Cisco SCE8000 GBE Manuel de l'opérateur

Americas Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

http://www.cisco.com

Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 527-0883

Cisco SCE8000 Installation and

Configuration Guide

Release 3.1.7

November 23, 2010

Text Part Number: OL-16478-03

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL

STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT

WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT

SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE

OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH

ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT

LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF

DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,

WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO

OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at

www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership

relationship between Cisco and any other company. (1005R)

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the

document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

Cisco SCE8000 Installation and Configuration Guide

iii

Cisco SCE8000 Installation and Configuration Guide, Rel 3.1.7

OL-16478-03

CONTENTS

About this Guide ix

Document Revision History ix

Organization x

Related Publications xi

Conventions xi

Obtaining Documentation and Submitting a Service Request xii

CHAPTER

1Cisco Service Control Overview 1-1

Cisco Service Control Solution 1-1

Service Control for Broadband Service Providers 1-2

Cisco Service Control Capabilities 1-2

SCE Platform Description 1-3

Management and Collection 1-4

Network Management 1-5

Subscriber Management 1-5

Service Configuration Management 1-6

Data Collection 1-6

CHAPTER

2Introduction to the Cisco SCE8000 Platform 2-1

Information About the SCE Platform 2-1

Service Control Module (SCE8000-SCM-E) 2-2

Introduction to SIPs and SPAs 2-4

SPA Interface Processors 2-4

Specifying the SIP Subslot Location for a SPA 2-5

Shared Port Adapters 2-5

Modular Optics 2-6

XFP Connections 2-6

The SCE8000-SIP 2-7

The 1-Port 10GBE SPA Interface Module 2-7

The Cisco SCE8000 Optical Bypass 2-8

Optical Bypass Functionality 2-9

Optical Bypass Module Connectivity 2-9

Optical Bypass Module (OPB-SCE8K) 2-10

Contents

Cisco SCE8000 Installation and Configuration Guide, Rel 3.1.7

OL-16478-03

Optical Bypass Module Specifications 2-11

Fan Assembly 2-11

Power Supplies 2-12

Power Supply Cooling 2-13

Load Sharing 2-13

Checking the Shipping Container Contents 2-13

Cisco SCE8000 Component List 2-13

Cisco SCE8000 Installation Checklist 2-14

CHAPTER

3Cisco SCE8000 Topology and Topology-Related Parameters 3-1

The Cisco SCE8000 Platform 3-1

Topology Considerations 3-2

Physical Topologies 3-3

SCE8000 Interface Numbering 3-3

Single Cisco SCE8000 Topologies 3-3

Single Link: Inline Topology 3-4

Dual link: Inline Installation 3-4

Single Link: Receive-only Topology 3-5

Dual Link: Receive-Only Topology 3-5

Dual Cisco SCE8000 Topology (Cascade) 3-6

Multi-Gigabit Service Control Platform (MGSCP) Topology 3-7

Type of SCE Platform Redundancy 3-8

Redundant Cisco 7600 Series Router 3-8

Link Continuity 3-9

Internal Bypass Mechanism 3-9

External Optical Bypass 3-9

Topology-Related Parameters 3-11

Connection Mode Parameter 3-11

Physically Connected Links Parameter 3-12

Priority 3-12

On-Failure Mode Parameter 3-12

Asymmetric Routing Topology 3-13

Asymmetric Routing and Other Service Control Capabilities 3-13

CHAPTER

4Installing the Cisco SCE8000 Chassis 4-1

Preparing for Installation 4-2

Safety 4-2

Site Requirements 4-2

Contents

Cisco SCE8000 Installation and Configuration Guide, Rel 3.1.7

OL-16478-03

Preventing Electrostatic Discharge Damage 4-3

Environmental Requirements 4-3

Power Requirements 4-4

Power Connection Guidelines 4-4

AC-Powered Systems 4-5

DC-Powered Systems 4-11

Site Planning Checklist 4-12

Installing the Cisco SCE8000 Chassis in the Rack 4-13

Unpacking the Cisco SCE8000 Chassis 4-14

Installation Guidelines 4-14

Required Tools 4-15

Installing the Chassis Brackets 4-15

Installing the Chassis in the Rack 4-16

Installing an Optical Bypass Module 4-17

Connecting the System Ground 4-18

Required Tools and Equipment 4-19

Installing the Power Supplies in the Cisco SCE8000 Chassis 4-20

CHAPTER

5Connecting the Management Interfaces 5-1

How to Set Up the Local Console 5-1

Initial Setup Parameters 5-2

Connecting the Management Interface 5-4

How to Cable the Management Port 5-4

How to Verify Management Interface Connectivity 5-5

CHAPTER

6Cabling the Line Ports and Completing the Installation 6-1

Connecting the Line Ports to the Network 6-1

Single Link: Inline Topology 6-2

Single Link: Receive-only Topology 6-2

Dual Link: Single Cisco SCE8000 Topologies 6-2

Dual Link: Two Cisco SCE8000s Topology 6-3

Multi-Gigabit Service Control Platforms (MGSCP) Topologies 6-4

The Optical Bypass Module 6-8

Optical Bypass Module Connectivity 6-9

Cabling the 10GBE Line Interface Ports 6-9

Fiber Specifications 6-10

Optical Device Maintenance 6-10

How to Cable the 10GBE Line Interface Ports 6-10

Contents

Cisco SCE8000 Installation and Configuration Guide, Rel 3.1.7

OL-16478-03

Cabling the 10GBE Line Interface Ports: Using the External Optical Bypass Module 6-11

Testing Connectivity: Examining Link LEDs and Counters 6-13

Examining the LEDs 6-13

How to View the Ten Gigabit Ethernet Port Status 6-13

How to View the Ten Gigabit Ethernet Counters 6-13

How to View the User Log Counters 6-14

How to Load and Activate a Service Control Application 6-14

Cascaded Systems 6-15

How to Install a Cascaded System 6-15

CLI Commands for Cascaded Systems 6-16

Topology-Related Parameters for Redundant Topologies 6-16

How to Configure the Connection Mode 6-17

How to Set the Link Mode 6-17

Monitoring the System 6-18

CHAPTER

7Basic Cisco SCE8000 Platform Operations 7-1

Starting the Cisco SCE8000 Platform 7-1

Checking Conditions Prior to System Startup 7-1

Performing Complex Configurations 7-2

Starting the System and Observing Initial Conditions 7-2

What to Do Next 7-2

Final Tests 7-3

Verifying Operational Status 7-3

Viewing the User Log Counters 7-3

Viewing the Ten Gigabit Ethernet Port Status 7-4

Viewing the Ten Gigabit Ethernet Counters 7-4

Managing Cisco SCE8000 Configurations 7-5

Viewing Configurations 7-5

Saving or Changing the Configuration Settings 7-6

Example for Saving or Changing the Configuration Settings 7-7

Restoring a Previous Configuration 7-8

Example for Restoring a Previous Configuration 7-9

How to Display the SCE Platform Version Information 7-10

Example for Displaying the SCE Platform Version Information 7-10

How to Display the SCE Platform Inventory 7-12

Examples for Displaying the SCE Platform Inventory 7-12

Displaying the SCE Platform Inventory: FRUs Only 7-12

Displaying the Complete SCE Platform Inventory 7-13

How to Display the System Uptime 7-16

Contents

vii

Cisco SCE8000 Installation and Configuration Guide, Rel 3.1.7

OL-16478-03

Example for Displaying the System Uptime 7-16

Rebooting and Shutting Down the SCE Platform 7-16

Rebooting the SCE Platform 7-16

Examples for Rebooting the SCE Platform 7-16

How to Shut Down the SCE Platform 7-17

Examples for Shutting Down the SCE Platform 7-17

CHAPTER

8Troubleshooting 8-1

Troubleshooting Overview 8-1

Information About Troubleshooting Tools 8-2

CLI Commands for Troubleshooting 8-2

Checking the LEDs 8-4

Problem Solving Using a Subsystems Approach 8-6

Identifying Startup Problems 8-6

Troubleshooting the Power Subsystem 8-7

Troubleshooting the Firmware Package Installation 8-8

Troubleshooting the Management Subsystem 8-8

Troubleshooting the Link Interface Subsystem 8-10

Troubleshooting with the User Log 8-11

The Logging System 8-11

How to Copy the User Log to an External Source 8-12

How to Copy the User Log to an Internal Location 8-12

How to View the User Log 8-12

How to Clear the User Log 8-12

How to View the User Log Counters 8-13

How to View the Non-volatile Counter For the User-file-log Only 8-13

Generating a File for Technical Support 8-13

CHAPTER

9Removal and Replacement Procedures 9-1

Safety 9-1

Preventing Electrostatic Discharge Damage 9-2

Supported Hardware 9-3

Removing and Replacing the Power Supply 9-3

Required Tools 9-3

Removing an AC-Input Power Supply 9-3

Installing an AC-Input Power Supply 9-5

Removing a DC-Input Power Supply 9-5

Installing a DC-Input Power Supply 9-7

Removing and Replacing the Fan Assembly 9-11

Contents

viii

Cisco SCE8000 Installation and Configuration Guide, Rel 3.1.7

OL-16478-03

Required Tools 9-11

Removing the Fan Assembly 9-11

Installing the Fan Assembly 9-12

Removing and Replacing Modules 9-13

Required Tools 9-13

Handling SIPs 9-13

Installing a Module 9-14

Removing a Module 9-18

Inserting and Removing a Module: Detail 9-20

Verifying the Installation 9-21

Removing and Replacing Shared Port Adapters 9-23

Required Tools and Equipment 9-23

Laser/LED Safety 9-23

Handling SPAs 9-24

SPA Installation and Removal 9-25

Installing a SPA in a SIP 9-25

Removing a SPA from a SIP 9-26

Removing and Replacing the Optical Bypass Module 9-26

Removing the Optical Bypass Module 9-26

Installing the Optical Bypass Module 9-26

Replacing the Optical Bypass Module without Disrupting Traffic on the Link 9-27

CHAPTER

AUsing Optical Splitters with 10GBE Links A-1

Supported Configurations A-1

Unsupported Configuration A-2

Cisco SCE8000 Installation and Configuration Guide, Rel 3.1.7

OL-16478-03

About this Guide

This preface describes who should read the Cisco SCE8000 Installation and Configuration Guide, how

it is organized, and its document conventions.

This guide is for the networking or computer technician responsible for installing and configuring the

SCE8000 platform on-site. To use this publication, you should be familiar with telecommunications

equipment and installation procedures, as well as electronic circuitry and wiring practices. You should

also have experience as an electronic or electromechanical technician.

This installation guide explains the initial hardware installation and basic configuration procedures for

the SCE8000. It contains procedures for unpacking and installing the device and performing basic

configuration via the setup wizard. After completing the installation and basic configuration procedures

covered in this guide, you will then use the appropriate companion publications to more completely

configure your system.

This guide contains instructions on how to install and run the SCE8000 platform. This guide assumes a

basic familiarity with telecommunications equipment and installation procedures.

Document Revision History

Revision

Cisco Service Control

Release and Date Change Summary

OL-16478-03 3.1.7

November 23, 2010

Added information regarding power consumption in Chapter 4, “Installing the

Cisco SCE8000 Chassis”.

Updated AC Power Specifications in Chapter 4, “Installing the Cisco

SCE8000 Chassis”.

OL-16478-02 3.1.7

December, 2008

Added explanation of casacade topology and cabling.

OL-16478-01 3.1.6S

June, 2008

First version. New document for new product.

Cisco SCE8000 Installation and Configuration Guide, Rel 3.1.7

OL-16478-03

About this Guide

Organization

The major sections of this guide are as follows:

Chapter Title Description

1 Cisco Service Control Overview, page 1-1 This chapter provides a brief introduction to

Cisco Service Control.

2 Introduction to the Cisco SCE8000 Platform,

page 2-1

This chapter provides a hardware overview of

the SCE8000 platform.

3 Cisco SCE8000 Topology and

Topology-Related Parameters, page 3-1

This chapter describes the possible

deployment topologies of the SCE8000 and

explains how various aspects of the topology

determine the configuration of the system.

4 Installing the Cisco SCE8000 Chassis,

page 4-1

This chapter explains how to install a

SCE8000 platform in the rack and properly

ground it.

5 Connecting the Management Interfaces,

page 5-1

This chapter explains how to connect the

SCE8000 platform to a local console and

perform the initial system configuration via

the setup wizard that runs automatically.

6 Cabling the Line Ports and Completing the

Installation, page 6-1

This chapter provides instructions for cabling

the Gigabit Ethernet ports for both one and

two SCE8000 topologies, and for configuring

Gigabit Ethernet (GBE) interface parameters.

In a topology utilizing two SCE8000s

(cascade), this includes the cascade ports as

well as the line ports.

7 Basic Cisco SCE8000 Platform Operations,

page 7-1

This chapter describes how to start up the

SCE8000 platform, reboot, and shutdown. It

also describes how to manage configurations.

8 Troubleshooting, page 8-1 This chapter provides basic system startup

troubleshooting information.

9 Removal and Replacement Procedures,

page 9-1

This chapter explains the procedures for

removing and replacing the power supplies,

fan trays, and other modules.

A Using Optical Splitters with 10GBE Links,

page A-1

This appendix supplies important information

regarding supported and not supported optical

splitter configurations in the 10GBE

environment.

Autres manuels pour SCE8000 GBE

Table des matières

Autres manuels Cisco Matériel réseau

Cisco

Cisco ONS 15454 Feuille d'instructions

Cisco

Cisco MXE 3000 Manuel

Cisco

Cisco 5400 Series Mode d’emploi

Cisco

Cisco IDS-4230-FE - Intrusion Detection Sys Fast Ethernet... Manuel de l'opérateur

Cisco

Cisco CSS11501 - 100Mbps Ethernet Load Balancing... Manuel utilisateur

Cisco

Cisco AGS+ Mode d’emploi

Cisco

Cisco TelePresence Manuel de service

Cisco

Cisco Cisco ASA Series Manuel utilisateur

Cisco

Cisco Network Adapter VIP-FE-TX/4E Manuel de l'opérateur

Cisco

Cisco NCS 2000 series Manuel utilisateur

Cisco

Cisco Prisma EtherLinX Manuel utilisateur

Cisco

Cisco NSS2000 - Gigabit Storage System Chassis Comment utiliser

Cisco

Cisco Firepower 1100 Series Manuel

Cisco

Cisco PIX Series Manuel

Cisco

Cisco 220 Series Smart Plus Manuel utilisateur

Cisco

Cisco ASR 5500 Mode d’emploi

Cisco

Cisco OSM-12CT3/T1 - Optical Services Module... Guide rapide

Cisco

Cisco Firepower 4100 Series Manuel utilisateur

Cisco

Cisco MERAKI MR57 Manuel utilisateur

Cisco

Cisco AIR-WLC2106-K9 - Wireless LAN Controller... Manuel utilisateur

Cisco

Cisco GRP= Guide rapide

Cisco

Cisco Firepower 9300 Manuel

Cisco

Cisco CTM GateWay Guide d'installation

Cisco

Cisco Firepower 2130 Guide de maintenance et de service

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur