Bosch D9412GV4 Manuel utilisateur

D9412GV4/D7412GV4 v2.03

en UL Installation Guide

Table of contents | en 3

Bosch Security Systens, Inc. UL Installation Guide 2016.07 | 04 | F.01U.291.483

Table of contents

1Introduction 5

1.1 About documentation 5

1.2 Bosch Security Systems, Inc. product manufacturing dates 5

2Installation 6

2.1 Installation Preparation 6

2.2 Enclosure Options 6

2.3 Mounting Enclosure 6

2.4 Installing the Control Panel 7

2.5 Connecting Earth Ground 8

2.5.1 Terminal 10 8

2.5.2 Ground Fault Detect Enable 8

2.5.3 Enabling Ground Fault Detection 8

2.5.4 Ground Fault Impedance Specifications 9

2.5.5 Locking the Reset Pin 9

3Diagrams 11

3.1 Faceplates 11

3.2 Power Supply Side Wiring Diagrams 12

3.2.1 D9412GV4/D7412GV4 v2.00 (and higher) Power Supply Side System (D113, D122/

D122L, D192G, D928, D1640, D8132) Wiring Diagram (Power and Phone)

3.2.2 Wiring D125B to G-series control panels 13

3.3 D9412GV4/D7412GV4 v2.00 (and higher) Input Points and Peripheral Devices (D125B,

D129, D130) System Wiring Diagram

3.4 SDI and Zonex Devices Wiring Diagrams 15

3.4.1 D9412GV4 SDI and Zonex Devices (B420/B426, B450, D1255/D1255RB, D1256RB,

D1257RB, D1265, D8125, D8128D, D8129, DX4020, ITS-DX4020-G, D9210C D9127U/T)

System Wiring Diagram

3.4.2 D7412GV4 SDI and Zonex Devices (B420/B426, B450, D1255/D1255RB, D1256RB,

D1257RB, D1265, D8125, D8128D, D8129, DX4020, ITS-DX4020-G, D9210C D9127U/T)

System Wiring Diagram

3.5 D9412GV4/D7412GV4 SDI2 Devices (B208, B308, B420/B426, B450, B520, B810, B820,

B915/B920/B921C/B930/B942/B942W) System Wiring

3.5.1 SDI2 Bus Wiring Recommendations 19

3.6 Keyswitch Wiring 20

4Power Supply and Power Outputs 22

4.1 Power Supply - Primary 22

4.1.1 Primary (AC) Power Circuit 22

4.1.2 Installing the Transformer 22

4.2 Power Terminals - Secondary 23

4.2.1 Secondary (DC) Power 23

4.2.2 Installing the Battery 23

4.3 Power Outputs - Circuit Protection 25

4.4 Power Outputs - Total Available Power 26

4.5 Power Outputs - Continuous Power Output Terminals 3, 8, 24, 32, and 36 26

4.6 Power Outputs - Programmable Power Output Terminals 6, 7, and 8 26

4.6.1 Programming 26

4.6.2 Terminals 6 and 7 27

4.6.3 Fire System Power Formula 27

4.6.4 Terminal 8 27

4en | Table of contents

2016.07 | 04 | F.01U.291.483 UL Installation Guide Bosch Security Systens, Inc.

5Specifications 29

5.1 B520 Specifications 31

5.2 Terminal Wiring Requirements 32

5.3 Compatibilities 34

5.4 Circuit Classes 36

Introduction | en 5

Bosch Security Systens, Inc. UL Installation Guide 2016.07 | 04 | F.01U.291.483

1 Introduction

1.1 About documentation

This document is the intellectual property of Bosch Security Systems, Inc. and is protected by

Trademarks

All hardware and software product names used in this document are likely to be registered

trademarks and must be treated accordingly.

1.2 Bosch Security Systems, Inc. product manufacturing dates

Use the serial number located on the product label and refer to the Bosch Security Systems,

Inc. website at http://www.boschsecurity.com/datecodes/.

The following image shows an example of a product label and highlights where to find the

manufacturing date within the serial number.

6en | Installation

2016.07 | 04 | F.01U.291.483 UL Installation Guide Bosch Security Systens, Inc.

2 Installation

2.1 Installation Preparation

This section contains a general installation procedure and refers to other sections of the

document for detailed instructions. Review this document and the D9412GV4/D7412GV4

Program Entry Guide (P/N: F01U265459) before beginning the installation to determine the

hardware and wiring requirements for the features used. Refer to the documents listed below

for additional information:

–D9412GV4/D7412GV4 v2.03 Installation and System Reference Guide (P/N: F01U265457)

–D9412GV4/D7412GV4 v2.03 Owner’s Manual (P/N: F01U287176)

2.2 Enclosure Options

Mount the control panel assembly in any of the enclosures listed below:

– D8103 Universal Enclosure (tan)

– D8109 Fire Enclosure (red) for the D9412GV4 and D7412GV4 Control Panels

– D8108A Attack Resistant Enclosure (tan)

Refer to the Approved Applications chapter inside the D9412GV4/D7412GV4 v2.03 Installation

and System Reference Guide (P/N: F01U265457) to determine if the application requires a

specific enclosure.

2.3 Mounting Enclosure

1. Run the necessary wiring throughout the premises.

2. Mount the enclosure in the desired location. Use all five enclosure mounting holes. Refer

to the diagram for mounting locations and descriptions.

3. Pull the wires into the enclosure.

Installation | en 7

Bosch Security Systens, Inc. UL Installation Guide 2016.07 | 04 | F.01U.291.483

Notice!

Electromagnetic interference (EMI) can cause problems on long wire runs.

Figure2.1: Enclosure Mounting

Callout - Description

1 - Point chart label

2 - Mounting skirt hooks (2)

3 - Module mounting holes (12)

4 - Tamper switch mounting holes (5)

5 - Skirt mounting hole (1)

6 - Enclosure mounting holes (5)

7 - Mounting skirt hook holes (2)

8 - Back of the control panel

9 - Lock down tab

2.4 Installing the Control Panel

1. Place the control panel over the inside back of the enclosure, aligning the large

rectangular openings of the mounting skirt with the mounting hooks of the enclosure.

Slide the control panel down so that it hangs on the hooks. Refer to Figure 2.1.

2. Remove the tape from the #6 x 1/4-in. screw in the mounting tab on the control panel.

The screw passes through the mounting tab and into the skirt mounting hole in the

enclosure. Tighten the screw to secure the control panel in the enclosure.

3. Connect earth ground to the control panel before making any other connections. Refer to

Connecting Earth Ground.

8en | Installation

2016.07 | 04 | F.01U.291.483 UL Installation Guide Bosch Security Systens, Inc.

2.5 Connecting Earth Ground

2.5.1 Terminal 10

To help prevent damage from electrostatic charges or other transient electrical surges,

connect the system to earth ground at Terminal 10 before making other connections.

Recommended earth ground references are a grounding rod or a cold water pipe.

Warning!

Do not use telephone or electrical ground for the earth ground connection. Use 14 AWG (1.8

mm) to 16 AWG (1.5 mm) wire when making the connection. Do not connect other control

panel terminals to earth ground.

2.5.2 Ground Fault Detect Enable

Notice!

To meet UL 864 requirements, enable Ground Fault Detect.

A ground fault is a circuit impedance to earth ground. The control panel has a ground fault

detection circuit that, when enabled, detects ground faults on Terminals 1 to 9 and 11 to 36.

The control panel also detects and annunciates ground faults on any device connected to it.

If a ground fault condition occurs, the keypads display SERVC GND FAULT and the control

panel sends a GROUND FAULT TROUBLE, AREA 1. When the control panel recognizes that the

ground fault condition is corrected, and remains corrected for between 5 to 45 consecutive

seconds, a Restoral Report is sent.

2.5.3 Enabling Ground Fault Detection

To enable the Ground Fault Detect Enable feature, lock (close) the S4 Ground Fault Detect Pin

on the control panel.

Installation | en 9

Bosch Security Systens, Inc. UL Installation Guide 2016.07 | 04 | F.01U.291.483

Figure2.2: Ground Fault Detect (S4)

Callout - Description

1 - S4 Locked (Closed). Control panels detects ground faults.

2 - S4 Unlocked (Open). Control panel does not detect ground faults.

2.5.4 Ground Fault Impedance Specifications

The table below provides the impedance specifications for detecting ground faults when any

terminal or field wiring is shorted to ground.

Impedance Control Panel Detects Ground Fault

≤ 300 Ω Yes

300 Ω to 200 k Ω Detection depends upon the terminal

≥ 200 k Ω No

Tab.2.1: Ground Fault Impedance Specifications

2.5.5 Locking the Reset Pin

Locking the reset pin disables the control panel. When the reset pin is locked, the control

panel is disabled. CALL FOR SERVICE appears in some keypad displays (SDI2 keypads display

enter Installer Passcode) when the pin is locked down.

On-board outputs (Terminals 6 and 7) and off-board outputs deactivate when the control

panel is disabled. Terminal 8 has power when the output is deactivated. Activation interrupts

power at that terminal. The on-board output (Terminal 8) remains deactivated when the reset

pin is locked in the disable position.

Unlocking the reset pin from the locked position resets the control panel. The control panel

resets all its timers, counters, indexes, and buffers. Any points that restore after a reset do not

generate Restoral Reports.

If the reset pin is placed in the Lock position, and all areas are armed, the control panel will

not answer RPS over a phone line unless the Answer Armed program item has a value other

than zero in it. No entry is required for network or RPS Enhanced direct connection

communication. Refer to RPS Parameters in RPS Help.

10 en | Installation

2016.07 | 04 | F.01U.291.483 UL Installation Guide Bosch Security Systens, Inc.

Figure2.3: Reset Pin

Callout - Description

1 - Reset pin locked (closed)

2 - Reset pin normal (open)

Autres manuels pour D9412GV4

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Bosch Système de sécurité

Bosch

Bosch SOLUTION 6000 Manuel utilisateur

Bosch

Bosch D222 Manuel utilisateur

Bosch

Bosch B926F Manuel utilisateur

Bosch

Bosch DS938Z Manuel utilisateur

Bosch

Bosch MBV-BPRO-45 Feuille d'instructions

Bosch

Bosch CP156B Comment utiliser

Bosch

Bosch ISW-BMC1-S135X Manuel utilisateur

Bosch

Bosch PVA-1EB Manuel utilisateur

Bosch

Bosch Spexor Manuel utilisateur

Bosch

Bosch Praesideo Manuel utilisateur

Bosch

Bosch AMAX panel 4000 Manuel utilisateur

Bosch

Bosch LTC 8850 Series Manuel utilisateur

Bosch

Bosch Solution 2000 Manuel du propriétaire

Bosch

Bosch D2000 Manuel utilisateur

Bosch

Bosch D220 Manuel utilisateur

Bosch

Bosch Plena PLE-1CS Guide de référence

Bosch

Bosch Radion B810 Manuel utilisateur

Bosch

Bosch DB-CO Manuel utilisateur

Bosch

Bosch Solution 16i Manuel utilisateur

Bosch

Bosch CP050B Comment utiliser

Bosch

Bosch IUI-BES-AO Manuel utilisateur

Bosch

Bosch LTC 2682/90 Series Manuel utilisateur

Bosch

Bosch GVS1000 Manuel utilisateur

Bosch

Bosch D623 Series Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur