Bosch DIVAR IP 3000 Manuel utilisateur

DIVAR IP 3000

DIP-3040-00N, DIP-3042-2HD, DIP-3042-4HD

en Installation Manual

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

3 DIVAR IP 3000 Table of Contents | en

Table of contents

1 Safety precautions 4

1.1 General safety precautions 4

1.2 Electrical safety precautions 5

1.3 ESD precautions 6

1.4 Operating precautions 6

2 System overview 7

2.1 Chassis features 7

2.2 Chassis components 7

2.2.1 Chassis 7

2.2.2 Backplane 7

2.2.3 Power supply 8

2.3 Device views 8

2.3.1 LED description - front panel 9

2.3.2 LAN port LED description - rear panel 10

3 Chassis setup and maintenance 11

3.1 Removing hard drive trays 11

3.2 Installing a hard drive 11

4 System setup - first steps 12

4.1 Introduction 12

4.2 Setup instruction 12

4.3 Starting the application 12

4.4 Using Bosch VMS Configuration Wizard 13

4.5 Using Bosch VMS Configuration Client 24

4.6 Using Bosch VMS Operator Client 25

5 Recovering the unit 26

6 Additional Documentation and client software 27

Bosch Sicherheitssysteme GmbH Installation Manual 2013.09 | V2 | DOC

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

4 en | Safety precautions DIVAR IP 3000

1.1

Safety precautions

Observe the safety precautions in this chapter.

General safety precautions

Follow these rules to ensure general safety:

– Keep the area around the system clean and free of clutter.

– Place the chassis top cover and any system components that have been removed away

from the system or on a table so that they won't accidentally be stepped on.

– While working on the system, do not wear loose clothing such as neckties and

unbuttoned shirt sleeves, which can come into contact with electrical circuits or be

pulled into a cooling fan.

– Remove any jewelry or metal objects from your body, which are excellent metal

conductors that can create short circuits and harm you if they come into contact with

printed circuit boards or areas where power is present.

Warning!

Interruption of mains supply:

Voltage is applied as soon as the mains plug is inserted into the mains socket.

However, for devices with a mains switch, the device is only ready for operation when the

mains switch (ON/OFF) is in the ON position. When the mains plug is pulled out of the

socket, the supply of power to the device is completely interrupted.

Warning!

Removing the housing:

To avoid electric shock, the housing must only be removed by qualified service personnel.

Before removing the housing, the plug must always be removed from the mains socket and

remain disconnected while the housing is removed. Servicing must only be carried out by

qualified service personnel. The user must not carry out any repairs.

Warning!

Power cable and AC adapter:

When installing the product, use the provided or designated connection cables, power cables

and AC adaptors. Using any other cables and adaptors could cause a malfunction or a fire.

Electrical Appliance and Material Safety Law prohibits the use of UL or CSA-certified cables

(that have UL/CSA shown on the code) for any other electrical devices.

Warning!

Lithium battery:

Batteries that have been inserted wrongly can cause an explosion. Always replace empty

batteries with batteries of the same type or a similar type recommended by the manufacturer.

Handle used batteries carefully. Do not damage the battery in any way. A damaged battery

may release hazardous materials into the environment.

Dispose of empty batteries according to the manufacturer's instructions.

2013.09 | V2 | DOC Installation Manual Bosch Sicherheitssysteme GmbH

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

1.2

5 DIVAR IP 3000 Safety precautions | en

Warning!

Handling of lead solder materials used in this product may expose you to lead, a chemical

known to the State of California to cause birth defects and other reproductive harm.

Notice!

Electrostatically sensitive device:

To avoid electrostatic discharges, the CMOS/MOSFET protection measures must be carried

out correctly.

When handling electrostatically sensitive printed circuits, grounded anti-static wrist bands

must be worn and the ESD safety precautions observed.

Notice!

Installation should only be carried out by qualified customer service personnel in accordance

with the applicable electrical regulations.

Disposal

Your Bosch product has been developed and manufactured using high-

quality materials and components that can be reused.

This symbol means that electronic and electrical devices that have reached

the end of their working life must be disposed of separately from

household waste.

In the EU, separate collecting systems are already in place for used

electrical and electronic products. Please dispose of these devices at your

local communal waste collection point or at a recycling center.

Electrical safety precautions

Basic electrical safety precautions should be followed to protect you from harm and the

system from damage:

– Be aware of the locations of the power on/off switch on the chassis as well as the room's

emergency power-off switch, disconnection switch or electrical outlet. If an electrical

accident occurs, you can then quickly remove power from the system.

– Do not work alone when working with high voltage components.

– Power should always be disconnected from the system when removing or installing main

system components, such as the motherboard or memory modules. When disconnecting

power, you should first turn off the system and then unplug the power cords from all the

power supply modules in the system.

– When working around exposed electrical circuits, another person who is familiar with the

power-off controls should be nearby to switch off the power if necessary.

– Use only one hand when working with powered-on electrical equipment. This is to avoid

making a complete circuit, which will cause electrical shock. Use extreme caution when

using metal tools, which can easily damage any electrical components or circuit boards

they come into contact with.

– The power supply power cords must include a grounding plug and must be plugged into

grounded electrical outlets. The unit has more than one power supply cord. Disconnect

both power supply cords before servicing to avoid electrical shock.

Bosch Sicherheitssysteme GmbH Installation Manual 2013.09 | V2 | DOC

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

6 en | Safety precautions DIVAR IP 3000

– Mainboard replaceable soldered-in fuses: Self-resetting PTC (Positive Temperature

Coefficient) fuses on the mainboard must be replaced by trained service technicians only.

The new fuse must be the same or equivalent as the one replaced. Contact technical

support for details and support.

Caution!

Mainboard Battery: There is a danger of explosion if the onboard battery is installed upside

down, which will reverse its polarities. This battery must be replaced only with the same or

an equivalent type recommended by the manufacturer (CR2032). Dispose of used batteries

according to the manufacturer's instructions.

1.3 ESD precautions

Electrostatic Discharge (ESD) is generated by two objects with different electrical charges

coming into contact with each other. An electrical discharge is created to neutralize this

difference, which can damage electronic components and printed circuit boards. The

following measures are generally sufficient to neutralize this difference before contact is made

to protect your equipment from ESD:

– Do not use mats designed to decrease electrostatic discharge as protection from

electrical shock. Instead, use rubber mats that have been specifically designed as

electrical insulators.

– Use a grounded wrist strap designed to prevent static discharge.

– Keep all components and printed circuit boards (PCBs) in their antistatic bags until ready

for use.

– Touch a grounded metal object before removing the board from the antistatic bag.

– Do not let components or printed circuit boards come into contact with your clothing,

which may retain a charge even if you are wearing a wrist strap.

– Handle a board by its edges only. Do not touch its components, peripheral chips, memory

modules or contacts.

– When handling chips or modules, avoid touching their pins.

– Put the mainboard and peripherals back into their antistatic bags when not in use.

– For grounding purposes, make sure your computer chassis provides excellent

conductivity between the power supply, the case, the mounting fasteners and the

mainboard.

1.4 Operating precautions

The chassis cover must be in place when the system is operating to assure proper cooling. Out

of warranty damage to the system can occur if this practice is not strictly followed.

Note:

Please handle used batteries carefully. Do not damage the battery in any way. A damaged

battery may release hazardous materials into the environment. Do not discard a used battery

in the garbage or a public landfill. Please comply with the regulations set up by your local

hazardous waste management agency to dispose of your used battery properly.

2013.09 | V2 | DOC Installation Manual Bosch Sicherheitssysteme GmbH

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

7 DIVAR IP 3000

2.1

2.2

2.2.1

2.2.2

System overview | en

System overview

The DIVAR IP 3000 system is an affordable and easy to use all-in-one recording, viewing, and

management solution for network surveillance systems of up to 32 channels. All channels are

pre-licensed. Running the full Bosch VMS solution and powered by Bosch VRM (Video

Recording Manager) including the Video Streaming Gateway to integrate 3rd party cameras,

DIVAR IP 3000 is an intelligent IP storage device that eliminates the need for separate NVR

(Network Video Recorder) server and storage hardware.

DIVAR IP 3000 is a 4-bay mini tower unit that combines advanced management and state-of-

the-art recording management into a single cost-effective, plug and play IP recording appliance

for IT-minded customers which are seeking for a state-of-the-art “second generation” DVR and

NVR recording solution.

Easy to install and operate, DIVAR IP 3000 features wizard-based set-up and centralized

configuration to reduce installation times. All components are pre-installed and pre-

configured. Simply connect to the network and turn on the unit — DIVAR IP 3000 is ready to

begin recording straight out of the box.

Bosch Video Management System manages all IP and digital video and audio, plus all the

security data being transmitted across your IP network. It seamlessly combines IP cameras

and encoders, provides system-wide event and alarm management, system health monitoring,

user and priority management.

DIVAR IP 3000 features front-swappable SATA-II hard drives providing up to 8 TB of gross

storage capacity. All system software is pre-installed and pre-activated — creating an out-of-

the-box ready-to-use video management appliance. DIVAR IP 3000 utilizes Windows Storage

Server 2008 R2 operating system.

Chassis features

The chassis includes the following features:

– CPU (Intel i3 processor)

– 4 slots for SATA drives (front replaceable)

– 1x VGA output (onboard)

– 1x DVI graphics output

– 4x USB 2.0, 1x USB 3.0

– 1x internal USB Transcoder device

– 1x Gigabit Ethernet LAN port

Chassis components

This chapter describes the most common components included with your chassis.

Chassis

The chassis includes 4 slots for hard drives.

Backplane

The backplane accepts front-swappable SATA-II hard drives providing up to 8 TB of gross

storage capacity.

Warning!

Use caution when servicing and working around the backplane. Hazardous voltage or energy

is present on the backplane when the system is operating. Do not touch the backplane with

any metal objects and make sure no ribbon cables touch the backplane.

Installation Manual 2013.09 | V2 | DOC

Bosch Sicherheitssysteme GmbH

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

8 en | System overview DIVAR IP 3000

2.2.3

2.3

Power supply

The chassis features a highly energy-efficient power supplies.

Device views

There are several LEDs on the front and rear of the chassis. The LEDs show the over-all status

of the system and the activity and health of specific components.

Front view:

52 3 4

1 Lock for front cover 4 LAN activity LED

2 Power on/off LED 5 System status LED

3 Hard disk access LED 6 Individual hard disk LED

2013.09 | V2 | DOC Installation Manual Bosch Sicherheitssysteme GmbH

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

9 DIVAR IP 3000 System overview | en

Rear view:

2 3 4 5 7

1 1x VGA (monitor) 5 Mains connection 100 - 240 VAC

2 1x Ethernet (RJ45) 6 1x USB 3.0

Note: Do not use this port for

keyboard and mouse.

3 4x USB 2.0

Note: Use these ports for keyboard

and mouse connection.

7 1x DVI (monitor), for local viewing

Note:

If the system is only connected to the

DVI port, no video signal is displayed

until the system has started

completely. This can take 1 – 2

minutes. A video signal is always

displayed when the monitor is

connected to the VGA port.

4 1x eSATA for data export

Note: Do not connect hard disk drives

for recording.

LED description - front panel

This chapter describes the LED displays on the front of the chassis.

LED indicator LED color LED state Description

Power LED N/A Off Power off

Blue On (default) Working (S0 state)

Bosch Sicherheitssysteme GmbH Installation Manual 2013.09 | V2 | DOC

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

2.3.1

2.3.2

10 en | System overview DIVAR IP 3000

LED indicator LED color LED state Description

HDD LED N/A Off No disk access

Blue Blinking Disk access

LAN LED N/A Off Network disconnected

Blue On Network connected

Blue Blinking Network activity

System LED N/A Off Power off

Blue On (default) System has booted in normal operation.

Blue Blinking System is booting or shutting down

Red On Critical event occurred, such as degraded

RAID volume.

Bosch also provides the API and then

application program is able to control this

status.

Individual hard

disk LED

N/A Off (default) Hard drive not present.

Blue On Hard drive present.

Red On Bosch provides the API to let application

program to control this status.

LAN port LED description - rear panel

This chapter describes the LAN port LED on the rear of the chassis.

LAN connector:

Nr. LED indicator LED color LED state NIC state

1 RJ45 LED

(left)

N/A

Green

Off

No connection or 10 Mb/s

100 Mb/s

Yellow On 1000 Mb/s

2 RJ45 LED

(right)

Yellow

Blinking

Active connection

Transmit or receive activity

2013.09 | V2 | DOC Installation Manual Bosch Sicherheitssysteme GmbH

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Bosch Système de sécurité

Bosch

Bosch Dinion LTC 0385 Manuel utilisateur

Bosch

Bosch LTC 8016/90 Manuel utilisateur

Bosch

Bosch Solution 16i Manuel utilisateur

Bosch

Bosch Radion Specialty RFBT Manuel utilisateur

Bosch

Bosch FMC-300RW-GSGRD Manuel utilisateur

Bosch

Bosch Security System Manuel utilisateur

Bosch

Bosch DIVAR IP all-in-one 7000 3U Manuel utilisateur

Bosch

Bosch B4512 Manuel utilisateur

Bosch

Bosch UEZ Manuel utilisateur

Bosch

Bosch LTC 2682/90 Series Manuel utilisateur

Bosch

Bosch VSS7902/00T Guide de démarrage rapide

Bosch

Bosch SE 60 LSNi Manuel utilisateur

Bosch

Bosch GVS1000 Manuel utilisateur

Bosch

Bosch FMC-210-SM Manuel utilisateur

Bosch

Bosch Solution 16plus Manuel utilisateur

Bosch

Bosch Solution 16plus Manuel utilisateur

Bosch

Bosch AMAX 2100 Manuel d'instructions

Bosch

Bosch NDA-U-PA0 Manuel utilisateur

Bosch

Bosch TC2073 Manuel utilisateur

Bosch

Bosch LTC 8540/00 Manuel utilisateur

Bosch

Bosch VSS7915/00T Manuel utilisateur

Bosch

Bosch D9412GV4 Manuel utilisateur

Bosch

Bosch MIC IP starlight 7000i Manuel utilisateur

Bosch

Bosch PVA-1EB Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur