Cabletron Systems MMAC-Plus 9H423-26 Manuel

9032227-01

SmartSwitch 9000

9H423-26

Local Management Appendix

Appendix

9H423-26 Module Speciﬁc

Information

Introduction

This appendix contains local management information that is speciﬁc to the

9H423-26 Fast Ethernet Switch Module.

The 9H423-26 Switch Module has 26 ports:

• 24 ports (two ﬁxed RJ21 connectors)

• 2 ports (two ﬁxed MMF SC connectors)

This module can operate in either full duplex or half duplex mode.

Auto-negotiation provides support for 10 Mbps and 100 Mbps speeds at both half

and full duplex. 100Base-FX supports 100 Mbps speed at both half and full

duplex.

Auto-negotiation allows the module to automatically use the fastest rate

supported by the device at the other end (either 10 Mbps or 100 Mbps at either

half or full duplex). This technology is similar to how modems negotiate

transmission speed to ﬁnd the highest transmission rate. Similarly,

auto-negotiation determines the highest common speed between two devices and

communicates at that speed. If no common speed is detected, the device will be

partitioned.

Modifying Fields and User Privileges

To modify ﬁelds on this module, you must have read-write or super-user

privileges. If you have read-only privileges, you can view information; however,

you cannot modify any ﬁelds. For more information about user privileges and

community names, see the

SmartSwitch 9000 Module Local Management User’s

Guide.

9H423-26 Module Speciﬁc Information

Module Interfaces

The 9H423-26 Fast Ethernet Switch Module has 31 interfaces. Table 1 lists the

identifying number, name, and description of each interface.

Table 1. 9H423-26 Module Interfaces

Interface

Number

Interface

Name

Interface

Description

1 SMB1 1 Mbps System Management Bus

2 SMB10 10 Mbps System Management Bus

3 HOST

4 LOCAL

5 INB Internal Network Bus

6 FENET1 Fast Ethernet Front Panel Port 1

7 FENET2 Fast Ethernet Front Panel Port 2

8 FENET3 Fast Ethernet Front Panel Port 3

9 FENET4 Fast Ethernet Front Panel Port 4

10 FENET5 Fast Ethernet Front Panel Port 5

11 FENET6 Fast Ethernet Front Panel Port 6

12 FENET7 Fast Ethernet Front Panel Port 7

13 FENET8 Fast Ethernet Front Panel Port 8

14 FENET9 Fast Ethernet Front Panel Port 9

15 FENET10 Fast Ethernet Front Panel Port 10

16 FENET11 Fast Ethernet Front Panel Port 11

17 FENET12 Fast Ethernet Front Panel Port 12

18 FENET13 Fast Ethernet Front Panel Port 13

19 FENET14 Fast Ethernet Front Panel Port 14

20 FENET15 Fast Ethernet Front Panel Port 15

21 FENET16 Fast Ethernet Front Panel Port 16

22 FENET17 Fast Ethernet Front Panel Port 17

23 FENET18 Fast Ethernet Front Panel Port 18

9H423-26 Module Speciﬁc Information

Use the numbers listed in Table 1 to conﬁgure the module’s default interface (see

the General Conﬁguration Screen).

24 FENET19 Fast Ethernet Front Panel Port 19

25 FENET20 Fast Ethernet Front Panel Port 20

26 FENET21 Fast Ethernet Front Panel Port 21

27 FENET22 Fast Ethernet Front Panel Port 22

28 FENET23 Fast Ethernet Front Panel Port 23

29 FENET24 Fast Ethernet Front Panel Port 24

30 FENET25 Fast Ethernet Front Panel Port 25 (Fiber)

31 FENET26 Fast Ethernet Front Panel Port 26 (Fiber)

Table 1. 9H423-26 Module Interfaces (Continued)

Interface

Number

Interface

Name

Interface

Description

9H423-26 Module Speciﬁc Information

Port Conﬁguration Screen

The 9H423-26 Port Conﬁguration Screen (Figure 1), displays conﬁguration

information about each port on the module (one port at a time).

Figure 1. 9H423-26 Port Conﬁguration Screen

SmartSwitch 9000 Local Management

Port Configuration

Module Name: 9H423-26 Firmware Revision: 01.00.00

Slot Number: 1 BOOTPROM Revision: 01.00.00

PORT #: 1

Port Type RJ21

Link Status Link

Current Operation Mode 100Base-TXFD

Desired Operation Mode [Auto-Negotiation]

Advertised Ability [100Base-TXFD] [Enabled]

SAVE [PORT: 1] EXIT RETURN

9H423-26 Module Speciﬁc Information

Port Conﬁguration Screen Fields

The following information brieﬂy explains each Port Conﬁguration Screen ﬁeld.

Slot # (Modiﬁable)

Indicates the slot that the board occupies in the chassis.

Port #

(Read-only

)

Indicates the current port for which statistics are displayed.

PortType

(Read-only)

Displays one of the following values:

• MMF SC

• RJ21

Link Status

(Read-only)

Displays one of the following values:

• Link

• No Link

• N/A

Current Operation Mode

(Read-only)

Displays one of the following values:

• 10Base-T

Operating standard 10 Mbps Ethernet over two pairs of UTP cable.

• 10Base-TFD

Operating Full Duplex 10 Mbps Ethernet over two pairs of UTP cable. Full

Duplex indicates the module is connected to a single device, and is not

listening for other transmissions or collisions when sending data. This allows

both devices on the link to send and receive data simultaneously over the link.

Theoretically, this provides the devices with twice the bandwidth of normal,

or half duplex, Ethernet.

• 100Base-TX

Operating Fast Ethernet over two pairs of Category 5 UTP or Type 1 STP

cable.

• 100Base-TXFD

Operating Full Duplex 100 Mbps Fast Ethernet over two pairs of Category 5

UTP or Type 1 STP cable.

• 100Base-FX

Operating 100 Mbps Fast Ethernet over two strands of multimode ﬁber cable.

• 100Base-FXFD

9H423-26 Module Speciﬁc Information

Operating Full Duplex 100 Mbps Fast Ethernet over two strands of multimode

ﬁber cable.

Desired Operation Mode

(Toggle)

Displays one of the following values:

• Auto-Negotiation

• 10Base-T manual

• 10Base-TFD manual

• 100Base-TX manual

• 100Base-TXFD manual

• 100Base-FX manual

• 100Base-FXFD manual

Only the modes that the device is capable of using are displayed. The module

defaults to auto-negotiation. If the device connected to the module also supports

auto-negotiation, the devices self-conﬁgure to the fastest possible speed and

duplex. For example, if the other device does not support auto-negotiation, the

devices do a parallel detection and conﬁgure to either 10 Mbps or 100 Mbps, but

only at half duplex. If the device connected to the module is standard Ethernet

with no auto-negotiation support, and is conﬁgured for full duplex, the Desired

Operation Mode ﬁeld must be set to 10Base-T Full Duplex.

Advertised Ability

(2 Toggles)

Allows the user to specify the advertised ability for the chosen port. The ability of

each port is presented ﬁrst, followed by the ability to enable/disable on each port.

Advertised Ability is applicable only when the Desired Operation Mode ﬁeld is

set to Auto-Negotiation. Otherwise this ﬁeld displays N/A and is read-only.

When in auto-negotiation mode, the module auto-negotiates to the highest speed

being advertised by both devices.

Port #

(Modiﬁable)

Displays the current port for which conﬁguration information is displayed. Use

the procedure in the next section to display conﬁguration information for a

different port.

9H423-26 Module Speciﬁc Information

Displaying Conﬁguration Information for a Different Port

To display conﬁguration information for a different port:

1. Use the arrow keys to highlight the

Port #

ﬁeld at the bottom of the Port

Conﬁguration Screen.

2. Press the

Space

Bar

to increment (or press the

Delete

key to decrement) the

port number.

3. Press the

Return

key (neither the read-only

Port #

ﬁeld nor the conﬁguration

information will change until you press the

Return

key).

Exiting the Port Conﬁguration Screen

To exit the Port Conﬁguration Screen, use the arrow keys to highlight

RETURN

then press the Return key.

9H423-26 Module Speciﬁc Information

Port Statistics Screen

The 9H423-26 Port Statistics Screen (Figure 2), displays statistical information for

each port (one port at a time).

Figure 2. 9H423-26 Port Statistics Screen

SmartSwitch 9000 Local Management

Port Statistics

Module Name: 9H423-36 Firmware Revision: 01.02.X3

Slot Number: 1 BOOTPROM Revision: 01.00.01

PORT #: 1

Bytes: 3390336996 Link Status: Link

Frames: 49857191 Port Type: RJ21

Total Errors: 93 Admin Status: Enabled

Collisions: 87 Application: Bridging

CRC/Align Errors: 6 Operation Mode: 10Base-T Full Duplex

Undersize Packets: 0 Auto Negotiation: Yes

Oversize Packets: 0

Fragments: 87

Jabbers: 0

Broadcasts: 6

Multicast: 19090317

[Port: 1] EXIT RETURN

Autres manuels pour MMAC-Plus 9H423-26

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Cabletron Systems Changer

Cabletron Systems

Cabletron Systems FN100 Manuel utilisateur

Cabletron Systems

Cabletron Systems Fast Network 10 Manuel utilisateur

Cabletron Systems

Cabletron Systems DLEHF-MA Manuel utilisateur

Cabletron Systems

Cabletron Systems MMAC-Plus 9T125-24 Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartCell 6A000 Manuel utilisateur

Cabletron Systems

Cabletron Systems Cyber SWITCH 1000 Manuel utilisateur

Cabletron Systems

Cabletron Systems FRM Manuel utilisateur

Cabletron Systems

Cabletron Systems CyberSWITCH CSX150 Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartSwitch 8000 Manuel utilisateur

Cabletron Systems

Cabletron Systems MMAC-Plus 9E423-24 Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartSTACK EPIM1000-S1LX 1000BASE-LX Manuel utilisateur

Cabletron Systems

Cabletron Systems 9F122-12 Manuel utilisateur

Cabletron Systems

Cabletron Systems MiniMMAC Manuel utilisateur

Cabletron Systems

Cabletron Systems KBU 64 Manuel utilisateur

Cabletron Systems

Cabletron Systems MMAC-Plus SFCS-1000 Feuille d'instructions

Cabletron Systems

Cabletron Systems SmartSwitch 9000 Manuel utilisateur

Cabletron Systems

Cabletron Systems 9F120-08 Document technique

Cabletron Systems

Cabletron Systems SmartSTACK 100 ELS100-24TX Instructions d'installation et d'utilisation

Cabletron Systems

Cabletron Systems 9E133-36 Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartSTACK ELS100-8TXUF2 Manuel utilisateur

Cabletron Systems

Cabletron Systems FN100 Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartSwitch 9000 Document technique

Cabletron Systems

Cabletron Systems MMAC-Plus 9G426-02 Manuel utilisateur

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Instructions de montage

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur