR9 FS, SMR20 FS, or SMR20 FS CV and the 12-AD-FS or 16-AD-FS cards can be

interconnected by the NCS2K-MF-UPG-4=, NCS2K-MF-UPG-4-CV=, NCS2K-MF-DEG-5=,

NCS2K-MF-DEG-5-CV=, NCS2K-MF-MPO-16LC=, NCS2K-MF-M16LC-CV=,

NCS2K-MF-2MPO-ADP=, or the NCS2K-PPMESH8-5AD= module.

• The NCS2K-MF-16AE-CFS= and the NCS2K-MF-10AD-CFS= modules are only used as a passive

add/drop modules in the Not-DWDM networks.

The following table lists the MPO cables that can be used with the passive modules from Release 10.6.1:

DescriptionMPO Cables

Fan-out cable with one MPO-24 connector on one

side and 16 LC connectors on the other side.

The cable is two meters long and can be used in

ROADM configurations with the

NCS2K-MF-6AD-CFS module. This cable can also

be used as a fan-out cable to connect the LC interface

directly to the SMR20 FS MPO ports.

ONS-MPO-16LC-2

Multi-fiber patch cord with MPO-12 connectors. The

12 fibers have straight connections. There are four

variants: two, four, six, and eight meters.

• ONS-12MPO-MPO-2=

• ONS-12MPO-MPO-4=

• ONS-12MPO-MPO-6=

• ONS-12MPO-MPO-8=

The cables can interconnect the QSFP+ client ports

of NCS2K-400G-2C2 and NCS4K-4H-OPW-QC2

with the NCS2K-MF-8X10G-FO passive module.

ONS-12MPO-MPO-x

Installing the Cisco NCS 2000 Series Passive Optical Modules

Introduction

DescriptionMPO Cables

Multi-fiber patch cord with MPO-12 connectors. The

12 fibers have crossed fiber interconnections. There

are four variants: two, four, six, and eight meters.

• ONS-12MPO-XMPO-2=

• ONS-12MPO-XMPO-4=

• ONS-12MPO-XMPO-6=

• ONS-12MPO-XMPO-8=

The cable is used to interconnect the

NCS2K-MF-DEG-5-CV and the

NCS2K-MF-UPG-4-CV passive modules with the

NCS2K-MF-MPO-8LC adapter.

ONS-12MPO-XMPO-x

Multi-fiber patch cord with MPO-24 connectors that

has only 16 fibers connected. Fibers 1, 2, 11, 12, 13,

14, 23, and 24 are not connected. There are four

variants: two, four, six, and eight meters.

• ONS-16MPO-MPO-2=

• ONS-16MPO-MPO-4=

• ONS-16MPO-MPO-6=

• ONS-16MPO-MPO-8=

The cable is used for interconnections inside the

ROADM with MPO-24 standard. The patch cord can

be used for interconnections between SMR20 FS and

NCS2K-MF-M16LC-CV, or NCS2K-MF-2MPO-ADP

or NCS2K-PPMESH8-5AD. The patch cord can also

be used for interconnections between

NCS2K-16-AD-CCOFS and

NCS2K-MF-M16LC-CV.

ONS-16MPO-MPO-x

Safety Information

Before you install, operate, or service the passive optical modules, you must read the Regulatory Compliance

and Safety Information for Cisco NCS 2000 Series document for important safety information and warning

translations.

The passive optical modules are compliant with the GR 1089, UL60950 /CSA 22.2 No. 60950-00, and IEC

60950 standards.

Laser Radiation Emission Restrictions

The Class 1M Laser safety and warning label affixed to the passive optical modules indicate that the product

should never be used or installed in an optical network with emissions higher than Class 1M.

Class 1M laser radiation when open. Do not view directly with optical instruments. Statement 281

Warning

Installing the Cisco NCS 2000 Series Passive Optical Modules

Safety Information

Laser Safety During Operation

Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or

view directly with optical instruments. Statement 1051

Warning

Electrical Safety

The passive optical modules are optically and electrically passive and require no electrical connections. No

electrostatic discharge (ESD) or other electrical safety considerations apply.

Fiber Shuffle

The MF-6RU unit is six RU high and can be used to interface 14 single slot passive optical modules with the

NCS 2015 ECU. It contains a USB 3.0 hub that consolidates all USB 2.0 connections between the passive

optical modules units and the NCS 2015 ECU using a single USB cable. It allows connections between line

cards and optical passive modules units using simple cabling. The slots are covered by blank units. The

MF-6RU unit is shipped with USB connectors connected to the corresponding blank units. A plastic transparent

door can be installed in front of the unit for fiber and cable management. Mounting brackets are shipped with

the unit.

Figure 1: NCS2K-MF-6RU Unit

Cable guide2Blank unit1

USB connector3

Installing the Cisco NCS 2000 Series Passive Optical Modules

Laser Safety During Operation

MPO Fan-out Unit

The MF10-6RU unit is six RU high and can be used to interface 10 double slot passive optical modules with

the NCS 2015 ECU. It contains a USB 3.0 hub that consolidates all USB 2.0 connections between the passive

optical modules units and the NCS 2015 ECU using a single USB cable. It allows connections between line

cards and optical passive modules units using simple cabling. It also has an additional USB 3.0 port on its

faceplate that allows it to be connected to only one MF10-6RU unit.

The slots are covered by blank units and USB connectors are connected to the corresponding blank units. A

plastic transparent door can be installed in front of the unit for fiber and cable management. Mounting brackets

are shipped with the unit.

Figure 2: NCS2K-MF10-6RU Unit

Cable guide2Blank unit1

USB connector3

This procedure describes the steps to install the MF-6RU or MF10-6RU unit on the ANSI or ETSI equipment

rack.

Procedure

Step 1 For a 23-inch ANSI or 21-inch ETSI rack installation, mount the four brackets on the MF-6RU unit or

MF10-6RU unit and:

a) Place the mounting bracket flush against the MF-6RU or MF-0-6RU unit.

b) Align the mounting bracket screw holes against the MF-6RU or MF10-6RU unit screw holes.

c) Insert the M6 screws and tighten them.

d) Repeat steps 1a through 1c to mount the remaining three brackets on the unit.

Installing the Cisco NCS 2000 Series Passive Optical Modules

MPO Fan-out Unit

Figure 3: Mounting Brackets on the MF-6RU Unit for a 23-inch ANSI Rack Installation

Washer223-inch ANSI rack

mounting bracket

Screw3

Installing the Cisco NCS 2000 Series Passive Optical Modules

MPO Fan-out Unit

Figure 4: Mounting Brackets on the MF-6RU Unit for a 21-inch ETSI Rack Installation

Washer2Z shaped 21-inch ETSI

rack mounting bracket

Screw3

Installing the Cisco NCS 2000 Series Passive Optical Modules

MPO Fan-out Unit

Figure 5: Mounting Brackets on the MF10-6RU Unit for a 23-inch ANSI Rack Installation

Washer223-inch ANSI rack

mounting bracket

Screw3

Installing the Cisco NCS 2000 Series Passive Optical Modules

MPO Fan-out Unit

Figure 6: Mounting Brackets on the MF10-6RU Unit for a 21-inch ETSI Rack Installation

Washer2Z shaped 21-inch ETSI

rack mounting bracket

Screw3

Step 2 Install the MF-6RU or MF10-6RU unit on the appropriate rack equipment:

a) Lift the MF-6RU or MF10-6RU unit to the desired position in the rack.

b) Align the screw holes on the mounting brackets with the mounting holes in the rack.

For a 19-inch ANSI rack installation, external mounting brackets are not installed on the MF-6RU

or MF10-6RU unit. The unit is mounted directly on the equipment rack using screws and washers.

Note

c) Insert the screws and tighten them.

Installing the Cisco NCS 2000 Series Passive Optical Modules

MPO Fan-out Unit

Autres manuels pour NCS 2000 series

Table des matières

Autres manuels Cisco Matériel réseau

Cisco

Cisco AIR-BR1410A-A-K9 - Aironet 1410 Wireless... Manuel utilisateur

Cisco

Cisco MC3810 Series Manuel utilisateur

Cisco

Cisco IAD2430 Series Manuel

Cisco

Cisco MERAKI MX85 Series Manuel

Cisco

Cisco Cisco 5400 ENCS Manuel

Cisco

Cisco NM-1FE-TX - Interface Module Ethernet Manuel utilisateur

Cisco

Cisco ISA 3000 Guide de démarrage rapide

Cisco

Cisco Fourth-Generation Versatile Interface Processor... Manuel de l'opérateur

Cisco

Cisco IAD1101 Manuel utilisateur

Cisco

Cisco AGS+ Mode d’emploi

Cisco

Cisco 8011-2X2XP4L Manuel

Cisco

Cisco ONS 15310-CL Manuel utilisateur

Cisco

Cisco CSC-C2FCIT Mode d’emploi

Cisco

Cisco NCS 2000 series Manuel utilisateur

Cisco

Cisco NCS 4201 Manuel

Cisco

Cisco NCS 2002 Mode d’emploi

Cisco

Cisco 1230AG - Aironet - Wireless Access Point Manuel utilisateur

Cisco

Cisco NM-1A-T3 - 1port Ds3 Atm Network Module Manuel utilisateur

Cisco

Cisco C7200-I - Input/Output Controller - Control... Manuel utilisateur

Cisco

Cisco WBPN Manuel utilisateur

Cisco

Cisco Meraki MX65W Manuel utilisateur

Cisco

Cisco 40-Gigabit and 100-Gigabit CFP Transceiver... Guide de démarrage rapide

Cisco

Cisco ONS 15454 Feuille d'instructions

Cisco

Cisco Remote PHY Shelf 7200 Manuel d'installation

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur