Cabletron Systems ESXMIM Manuel utilisateur

ESXMIM/ESXMIM-F2

ETHERNET SWITCH

MODULE

INSTALLATION GUIDE

ICH1Book Page 1 Thursday, April 18, 1996 7:21 AM

ICH1Book Page 2 Thursday, April 18, 1996 7:21 AM

ESXMIM/ESXMIM-F2 Installation Guide i

NOTICE

Cabletron Systems reserves the right to make changes in specifications and other information

contained in this document without prior notice. The reader should in all cases consult Cabletron

Systems to determine whether any such changes have been made.

The hardware, firmware, or software described in this manual is subject to change without notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL,

INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT

NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR

THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN

ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH

DAMAGES.

Printed in the United States of America

Order Number: 9031098-03 February 2000

ESXMIM, ESXMIM-F2, SPECTRUM,LANVIEW,SPECTRUM Element Manager,

MicroMMAC,MMAC,Flexible Network Bus,and BRIM are registered trademarks and Element

Manager,EPIM,APIM,andFPIM are trademarks of Cabletron Systems, Inc.

All other product names mentioned in this manual may be trademarks or registered trademarks of

their respective companies.

FCC NOTICE

This device complies with Part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable

protectionagainst harmfulinterference when the equipment is operated in a commercial environment.

This equipment uses, generates, and can radiate radio frequency energy and if not installed in

accordance with the operator’s manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause interference in which case the user

will be required to correct the interference at his own expense.

WARNING: Changes or modifications made to this device which are not expressly approved by the

party responsible for compliance could void the user’s authority to operate the equipment.

Printedon RecycledPaper

Notice

ii ESXMIM/ESXMIM-F2 Installation Guide

DOC NOTICE

This digital apparatus does not exceed the ClassA limits for radio noise emissions from digital

apparatus set out in the Radio Interference Regulations of the Canadian Department of

Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables

aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique

édicté par le ministère des Communications du Canada.

VCCI NOTICE

This equipment is in the 1st Class Category (information equipment to be used in commercial and/or

industrial areas) and conforms to the standards set by the Voluntary Control Council for Interference

by Information Technology Equipment (VCCI) aimed at preventing radio interference in commercial

and/or industrial areas.

Consequently, when used in a residential area or in an adjacent area thereto, radio interference may be

caused to radios and TV receivers, etc.

Read the instructions for correct handling.

CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT

IMPORTANT:

Before utilizing this product, carefully read this License Agreement.

This document is an agreement between you, the end user, and Cabletron Systems, Inc. (“Cabletron”)

that sets forth your rights and obligations with respect to the Cabletron software program (the

“Program”) contained in this package. The Program may be contained in ﬁrmware, chips or other

media. BY UTILIZING THE ENCLOSED PRODUCT,YOU ARE AGREEING TO BECOME

BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND

THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IFYOU DO NOT

AGREE TO THE TERMS OF THIS AGREEMENT, PROMPTLY RETURN THE UNUSED

PRODUCT TO THE PLACE OF PURCHASE FOR A FULL REFUND.

ICH1Book Page ii Thursday, April 18, 1996 7:21 AM

Notice

ESXMIM/ESXMIM-F2 Installation Guide iii

CABLETRON SOFTWARE PROGRAM LICENSE

1. LICENSE. You have the right to use only the one (1) copy of the Program provided in this

package subject to the terms and conditions of this License Agreement.

You may not copy, reproduce or transmit any part of the Program except as permitted by the

2. OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the

Program.

3. APPLICABLE LAW. This License Agreement shall be interpreted and governed under the laws

and in the state and federal courts of New Hampshire. You accept the personal jurisdiction and

venue of the New Hampshire courts.

EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY

1. EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in

writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including

its documentation and media).

CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO

YOU BY CABLETRON IN WRITING, EITHER EXPRESSED OR IMPLIED, INCLUDING

BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE

ACCOMPANYING WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.

2. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL

CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER

(INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS,

PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL,

INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS)

ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT,

EVEN IF CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH

DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR

LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR

ON THE DURATION OR LIMITATION OF IMPLIED WARRANTIES, IN SOME

INSTANCES THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO

YOU.

UNITED STATES GOVERNMENT RESTRICTED RIGHTS

The enclosed product (a) was developed solely at private expense; (b) contains “restricted computer

software” submitted with restricted rights in accordance with Section 52227-19 (a) through (d) of the

Commercial Computer Software - Restricted Rights Clause and its successors, and (c) in all respects

is proprietary data belonging to Cabletron and/or its suppliers.

For Department of Defense units, the product is licensed with “Restricted Rights” as deﬁned in the

DoD Supplement to the Federal Acquisition Regulations, Section 52.227-7013 (c) (1) (ii) and its

successors, and use, duplication, disclosure by the Government is subject to restrictions as set forth in

subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at

252.227-7013. Cabletron Systems, Inc., 35 Industrial Way, Rochester, New Hampshire 03867-0505.

ICH1Book Page iii Thursday, April 18, 1996 7:21 AM

Notice

iv ESXMIM/ESXMIM-F2 Installation Guide

DECLARATION OF CONFORMITY

Application of Council Directive(s): 89/336/EEC

73/23/EEC

Manufacturer’s Name: Cabletron Systems, Inc.

Manufacturer’s Address: 35 Industrial Way

PO Box 5005

Rochester, NH 03867

European Representative Name: Mr.J.Solari

European Representative Address: Cabletron Systems Limited

Nexus House, Newbury Business Park

London Road, Newbury

Berkshire RG14 2PZ, England

Conformance to Directive(s)/Product Standards: EC Directive 89/336/EEC

EC Directive 73/23/EEC

EN 55022

EN 50082-1

EN 60950

Equipment Type/Environment: Networking Equipment, for use in a

Commercial or Light Industrial

Environment.

We the undersigned, hereby declare that the equipment packaged with this notice conforms to

the above directives.

Manufacturer Legal Representative in Europe

Mr. Richard Michaud Mr. J. Solari

___________________________________ ___________________________________

Full Name Full Name

Manager of Engineering Services Managing Director - E.M.E.A.

___________________________________ ___________________________________

Title Title

Rochester, NH, USA Newbury, Berkshire, England

___________________________________ ___________________________________

Location Location

ESXMIM/ESXMIM-F2 Installation Guide v

CONTENTS

CHAPTER 1 INTRODUCTION

1.1 How to Use This Manual.............................................................1-1

1.2 ESXMIM Overview......................................................................1-2

1.3 Document Conventions...............................................................1-3

1.3.1 Warnings and Notifications.............................................1-3

1.3.2 Document Format...........................................................1-3

1.4 Related Documents.....................................................................1-4

1.5 Getting Help.................................................................................1-4

CHAPTER 2 CONTROLS AND INDICATORS

2.1 Parts of the ESXMIM...................................................................2-1

2.1.1 The Faceplate.................................................................2-1

2.1.2 Internal Components......................................................2-4

2.1.3 LANVIEW LEDs..............................................................2-6

CHAPTER 3 INSTALLATION

3.1 Unpacking the ESXMIM..............................................................3-1

3.2 Setting Mode Switches................................................................3-3

3.3 Pre-Installation Test.....................................................................3-6

3.4 Installation...................................................................................3-8

3.5 Connecting to the Network........................................................3-11

3.5.1 Connecting a 10BASE-T Segment to the ESXMIM......3-12

3.5.2 Connecting a 10BASE-F Segment to the ESXMIM-F2.3-14

3.5.3 Connecting a 10BASE-T Segment to an EPIM-T.........3-16

3.5.4 Connecting a 10BASE-F Segment to an EPIM-F2 or

EPIM-F3........................................................................3-19

3.5.5 Connecting a 10BASE-F Segment to an EPIM-F1.......3-21

3.5.6 Connecting an AUI Segment to an EPIM-X or EPIM-A3-23

3.5.7 Connecting a 10BASE2 Segment to an EPIM-C..........3-24

3.6 Backplane Test..........................................................................3-26

CHAPTER 4 TROUBLESHOOTING

4.1 Using LANView LEDs..................................................................4-1

4.2 Troubleshooting Checklist...........................................................4-3

4.3 Using The Reset Switch..............................................................4-5

ICH1Book Page v Thursday, April 18, 1996 7:21 AM

Contents

vi ESXMIM/ESXMIM-F2 Installation Guide

APPENDIX A SPECIFICATIONS

A.1 Physical Properties ..................................................................... A-1

A.2 Operating Properties...................................................................A-1

A.3 Environmental Requirements......................................................A-2

A.4 Certification................................................................................. A-2

A.5 COM Port Pinout.........................................................................A-2

APPENDIX B BRIM/EPIM INFORMATION

B.1 ESXMIM-Capable BRIMs ...........................................................B-1

B.2 ESXMIM-Capable EPIMs............................................................B-3

APPENDIX C UPGRADING THE ESXMIM

C.1 Locating BRIM Connectors.........................................................C-1

C.2 Adding EPIMs .............................................................................C-2

C.3 SIMM Upgrades..........................................................................C-3

C.3.1 Locating SIMMs..............................................................C-3

C.3.2 Installing SIMMs .............................................................C-4

C.3.2.1 Installing a FLASH SIMM...............................C-5

C.3.2.2 Installing an SDRAM or LDRAM SIMM..........C-6

APPENDIX D ETHERNET CABLING REQUIREMENTS

D.1 Network Requirements ...............................................................D-1

D.1.1 10BASE-T Twisted Pair Network....................................D-1

D.1.2 Multimode Fiber Optic Network ......................................D-3

D.1.3 Single Mode Fiber Optic Network...................................D-4

D.1.4 10BASE2 Coaxial Cable Network...................................D-5

D.1.5 Transceiver Requirements..............................................D-5

INDEX

ICH1Book Page vi Thursday, April 18, 1996 7:21 AM

ESXMIM/ESXMIM-F2 Installation Guide 1-1

CHAPTER 1

INTRODUCTION

Welcome to the Cabletron Systems

ESXMIM/ESXMIM-F2 Ethernet

Switch Module Installation Guide

. This manual provides installation

instructions and reference information for the ESXMIM and

ESXMIM-F2 Ethernet Switching Media Interface Modules.

1.1 HOW TO USETHIS MANUAL

To gain a full understanding of this device and its capabilities, and to help

eliminate any potential problems during or after installation, please be

sure to read and understand all of the instructions/information in this

document and in the release notes supplied with your ESXMIM.

You should have a general working knowledge of Ethernet or IEEE 802.3

type data networks prior to installing the ESXMIM. The following

summarizes the organization of this manual.

Chapter 1,

Introduction

, discusses the use and conventions of the

ESXMIM/ESXMIM-F2 Ethernet Switch Module Installation Guide

details the procedures to follow for obtaining assistance from Cabletron

Systems, and provides a list of related documentation.

Chapter 2,

Controls and Indicators

, identiﬁes and describes the

components and monitoring indicators that make up the ESXMIM. This

chapter contains information that is essential to the understanding of the

procedures in the rest of this manual.

Chapter 3,

Installation

, details the procedures to follow when unpacking,

testing, and installing the ESXMIM. The chapter contains information

and step-by-step instructions for connecting network cabling to the

ESXMIM and closes with a procedure which may be used to test the

operation of the ESXMIM in the network.

NOTE

This manual covers both the ESXMIM and the ESXMIM-F2.

The name ESXMIM will be used to refer to both of the modules

unless it is necessary to describe features that are unique to a

speciﬁc module.

ICH1Book Page 1 Thursday, April 18, 1996 7:21 AM

Chapter 1:

Introduction

1-2 ESXMIM/ESXMIM-F2 Installation Guide

Chapter 4,

Troubleshooting

, describes how to use LANVIEW LEDs on

the ESXMIM. The chapter deﬁnes the different LED conditions and

provides a table of simple troubleshooting instructions for module-related

difﬁculties.

Appendix A,

Specifications

, provides the physical speciﬁcations and

operating requirements of the ESXMIM. This appendix also contains

serial port pinout tables for constructing Local Management cables.

Appendix B,

BRIM/EPIM Information

, describes two series of modules

called BRIMs and EPIMs, which may be added to the ESXMIM to

provide additional capabilities or connectivity options.

Appendix C,

Upgrading the ESXMIM

, details the procedures that must

be followed when expanding the capabilities of the ESXMIM. This

appendix contains information on memory upgrades and the addition of

EPIM modules to the ESXMIM.

Appendix D,

Ethernet Cabling Requirements

, describes the test

characteristics that Ethernet cables must adhere to in order to be

standards-compliant.Any Ethernet link or cable that is to be connected to

the ESXMIM should be veriﬁed to be within the speciﬁcations and

limitations provided in this appendix.

1.2 ESXMIM OVERVIEW

The ESXMIM and ESXMIM-F2 are multi-interface Ethernet switching

modules designed to provide maximum throughput while supplying

comprehensive network management functionality. The ESXMIM and

ESXMIM-F2 must be conﬁgured in a Cabletron Systems Multi Media

Access Center (MMAC) hub.

ICH1Book Page 2 Thursday, April 18, 1996 7:21 AM

Autres manuels pour ESXMIM

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Cabletron Systems Changer

Cabletron Systems

Cabletron Systems MICROMMAC-22T Manuel utilisateur

Cabletron Systems

Cabletron Systems MMAC-Plus 9H423-28 Manuel

Cabletron Systems

Cabletron Systems MMAC-Plus 9T122-24 Manuel utilisateur

Cabletron Systems

Cabletron Systems SEHI-22FL Manuel utilisateur

Cabletron Systems

Cabletron Systems MMAC-Plus 9H531-18 Manuel utilisateur

Cabletron Systems

Cabletron Systems STH 24 STH-24 Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartSwitch 2500 Manuel utilisateur

Cabletron Systems

Cabletron Systems bridges Manuel utilisateur

Cabletron Systems

Cabletron Systems MMAC-Plus 9T125-08 Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartSwitch 9W006 Manuel utilisateur

Cabletron Systems

Cabletron Systems ATX Manuel utilisateur

Cabletron Systems

Cabletron Systems MMAC-Plus 9H423-26 Manuel

Cabletron Systems

Cabletron Systems SmartSTACK 100 ELS100-16TX Manuel utilisateur

Cabletron Systems

Cabletron Systems SPECTRUM 1800 Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartCell 6A000 Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartSTACK ELS10-27MDU Instructions d'installation et d'utilisation

Cabletron Systems

Cabletron Systems 9G421-02 Document technique

Cabletron Systems

Cabletron Systems 24 Manuel utilisateur

Cabletron Systems

Cabletron Systems CSX200 CyberSWITCH Manuel utilisateur

Cabletron Systems

Cabletron Systems SynOptics 3000 Series Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartSwitch SBU128 Manuel utilisateur

Cabletron Systems

Cabletron Systems SEHI-22 Manuel utilisateur

Cabletron Systems

Cabletron Systems 9F426-03 Manuel utilisateur

Cabletron Systems

Cabletron Systems MMAC-Plus 9F206-02 Document technique

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur