CHIEF MSP-DCCPPNR Manuel utilisateur

Part # MSP-DCCPPNR

Large Flat Panel Dual Arm Wall Mount

The MSP-DCCPPNR is wall-mounted, rugged, versa-

tile, and installer-friendly. The mount is compatible

with the standard (14” x 14”) PSB interface bracket in

which a display can be mounted in either the land-

scape or portrait position on the mount.

The dual arms on the MSP-DCCPPNR:

• Extend from the wall 24-7/8” in length

• Pivot up to 90º left or right of center

The standard mount is shipped with the support posts

for the dual arms centered in the mount. The support

posts can be moved laterally right or left of center to

readily accommodate sites with limited wall space.

The mount also has two inches of height adjustment.

The tilt range for the display is 5º up and 15º down.

The MSP-DCCPPNR was designed for fast installa-

tion. After drawing the plumb line and installing the

two top lag bolts into the dual wall studs, the installer

hangs the mount on its top bracket and installs two lag

bolts in the bottom bracket. Next, the installer makes

the height adjustment, mounts the display, and con-

nects the power/audio/video cables, which are

diverted into the built-in path in the swing-out arms.

After making the lateral, rotational, and tilt adjust-

ments, the installation process is complete.

BEFORE YOU BEGIN

•Caution: To prevent damage to the PNR, which could affect or void the Factory warranty, and to the equip-

ment that will be attached to it, thoroughly study all instructions and illustrations before you begin the

installation. Pay particular attention to the “Important Warnings and Cautions” on Page 2.

• The combined weight of the components installed on the PNR must not exceed 200 lbs. (90.72kg).

• The PNR wall mount must be installed on dual wall studs or supporting framework. The wall to which the PNR is

anchored must be capable of supporting five times the total weight of the mount and all attached equipment.

• If a defect is discovered after Dell’s initial 21 day Customer Satisfaction period, Chief Mfg. will, at its option, repair

or replace the product at no charge provided it is returned during the warranty period. Please note contact informa-

tion for Chief Mfg. listed below:

CHIEF MANUFACTURING INC.

1-800-582-6480 952-894-6280 FAX 952-894-6918

8401 EAGLE CREEK PARKWAY, STE. 700

SAVAGE, MINNESOTA 55378 USA

PART NO. 8805-000146 (Rev. B)

2005 Chief Manufacturing

www.chiefmfg.com

10/05

INSTALLATION INSTRUCTIONS

Installation Instructions MSP-DCCPPNR

IMPORTANT WARNINGS AND CAUTIONS!

WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.

CAUTION: ACAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the cor-

responding instructions.

•WARNING: Improper installation can result in serious personal injury! Make sure that the structural members can

support a redundant weight factor five times the total weight of the equipment: if not, reinforce the

structure before installing the mount.

•WARNING: Be aware also of the potential for personal injury or damage to the unit if it is not adequately mounted.

•WARNING: The installer is responsible for verifying that the wall to which the mount is anchored will safely support

the combined load of all attached components or other equipment.

•WARNING: The weight of the display placed on the mount must not exceed 200 lbs. (90.72kg), the maximum load

capacity of the mount.

•WARNING: Watch for pinch points. Do not put your fingers between movable parts.

•WARNING: Make sure the mount and brackets are correctly oriented.

•WARNING: Make sure the flag securing the display is completely lowered at all times except when removing or

installing the display.

•CAUTION: Check the unit for shipping damage before you begin the installation.

NOTE: Hardware for attaching this unit to the wall is not supplied.

CONTENTS

IMPORTANT WARNINGS AND CAUTIONS! ..................................... 2

DIMENSIONAL DRAWING ................................................................. 3

INSPECT THE UNIT BEFORE INSTALLING ..................................... 4

MOUNT SPECIFICATIONS ................................................................ 4

INTERFACES ..................................................................................... 4

TOOLS REQUIRED FOR INSTALLATION ......................................... 4

PARTS LIST ....................................................................................... 4

MOUNT INSTALLATION .................................................................... 5

Mount the mount ........................................................................... 6

Adjust Height on the mount .......................................................... 7

MOUNT THE DISPLAY ...................................................................... 8

CABLE MANAGEMENT ..................................................................... 9

TENSION ADJUSTMENTS ................................................................ 10

Vertical Tilt Tension Adjustment ................................................... 10

Lateral Tilt Tension Adjustment .................................................... 10

Rotational Tilt Tension Adjustment ............................................... 10

SWING ARM ADJUSTMENTS ........................................................... 11

Adjusting the Swing Arms Slightly Off Center Adjustment ........... 11

Reconfiguring the Swing Arms to the Left or Right of Center ....... 12

REMOVE THE DISPLAY .................................................................... 12

Swing Arm Tension Adjustment........................................................... 13

Installation Instructions MSP-DCCPPNR

DIMENSIONAL DRAWING

Installation Instructions MSP-DCCPPNR

INSPECT THE UNIT BEFORE

INSTALLING

WARNING:Watch for pinch points. Do not put your fin-

gers between movable parts.

1. Carefully inspect the mount for shipping damage. If any

damage is apparent, call your carrier claims agent and

do not continue with the installation until the carrier has

reviewed the damage.

NOTE: Read all instructions before starting installation.

2. Lay out components to ensure you have all the required

parts before proceeding. See “DIMENSIONAL DRAW-

ING” on page 3.

MOUNT SPECIFICATIONS

Table 1 on page 4 provides the mount specificiations.

*Dimension does not include the PSB interface bracket.

INTERFACES

Table 2 on page 4 provides the applicable mount interfaces.

TOOLS REQUIRED FOR

INSTALLATION

• Allen wrench set

• Drill and bit set

• Wrench set

NOTE:Other tools may be required depending on the

method of installation.

PARTS LIST

Unpack the carton and verify the contents listed in Table 3 on

page 4. If you are missing any of the listed parts, contact

Customer Service at: 1-800-582-6480.

Table 1: Mount Specifications

Model Max Support Weight

mount

Extended

from Wall

mount 200 lbs. (90.72kg) 24-7/8”*

Table 2: mount Interfaces

Model Interfaces

mount 14” x 14” Plasma Static Brackets (PSB)

Table 3: Parts List

REF DESCRIPTION QTY

10 Wall Mount 1

20 Cover Plates 2

30 End Caps 4

40 Adjustment Wrench (not shown) 1

50 Tiewraps 12

— Lag Bolts (required, not supplied) 4

— Flat Washer (required, not supplied) 4

Installation Instructions MSP-DCCPPNR

MOUNT INSTALLATION

WARNING:Improper installation can result in serious

personal injury!

WARNING:It is the responsibility of the installer to verify

that the wall to which the mount is anchored

will safely support five times the combined

load of all attached components and equip-

ment. If not, reinforce the structure before

installing the mount.

Locate two wood studs 16” apart on center

1. Determine the exact mounting location prior to installa-

tion, considering screen size and the unit’s total swing

arm radius. Keep in mind that the mount must be

mounted to wood studs that are 16” apart on center.

NOTE: Mount the mount between parallel wall studs

or other supporting framework that is vertical

or horizontal.

2. Using a stud sensor, locate the two wood studs where

you will install the mount.

3. Draw a level plumb line to indicate the desired height of

the top mounting bracket.

4. With an assistant, lift and hold the mount against wall.

Use a pencil, awl, or small nail to mark the mounting

holes where two pilot holes will be drilled into the cen-

ter of the wood studs. Make sure the mounting holes are

level.

5. With an assistant, lay the mount down on the floor.

6. Drill two pilot holes where the mounting holes were

marked for anchoring the top bracket on the mount. See

Figure 1.

NOTE: Do not tighten the lag bolts down at this time.

Leave enough space between the wall and lag

bolts to hang the mount.

7. Install two lag bolts and two flat washers, in the pilot

holes drilled in step 6.

Figure 1. Two Wood Studs 16” Apart On Center

16”

Wood Studs

Pilot Holes

Wall

Installation Instructions MSP-DCCPPNR

Mount the mount

1. Mount the top bracket on the mount, as follows:

WARNING:Improper installation can result in serious

personal injury!

a. With an assistant, lift and hang the mount on the

two lag bolts and washers previously installed on

the wall. See Figure 2.

NOTE: Make sure washers are installed in front of the

top bracket, not behind the bracket.

b. Slide the mount into the desired position on the

wall and tighten the two lag bolts.

2. Mount the bottom bracket on the mount, as follows:

a. Mark the two mounting holes in the bottom

mounting bracket (see Figure 3). Make sure to

align the holes parallel to the holes drilled in the

top bracket.

b. Drill two pilot holes in the wall studs.

c. Install two lag bolts and two washers into the

pilot holes.

d. Tighten the two lag bolts.

Mount (Hang) the mount on Lag Bolts

Figure 2. Mount mount on Lag Bolts

Use Lag Bolts and Washers to Fasten mount to the Wall.

Figure 3. Mount Bottom Bracket on mount

Installation Instructions MSP-DCCPPNR

Figure 4. Adjust Height

Cover Plate (20)

End Caps (30)

Bottom Mounting Bracket

Figure 5. Install Cover Plates and End Caps

Adjust Height on the mount

NOTE: Height adjustment range up to 2 inches.

To adjust the mount height, do the following:

1. Check mount for the desired height. If needed, use the

adjustment wrench (40) to adjust the mount height.

2. To adjust the mount height, do the following:

• Turn adjustment nut (see Figure 4) clockwise (CW) to

lower the unit height, or

• Turn adjustment nut counterclockwise (CCW) to raise

the unit height.

Install Cover Plates and End Caps

NOTE: The cover plates and end caps have pressure

fitting ends that lock in place with each other.

1. Install cover plate (20) over the top bracket. See Figure 5.

2. Install end cap (30) on the cover plate (20). See Figure 5.

3. Repeat steps 1 and 2 for the bottom mounting bracket.

See Figure 5.

Adjustment Nut

1) Check mount height.

2) To adjust height, turn adjustment screw,

as follows:

• CW lowers the unit

• CCW raises the unit

Installation Instructions MSP-DCCPPNR

MOUNT THE DISPLAY

1. Make sure power is not supplied (turned off) to the display

and the locking device is in the unlocked (down) position

(see Figure 6) before attempting to mount the display.

2. Following the instructions for mounting the PSB interface

bracket of your specific plasma display panel, install the

mounting bracket on your plasma display panel.

WARNING:Watch for pinch points. Do not put your fin-

gers between movable parts.

3. With an assistant, slide the display down over the mount.

Make sure buttons of PSB interface bracket fully engage

all teardrop slots of the mount.

4. Secure the mounting bracket to the mount by completely

engaging the locking device (see Figure 6).

WARNING:Make sure the locking device securing the dis-

play is completely engaged at all times except

when removing or installing the display. The

locking device must be completely engaged

during installation/removal of cables when the

display is mounted.

NOTE: A padlock may be used on the locking device for

increased security.

5. Connect and secure power/audio/video cables, making

sure to leave sufficient slack to allow for movement of the

swing arms.

Figure 6. Locking Device

Lock

Unlock

PSB

Teardrop

Slot

(Typical)

Bracket

Interface

Installation Instructions MSP-DCCPPNR

CABLE MANAGEMENT

WARNING:Make sure your cables do notrun through

a pinch point.

1. Route power/audio/video cables through the cable channel

in top arm (see Figure 7), allowing sufficient slack in

cables for extension and avoiding pinch points, and secure

cables using two clips and two tiewraps (50, not shown).

2. Route power/audio/video cables along bottom arm (see

Figure 8), using tiewraps (50, not shown) to secure cables

to each arm, and through cable channel.

CAUTION: To prevent equipment damage, do not route

cables through holes in the display mounting

plate.

3. Route power/audio/video cables to an open area behind

the mounting plate (not shown). Leave a sufficient amount

of slack in cables to allow for connection and extension

where needed.

Cables

Tiewraps

Top Cable

Management Channel

Figure 7. Cable Management Channel (Top)

Bottom Cable

Management Channel

Figure 8. Cable Management Channel (Bottom)

Installation Instructions MSP-DCCPPNR

TENSION ADJUSTMENTS

Vertical Tilt Tension Adjustment

1. Using 5/32” Allen wrench, slightly tighten or loosen two

screws, one on each side, equally (see Figure 9).

2. With display mounted, check for desired vertical tilt ten-

sion.

3. Repeat Step 1 and Step 2 until desired vertical tilt tension

is obtained.

Lateral Tilt Tension Adjustment

CAUTION: Overtightening lateral adjustment will cause

excessive wear and may distort adjustment

components.

1. Using a 9/16” wrench, slightly tighten or loosen lateral tilt

tension adjustment nut (see Figure 10).

2. Mount the display and check for desired tilt tension.

3. Repeat Steps 1 and 2 until desired tilt tension is obtained.

Rotational Tilt Tension Adjustment

1. If necessary, loosen or tighten bottom rotational tilt

tension adjustment nut (see Figure 11).

2. Mount the display and check for desired rotational tilt ten-

sion.

3. Repeat Steps 1 and 2 until desired rotational tilt tension is

obtained.

Adjustment

Nut

Vertical Tilt

Adj. Screw

Figure 9. Vertical Tilt

Lateral Tilt

Adjustment Nut

Figure 10. Lateral Tilt

Rotational

Adj. Nut

Figure 11. Rotational Adjustment

Table des matières

Autres manuels CHIEF Support et étagère

CHIEF

CHIEF SSB-257 Manuel utilisateur

CHIEF

CHIEF ODMLT Manuel utilisateur

CHIEF

CHIEF RPA4000 Manuel utilisateur

CHIEF

CHIEF KFCD-110 Manuel utilisateur

CHIEF

CHIEF K1S Series Manuel utilisateur

CHIEF

CHIEF K0 Series Manuel utilisateur

CHIEF

CHIEF FHB3047 Manuel utilisateur

CHIEF

CHIEF FHB5039 Manuel utilisateur

CHIEF

CHIEF JHS Series Manuel utilisateur

CHIEF

CHIEF YAMF1 Manuel utilisateur

CHIEF

CHIEF JWDSK210 Manuel utilisateur

CHIEF

CHIEF PAC511 Manuel utilisateur

CHIEF

CHIEF K1C100 Manuel utilisateur

CHIEF

CHIEF PNR Manuel utilisateur

CHIEF

CHIEF PACCC1 Manuel utilisateur

CHIEF

CHIEF HB-011E Manuel utilisateur

CHIEF

CHIEF FPD-110 Manuel utilisateur

CHIEF

CHIEF Structural Ceiling Plate with Flex Joint... Manuel utilisateur

CHIEF

CHIEF OFB214 Manuel utilisateur

CHIEF

CHIEF WM-100 Manuel utilisateur

CHIEF

CHIEF MF1 Series Manuel utilisateur

CHIEF

CHIEF MCS6000 Series Manuel utilisateur

CHIEF

CHIEF CM7W12U Manuel utilisateur

CHIEF

CHIEF RPA145 Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur