BWI Eagle AIR-EAGLE SR PLUS Manuel utilisateur

AIR-EAGLE SR PLUS

36-HH-4

2.4 GHz RF Transmitter

Document Date: 6/21/2021

Product Rev: 12

36-HH-4

WARRANTY STATEMENT

BWI Eagle Inc. warrants the Air-Eagle Remote Control System, if properly used and installed, will be free

from defects in material and workmanship for a period of 1 year after date of purchase. Said warranty to

include the repair or replacement of defective equipment. This warranty does not cover damage due to

external causes, including accident, problems with electrical power, usage not in accordance with product

instructions, misuse, neglect, alteration, repair, improper installation, or improper testing. This limited

warranty, and any implied warranties that may exist under state law, apply only to the original purchaser of

the equipment, and last only for as long as such purchaser continues to own the equipment. This warranty

replaces all other warranties, express or implied including, but not limited to, the implied warranties or

merchantability and fitness for a particular purpose. BWI Eagle makes no express warranties beyond

those stated here. BWI disclaims without limitation, implied warranties of merchantability and fitness for a

particular purpose. Some jurisdictions do not allow the exclusion of implied warranties so this limitation

may not apply to you. To obtain warranty service, contact BWI Eagle for a return material authorization.

When returning equipment to BWI Eagle, the customer assumes the risk of damage or loss during

shipping and is responsible for the shipping costs incurred.

SIGNAL RANGE

Max range statements are estimates based on a clear line of sight with few interferences. Actual range will

vary based on transmitting power, orientation of transmitter and receiver, height of transmitting and

receiving antennas, weather conditions, electronic interference, terrain, and physical obstacles, including

but not limited to; walls, building structures, trees (foliage), metal objects, and landscape (hills, mountains).

WIRELESS STOP SYSTEMS WORK IN CONJUCTION WITH

HARD-WIRED SYSTEMS.

Wireless Stop and E-Stop devices must work in conjunction with a hard-wired

system. A wireless system should never be considered a primary life-saving device.

At least one hard-wired switch must be available in the event the wireless signal is

lost. Failure to comply may result in serious injury or death to personnel and

damage to equipment.

36-HH-4

Dimensions –4.25” L x 2.68” W x .91” D

(note: belt clip adds .43” to depth)

INTRODUCTION

The Air-Eagle SR PLUS TX is a handheld R.F. transmitter capable of sending up to four unique digital

commands to an Air-Eagle SR Receiver located up to 600 feet away. Any number of transmitters and

receivers can be combined to create a medium-range radio frequency system that operates hazardous or

hard-to-reach equipment from safe, convenient locations. Eight user-programmable frequencies allow

multiple systems to operate simultaneously in the same area without interference. This transmitter will

automatically go into “sleep” mode when no buttons are being depressed on the unit to dramatically

extend battery life.

INITIAL OPERATION SET-UP

This transmitter comes factory set to frequency 1 and power level 4 (max range of 600 feet). If you wish to

change the default settings, follow the instructions for FREQUENCY PROGRAMMING AND POWER

LEVEL PROGRAMMING.

CONTROLS & INDICATORS

TX LED

LED illuminates “RED” continuously while button is depressed and unit is

transmitting. When this LED blinks briefly following a transmission, the

battery needs to be replaced. See Note #1

Note #1 –The low battery notification signals have been improved to provide more noticeable

indications and to safely disable communications BEFORE a low battery condition can corrupt internal

memory causing device failure. When a low battery is first detected, the TX LED will blink several times

after all buttons are released. If it is possible to replace the batteries now, please do so. If not, the

operator has approximately 15 more button activations. During this time, when a button is depressed

and held, the TX LED will blink SLOWLY. The slow blinking will continue several more times after all

buttons are released. Transmissions are still being sent to the receiver during this time. When a button

is depressed and the TX LED is RAPIDLY blinking, the RF output is disabled and NO signal will reach

the receiver. The batteries MUST NOW BE REPLACED to resume normal functions.

Pushbuttons 1 thru 4

Transmits individual button RF codes to the receiver

36-HH-4

FREQUENCY PROGRAMMING

Please read through these instructions completely before beginning programming procedure!

At any time, you can check the current frequency setting by depressing Buttons 3 & 4 simultaneously, for

approximately 5 seconds, until the TX LED is illuminated RED. Then release the buttons and watch as

the TX LED stays RED for about 8 seconds, goes out, then begins to blink. The TX LED will blink RED

one, two, three or four times for Frequencies 1 thru 4, or will blink GREEN one, two, three or four times

for Frequencies 5 thru 8 accordingly. See table below for clarification.

LED Flashes:

Indicates Unit is Operating On:

RED –one time

Frequency 1

RED –two times

Frequency 2

RED –three times

Frequency 3

RED –four times

Frequency 4

GREEN –one time

Frequency 5

GREEN –two times

Frequency 6

GREEN –three times

Frequency 7

GREEN –four times

Frequency 8

To change the setting, follow these steps:

To select from Frequencies 1 thru 4:

1. Depress Buttons 3 & 4 simultaneously until the TX LED is illuminated RED. (Approximately 5

seconds)

2. Release Buttons 3 & 4, then while the TX LED is still illuminated RED, depress Button 1 to select

“Frequency 1” or Button 2 to select “Frequency 2” etc. If the transmit LED goes out before you

have selected a network, no settings will have changed, and the LED will blink corresponding to

the frequency that the TX is currently set to. You must then begin again at step 1 if you wish to

change the current setting.

3. The TX LED will blink to confirm that your frequency selection has been accepted, and then will

go out. For instance, if you have selected Frequency 1, the TX LED will blink RED once to

confirm. If you have selected Frequency 4, the TX LED blinks RED four times to confirm.

To select from Frequencies 5 thru 8:

1. Depress Buttons 3 & 4 simultaneously until the TX LED is illuminated GREEN. (Approximately 8

seconds)

2. Release Buttons 3 & 4, then while the TX LED is still illuminated GREEN, depress Button 1 to

select “Frequency 5” or Button 2 to select “Frequency 6” etc. If the transmit LED goes out before

you have selected a network, no settings will have changed, and the LED will blink corresponding

to the frequency that the TX is currently set to. You must then begin again at step 1 if you wish to

change the current setting.

3. The TX LED will blink to confirm that your frequency selection has been accepted, and then will

go out. For instance, if you have selected Frequency 5, the TX LED will blink GREEN once to

confirm. If you have selected Frequency 6, the TX LED blinks GREEN two times to confirm.

Programming is now complete, and the transmitter is active for normal operation.

You may repeat the above procedure if you wish to change the frequency at any time.

36-HH-4

POWER LEVEL PROGRAMMING

Please read through these instructions completely before beginning programming procedure!

All transmitters are set to Power Level 4 (max range 600 ft) default. The power level can be changed at

any time by following the procedure below. Power level settings will not be changed during normal battery

replacement.

At any time, you can check the current power level by depressing Buttons 3 & 4 simultaneously, for

approximately 11 seconds, until the TX LED starts blinking GREEN. Then release the buttons and watch

as the TX continues to blink for 10 seconds, goes out, then begins to blink again. The TX LED will blink

GREEN one, two, three or four times corresponding the power level setting (see table below)

LED Flashes:

Indicates Unit is Set To:

GREEN –one time

Power Level 1 –Approx 100 Ft Range

GREEN –two times

Power Level 2 –Approx 250 Ft Range

GREEN –three times

Power Level 3 –Approx 400 Ft Range

GREEN –four times

Power Level 4 –Approx 600 Ft Range

To change the setting, follow these steps:

To select a power level:

1. Depress Buttons 3 & 4 simultaneously until the TX LED is blinking GREEN (Approximately 11

seconds)

2. Release Buttons 3 & 4, then while the TX LED is still blinking GREEN, depress Button 1 to select

“Power Level 1” or Button 2 to select “Power Level 2” etc. If the transmit LED goes out before you

have selected a power level, no settings will have changed, and the LED will blink corresponding

to the power level the TX is currently set to. You must then begin again at step 1 if you wish to

change the current setting.

3. The TX LED will blink to confirm that your power level selection has been accepted, and then will

go out. For instance, if you have selected Power Level 1, the TX LED will blink GREEN once to

confirm. If you have selected Power Level 3, the TX LED blinks GREEN three times to confirm.

APPROVALS

United States (FCC)

MCQ-XBEE3

Canada (IC)

1846A-XBEE3

Europe (CE)

ETSI

Australia

RCM

Brazil

ANATEL 06329-18-01209

36-HH-4

SPECIFICATIONS

Keypad

Durable Sealed Membrane Keypad –Eliminates Dust, Dirt and

Moisture Failures

Enclosure

ABS UL94 HB

Enclosure with ring is rated IP54 *Not

Waterproof

Protective Ring

SEBS (TPE)

Power Requirements

3.0 VDC

Battery Type

(2) 1.5V lithium each, size AAA, to equal 3.0VDC nominal.

***For best performance use ONLY Energizer Brand Lithium

Batteries

*Note: Current frequency settings are maintained in flash memory during battery

replacement. No reprogramming of frequency settings is necessary!

Battery Life(Active Usage)

Up to 6 months

Battery Life(Sleep Mode)

Up to 1 Year

Transmit Frequency

2.4GHz Spread Spectrum

RF Networks

Eight Independent Frequencies

RF Output Power

User Selectable from 1mW - 60 mW

Max Transmit Range

User-Selectable from 100 - 600 Feet

Note: Range figures are estimates, based on free-air terrain with limited sources of interference. Actual range will vary

based on transmitting power, orientation of transmitter and receiver, height of transmitting antenna, height of receiving

antenna, weather conditions, interference sources in the area, and terrain between receiver and transmitter, including, but

not limited to, indoor and outdoor structures such as walls, metal objects, trees, buildings, hills, and mountains.

Operating Temperature

-40oF to +185oF

Weight

Approx .22 lbs. (w/belt clip)

Autres manuels pour AIR-EAGLE SR PLUS

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels BWI Eagle Émetteur

BWI Eagle

BWI Eagle AIR-EAGLE SR PLUS 36-HH-4-VBR Manuel

BWI Eagle

BWI Eagle AIR-EAGLE XLT Manuel

BWI Eagle

BWI Eagle AIR-EAGLE SR PLUS 36-1800-120VAC Manuel

BWI Eagle

BWI Eagle AIR-EAGLE FM2 43-1000-RB-N4-120VAC Manuel

BWI Eagle

BWI Eagle AIR-EAGLE FM2 43-1000-120VAC Manuel

BWI Eagle

BWI Eagle AIR-EAGLE SR PLUS TX Manuel

BWI Eagle

BWI Eagle AIR-EAGLE XLT Manuel

BWI Eagle

BWI Eagle AIR-EAGLE SR PLUS Manuel

BWI Eagle

BWI Eagle AIR-EAGLE FM2 43-1000N4W-120VAC Manuel

BWI Eagle

BWI Eagle AIR-EAGLE XLT Manuel

BWI Eagle

BWI Eagle AIR-EAGLE SR PLUS Manuel utilisateur

BWI Eagle

BWI Eagle AIR-EAGLE SR PLUS 36-1420-2B-120VAC Manuel

BWI Eagle

BWI Eagle AIR-EAGLE XLT PLUS 465UEBD-HH Manuel

BWI Eagle

BWI Eagle AIR-EAGLE XLT Manuel

BWI Eagle

BWI Eagle AIR-EAGLE XLT 441-HH-1 Manuel utilisateur

BWI Eagle

BWI Eagle AIR-EAGLE XLT Manuel

BWI Eagle

BWI Eagle AIR-EAGLE XLT Manuel

BWI Eagle

BWI Eagle AIR-EAGLE XLT PLUS Manuel utilisateur

BWI Eagle

BWI Eagle AIR-EAGLE XLT Manuel utilisateur

BWI Eagle

BWI Eagle AIR-EAGLE FM2 43-1100 Manuel

BWI Eagle

BWI Eagle AIR-EAGLE XLT 441P-HH-4-002-CL Manuel

BWI Eagle

BWI Eagle AIR-EAGLE FM2 43-1000-DC Manuel

BWI Eagle

BWI Eagle AIR-EAGLE XLT Manuel

BWI Eagle

BWI Eagle 461-1200-DC Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur