Cabletron Systems MMAC-Plus 9E312-12 Manuel utilisateur

MMAC-Plus

™

9E312-12

Ethernet Switch Module

User’s Guide

Notice

Cabletron Systems reserves the right to make changes in speciﬁcations and other information

contained in this document without prior notice. The reader should in all cases consult Cabletron

Systems to determine whether any such changes have been made.

The hardware, ﬁrmware, or software described in this manual is subject to change without notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL, INDIRECT,

SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED

TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION

CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR

SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.

Cabletron Systems, Inc.

35 Industrial Way

Rochester, NH 03867-0505

Printed in the United States of America

Order Number: 9031405 May 1995

SPECTRUM

Remote LANVIEW

and

LANVIEW

are registered trademarks and

MMAC-Plus

trademark of Cabletron Systems, Inc.

Ethernet

is a trademark of Xerox Corporation and

i960

is a registered trademark of Intel Corporation.

Notice

FCC Notice

This device complies with Part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

NOTE:

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial environment.

This equipment uses, generates, and can radiate radio frequency energy and if not installed in

accordance with the operator’s manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause interference in which case the user

will be required to correct the interference at his own expense.

WARNING:

Changes or modiﬁcations made to this device which are not expressly approved by the

party responsible for compliance could void the user’s authority to operate the equipment.

VCCI Notice

This equipment is in the 1st Class Category (information equipment to be used in commercial and/or

industrial areas) and conforms to the standards set by the Voluntary Control Council for Interference

by Information Technology Equipment (VCCI) aimed at preventing radio interference in commercial

and/or industrial areas.

Consequently, when used in a residential area or in an adjacent area thereto, radio interference may be

caused to radios and TV receivers, etc.

Read the instructions for correct handling.

iii

Notice

DOC Notice

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital

apparatus set out in the Radio Interference Regulations of the Canadian Department of

Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables

aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique

édicté par le ministère des Communications du Canada.

Contents

Chapter 1 Introduction

Features........................................................................................................................... 1-2

Related Manuals............................................................................................................ 1-5

Getting Help .................................................................................................................. 1-5

Chapter 2 Installing the 9E312-12 Module

Pinouts............................................................................................................................ 2-3

The Reset Switch ........................................................................................................... 2-4

User Accessible Components ...................................................................................... 2-5

Setting the 9E312-12 Module DIP Switch.................................................................. 2-6

Chapter 3 Operation

ENIB................................................................................................................................ 3-2

Fast Packet Switch.........................................................................................................3-2

i960 Host......................................................................................................................... 3-2

INB NIB .......................................................................................................................... 3-3

System Management Buses ......................................................................................... 3-3

SMB-1 Bus ............................................................................................................... 3-3

SMB-10 Bus ............................................................................................................. 3-3

System Diagnostic Controller...................................................................................... 3-3

DC/DC Converter ........................................................................................................ 3-4

INB Interface.................................................................................................................. 3-4

Chapter 4 LANVIEW LEDs

Chapter 5 Speciﬁcations

Technical Speciﬁcations................................................................................................ 5-1

CPU:......................................................................................................................... 5-1

Memory: .................................................................................................................. 5-1

Standards: ............................................................................................................... 5-1

Network Interfaces: ............................................................................................... 5-1

Safety............................................................................................................................... 5-2

Service............................................................................................................................. 5-2

Contents

Physical...........................................................................................................................5-2

Dimensions: ............................................................................................................5-2

Weight:.....................................................................................................................5-2

Environment: ..........................................................................................................5-3

1-1

Chapter 1

Introduction

The 9E312-12 is a thirteen port switching module with twelve front panel Ethernet

interfaces and one Internal Network Bus (INB) backplane interface. This module

uses a Fast Packet Switch (FPS) hardware based switch design and an advanced

Intel i960

microprocessor. This microprocessor provides a platform for all

management functions within a scalable RISC-Based Architecture.

The module can operate in two modes; as a 12 port Ethernet bridge with a high

speed backbone connection or as 12 Ethernet connections to a Cabletron

SecureFast™ Packet Switch (SFPS). Each port of the 9E312-12 can be conﬁgured to

operate in the Full Duplex mode. This conﬁguration allows each port to provide a

full 20 Mbps of bandwidth.

Network management information is available through a variety of methods. All

information based on SNMP is accessible either via an in-band (Front Panel port),

Side Band (SMB-10), or via the EM’s COM ports using a Network Management

Server, and Serial Line Interface Protocol (SLIP) or Point-to-Point Protocol (PPP).

For more information on the SMB-10, SLIP or PPP refer to the MMAC-Plus Local

Management User’s Guide.

The 9E312-12 also features front panel LANVIEW™ Diagnostic LED’s to offer at-

a-glance status information about each front panel port as well as the operation of

the overall module.

Ethernet networks are connected to the 9E312-12 module using standard Ethernet

10 Base-T RJ-45 connectors on the front panel with connectivity for UTP and STP

links up to 100 meters in length.

Introduction

1-2

Features

Processor

The 9E312-12 is equipped with an advanced Intel i960 microprocessor. This

microprocessor provides a platform for all management functions such as

Spanning Tree, RMON, and MIB support within a scalable RISC-based

architecture.

Fast Packet Switching

The 9E312-12 incorporates a hardware based switch design referred to as a Fast

Packet Switch (FPS), a collection of custom ASICs designed speciﬁcally for high

speed switching. Because all frame translation, address lookups, and forwarding

decisions are performed in hardware, the 9E312-12 can obtain a throughput

performance of greater than 130K pps.

Management

The 9E312-12 features SNMP for local and remote management. Local

management is provided through the RS-232 Com ports on the MMAC-Plus

Environmental Module using a standard VT-220 terminal or emulator. Remote

management is possible through Cabletron’s SPECTRUM or any SNMP

compliant management tool. Included as management features are the IETF

Standard Management Information Base (MIBs) RMON (RFC1271), IETF MIB II

(RFC-1213), IETF Bridge MIB (RFC-1493), and a host of other Cabletron enterprise

MIBs. The 9E312-12 also offers the user a wide variety of statistical network

management information to enhance network planning and troubleshooting. This

module provides information for each front panel Ethernet 10Base-T port,

including packet counts along with errored frame information such as collisions,

CRCs, and Giants, via a variety of industry standard and private MIBS. Industry

standard IEEE 802.1d bridging, including Spanning Tree Algorithm, is supported.

Connectivity

The 9E312-12 module has one interface to the INB and twelve front panel Ethernet

connections. The INB interface is a ﬁxed connection to INB-1 which allows the

9E312-12 to communicate with other MMAC-Plus modules supporting various

LAN technologies including: Token Ring, FDDI, Ethernet, WAN and ATM. The

front panel Ethernet connections are via standard RJ-45 connectors supporting

UTP and STP cabling up to 100 meters in length.

1-3

Features

Management Information Base (MIB) Support

The 9E312-12 provides MIB support including:

• RMON (RFC-1271)

• IETF MIB II (RFC-1213)

• IETF Bridge MIB (RFC-1493)

and a host of other Cabletron Enterprise MIBs.

INB

The 9E312-12 attaches to INB1 of the MMAC-Plus Backplane. The INB has a

capacity of 2 Gbps to interconnect MMAC-Plus modules supporting Ethernet,

FDDI, Token Ring, WAN and ATM networks. The INB transports ﬁxed length

data blocks between modules in the MMAC-Plus hub using a Time Division

Multiplexing (TDM) design. Within the INB there is a 64 bit wide data bus and an

eight bit control management bus. Each module that attaches to the INB has an

INB Network Interface Block (NIB). The INB NIB converts canonical frames to

ﬁxed length data blocks for transmission onto the INB. For data blocks received

from the INB, the INB NIB reassembles the data blocks received from the INB

back into canonical frames for transmission to the Fast Packet Switch (FPS) and

ultimately to the front panel port. The INB can time slice its bandwidth using one

of three methods. The default method is standard TDM round-robin bandwidth

arbitration, the second method is for modules to reserve a speciﬁc amount of

bandwidth using MONARCH, Cabletron’s INB Bandwidth Arbitrator, the third

method permits the lowest slot number to use any bandwidth not used by the

previous two methods.

LANVIEW LEDs

The 9E312-12 uses LANVIEW – the Cabletron Systems built-in visual diagnostic

and status monitoring system. With LANVIEW LEDs, you can quickly identify, at

a glance, system status as well as the device, port, and physical layer status. Two

LEDs indicate the transmission and reception of data from the INB MMAC-Plus

Backplane connection. Each of the 12 Ethernet front panel ports features two

LEDs per port to indicate the ports Administrative status (enabled/disabled),

LINK status (Link/Nolink), and Data Activity (receiving and transmitting data).

For a complete list of supported MIBs, refer to the release notes provided in the

9E312-12 package.

NOTE

Introduction

1-4

Figure 1-1. The 9E312-12 Module

INB

9E312-12

ETHERNET

SMB

CPU

MMAC PLUS MMAC PLUS

Autres manuels pour MMAC-Plus 9E312-12

Table des matières

Autres manuels Cabletron Systems Changer

Cabletron Systems

Cabletron Systems SMALL OFFICE CyberSwitch 150 Manuel utilisateur

Cabletron Systems

Cabletron Systems pmn Manuel utilisateur

Cabletron Systems

Cabletron Systems CyberSWITCH CSX150 Manuel utilisateur

Cabletron Systems

Cabletron Systems DLEHF-MA Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartSwitch 9000 Manuel utilisateur

Cabletron Systems

Cabletron Systems IA1100 Instructions de montage

Cabletron Systems

Cabletron Systems MMAC-Plus 9H421-12 Manuel

Cabletron Systems

Cabletron Systems SmartSTACK EPIM1000-S1LX 1000BASE-LX Manuel utilisateur

Cabletron Systems

Cabletron Systems 7F06-02 FDDI SmartSwitch Manuel utilisateur

Cabletron Systems

Cabletron Systems CyberSWITCH CSX1000 Manuel utilisateur

Cabletron Systems

Cabletron Systems 9F426-02 Manuel utilisateur

Cabletron Systems

Cabletron Systems 24 Manuel utilisateur

Cabletron Systems

Cabletron Systems 2H23-50R Manuel utilisateur

Cabletron Systems

Cabletron Systems FN100 Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartSwitch 9W006 Manuel utilisateur

Cabletron Systems

Cabletron Systems FRM Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartSwitch 04-0053-01 Manuel utilisateur

Cabletron Systems

Cabletron Systems MRXI 10BASE-T Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartCell ZX-250 Manuel utilisateur

Cabletron Systems

Cabletron Systems ESXMIM Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartSwitch 9000 Document technique

Cabletron Systems

Cabletron Systems MicroMMAC-24E Manuel utilisateur

Cabletron Systems

Cabletron Systems FN10 Manuel utilisateur

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Instructions de montage

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur