Bosch ISW-BHB1-WX Manuel de service

TECHNICAL BULLETIN

Intrusion wLSN Wireless Devices

Signal-to-Noise Ratio Values March 4, 2010

Issue Severity: Products Affected:

High: Act immediately

Medium: Bosch Security Systems, Inc.

strongly recommends you take the action(s)

described below.

Low: Advisory

•wLSN Hub (ISW-BHB1-WX)

•wLSN Installation Tool

(ISW-BIT1-HAX, -HBX, -HCX)

•Compatible wLSN Devices

1.0 Issue

The Signal-to-Noise Ratio (SNR) recommendations that are shown in the wLSN Reference Guide

(P/N: F01U009440) do not adequately ensure a trouble-free wireless installation in certain European markets

where multi-path signal fading might be present. Table 1 shows the SNR values that are currently published in

the reference guide.

Table 1: SNR Values using wLSN Hub (ISW-BHB1-WX)

Signal-to-Noise Ratio Signal Strength

<9 dB Unacceptable

9 dB Marginal (not recommended)

13 dB Acceptable

16 dB Good

20 dB Very good

22 dB Excellent

When the SNR values shown in Table 1 are used to measure signal strength, signal strength can fluctuate

significantly in locations where multi-path signal fading is present. As a result, the device might not be able to

communicate with the hub. If a communication failure occurs and is not resolved within the defined supervision

window, the control panel sends a missing device report to the central monitoring station.

130 Perinton Parkway, Fairport, NY 14450 USA

www.boschsecurity.com

TBI 07-31-09_wLSN_SRN-02

Technical Bulletin

3/201

wLSN Wireless Device

Page 2 of

2.0 Resolution

For more accurate measurements, use the SNR values as shown in Table 2 when performing an RFSS test.

Use the wLSN Installation Tool only in Mode 3. Do not use the Installation Tool in Modes 1 or 2,

and do not use the individual wLSN devices to determine an acceptable SNR. The SNR

measurements in Modes 1 and 2 and directly from the devices do not correspond to the

recommended values indicated in Table 2.

Table 2: Revised SNR Values using wLSN Hub (ISW-BHB1-WX)

Signal-to-Noise Ratio Signal Strength

<30 dB Unacceptable

30 dB Marginal (not recommended)

35 dB Acceptable

40 dB Good

45 dB Very good

50 dB Excellent

To ensure that wLSN devices are operating at acceptable SNR values:

1. Connect to the control panel using a telephone.

Refer to the control panel documentation for connection options.

2. When prompted, enter the installer passcode.

3. Press [1] to enter the System Maintenance Menu, and then press [6] to enter the Wireless Configuration

Menu.

4. From the Wireless Configuration Menu, press [7]. When the control panel announces “Enter the number of

the programming item,” press [2] for signal strength.

5. When the control panel asks for a point number, press [0][1] to [3][2] for Points 1-32, or [3][5] to [3][8] for

Outputs 5-8.

6. After a point or output number is entered, the hub communicates with the selected device to retrieve the

signal strength. The control panel announces the signal strength as two alphanumeric characters. For

example, “3 5.” Refer to Table 3 to cross reference the spoken value to an SNR value.

Table 3: SNR Values from the Control Panel

Control Panel Value SNR Signal Strength

01 - 09 2 dB – 14 dB

0A – 0F 15 dB – 23 dB

10 – 13 24 dB – 29 dB

Unacceptable

14 – 16 30 dB – 33 dB Marginal

17 – 1A 35 dB – 39 dB Acceptable

1B – 1D 41 dB – 44 dB Good

1E – 20 45 dB – 48 dB Very good

21 – 32 50 dB – 75 dB Excellent

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Bosch Système de sécurité

Bosch

Bosch MIC IP starlight 7000i Manuel utilisateur

Bosch

Bosch FMC-300RW-GSRRD Manuel utilisateur

Bosch

Bosch LTC 8016/90 Manuel utilisateur

Bosch

Bosch LTC 1311/20 FlexiDome I Feuille d'instructions

Bosch

Bosch PR109B Manuel utilisateur

Bosch

Bosch Dinion LTC 0385 Manuel utilisateur

Bosch

Bosch HSG9483 Series Manuel utilisateur

Bosch

Bosch DIVAR IP 3000 Manuel utilisateur

Bosch

Bosch SE3000 Series Manuel du produit

Bosch

Bosch APC-AMC2-4W Manuel utilisateur

Bosch

Bosch DIVAR DIP-6080-00N Manuel utilisateur

Bosch

Bosch FRP-OW3000 Manuel utilisateur

Bosch

Bosch D9412GV4 Manuel utilisateur

Bosch

Bosch DS938Z Manuel utilisateur

Bosch

Bosch DIVAR IP all-in-one 7000 3U Manuel utilisateur

Bosch

Bosch ICP-AMAX4-P2-EN Manuel utilisateur

Bosch

Bosch SM120RW Manuel utilisateur

Bosch

Bosch DS484Q Manuel utilisateur

Bosch

Bosch DB-CO Manuel utilisateur

Bosch

Bosch DB18C3100R2 Manuel utilisateur

Bosch

Bosch AMAX 2100 Manuel utilisateur

Bosch

Bosch Plena Power Amplifier Mode d’emploi

Bosch

Bosch VSS7915/00T Manuel utilisateur

Bosch

Bosch ISW-BMC1-M82X Comment utiliser

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur