Cisco 5400 Series Mode d’emploi

Installing the Device

•Unpacking the Device, on page 1

•Locating the Product ID, Serial Number, Version ID and Common Language Equipment Identifies

(CLEI), on page 1

•Installing the Cisco 5400 ENCS, on page 2

•Powering On the Server, on page 5

•Initial Server Setup, on page 6

Unpacking the Device

The device, accessory kit, publications, and any optional units may be shipped in more than one container.

When you unpack the containers, check the packing list to ensure that you have received all the items on the

list.

Only unpack the product when you are ready to install it. This will help prevent accidental damage.

Locating the Product ID, Serial Number, Version ID and Common

Language Equipment Identifies (CLEI)

The serial number (SN), product ID (PID), version ID (VID), and Common Language Equipment Identifier

(CLEI) are printed on a label on the label tray located on the server chassis or motherboard.

Installing the Device

Figure 1: Label Tray

Serial Number2Product ID1

CLEI4PID/VID3

Installing the Cisco 5400 ENCS

If it is not already installed, the DIMMs, M.2 storage module and RAID card must be installed before

rack-mounting or wall-mounting the chassis. We recommend that you install the power supply when you have

the best access to the back panel of the device; this could be before or after you mount the device. You can

install the NIM and HDDs either before or after you mount the chassis.

Rack-Mounting the Chassis

The Cisco 5400 ENCS can be installed in 19-inch (48.26-cm) racks. Use the standard brackets shipped with

the router for mounting the chassis in a 19-inch EIA rack.

You can mount the device in the following ways:

• Front mounting—Brackets attached at the front of the chassis with the front panel facing forward

• Back mounting—Brackets attached at the back of the chassis with the back panel facing forward

• Center-front mounting—Brackets attached in the center front of the chassis with the front panel facing

forward

• Center-back mounting—Brackets attached in the center back of the chassis with the back panel facing

forward

Attaching Brackets to the Chassis

Attach one mounting bracket to each side of the device as shown in Figures 6 and 7. You will need four screws

to attach each bracket to the device; so, you will need eight screws in total to attach both the brackets to the

device. Use the screws provided along with the mounting kit to attach the screws to the device.

Installing the Device

Installing the Cisco 5400 ENCS

Figure 2: Bracket Installation for Front Mounting

Figure 3: Bracket Installation for Back Mounting

Mounting the device in a Rack

After you attach the brackets to the device, install the chassis on the rack as shown in Figure 8. You will need

two screws to attach each bracket to the rack; so, you will need four screws in total to attach the device to the

rack. The screws for attaching the device to the rack are not provided with the kit.

Installing the Device

Rack-Mounting the Chassis

Figure 4: Mounting the Chassis on the Rack - Front and Back

The screw slots in the brackets are spaced to line up with every second pair of screw holes in the rack. When

the correct screw holes are used, the small threaded holes in the brackets line up with unused screw holes in

the rack. If the small holes do not line up with the rack holes, you must raise or lower the brackets to the next

rack hole.

Tip

Wall-Mounting the Chassis

These are the steps to wall mount the chassis:

1. Attach the brackets to the device using the screws and plastic spacers provided with the mounting kit. As

shown in Figure 9, two screws and two plastic spaces should be used to attach each bracket to the chassis.

2. Fix the router to the wall using the brackets that you attached to the device. The screws for attaching the

device to the wall are not provided with the kit. Depending on the type of wall (wood, brick, stone etc),

use appropriate screws to fix the device to the wall.

Route the cables so that they do not put a strain on the connectors or mounting hardware.

Note

Installing the Device

Wall-Mounting the Chassis

Figure 5: Wall Mounting the Server

Powering On the Server

When the power cord is connected to the system, both the management controller (CIMC) and the server is

automatically powered on. When the system is powered on, do not press the front-panel power button. If you

press the front-panel power button, it will power off the server, but the management controller (CIMC)

continues to be operational. You must press this button again to power on the server.

Note

1. Attach the power cord to the power supply unit in the server and then attach the other end of the power

chord to the grounded power outlet.

2. Wait for approximately three minutes.

3. Verify the power status of the system by looking at the system power status LED. The power status LED

blinks in amber color during initial boot up and in solid amber when the system reaches the standby power

mode.

Installing the Device

Powering On the Server

Initial Server Setup

Local Connection Procedure

1. Ensure that the device is powered on.

2. Connect a keyboard and a monitor to the corresponding ports on the front panel of the device.

3. When you see the prompt, you can do the following:

• Press F2 to get into the setup (BIOS) to change some settings.

• Press F8 to configure the IP address of the CIMC.

4. After you have performed the required configuration, save the setup and continue to boot.

Remote Connection Procedure

1. Plug in your terminal server to the Serial CIMC port (Refer to Front panel of Chassis)

2. Telnet into the console and perform the necessary configuration using corresponding commands. You

can also configure the IP address for the Ethernet CIMC port.

Use CIMC to configure the box. For more details, see Initial Setup for UCS C-Series Servers.

Installing the Device

Initial Server Setup

Table des matières

Autres manuels Cisco Matériel réseau

Cisco

Cisco MERAKI MR57 Manuel utilisateur

Cisco

Cisco Linksys NSLU2 Manuel utilisateur

Cisco

Cisco SA-VAM - VPN Acceleration Module Manuel de l'opérateur

Cisco

Cisco PRISMA II XD Manuel utilisateur

Cisco

Cisco Wide Area Virtualization Engine 274 Manuel

Cisco

Cisco ONS 15327 Manuel

Cisco

Cisco ME 1200 Series Manuel

Cisco

Cisco ATM Cable Interface Processor ACIP-SM(=) Manuel de l'opérateur

Cisco

Cisco Prisma EtherLinX Manuel utilisateur

Cisco

Cisco GS7000 Mode d’emploi

Cisco

Cisco ASA Guide de démarrage rapide

Cisco

Cisco IDS-4230-FE - Intrusion Detection Sys Fast Ethernet... Manuel de l'opérateur

Cisco

Cisco ASR 5000 Manuel utilisateur

Cisco

Cisco CVPN3002-K9 - Fast Ethernet VPN Gateway Manuel utilisateur

Cisco

Cisco WAVE-574-K9 - Wide Area Virtualization Engine... Manuel

Cisco

Cisco VSVM Mode d’emploi

Cisco

Cisco GRP= Guide rapide

Cisco

Cisco Firepower 9300 Guide de maintenance et de service

Cisco

Cisco CGR 1240 Manuel utilisateur

Cisco

Cisco NCS 1004 Manuel utilisateur

Cisco

Cisco S170 Web Manuel utilisateur

Cisco

Cisco CMX 3375 Manuel utilisateur

Cisco

Cisco ESR-PRE2 Manuel utilisateur

Cisco

Cisco ONS 15310-MA Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur