Bosch D132A Manuel utilisateur

DETECTOR

FIRE PT

AUX PWR

REVERSE

TRIGGER

TRBL PT

D132A

Smoke Detector Reversing Relay Module

D132A

en Installation manual

Smoke Detector Reversing Relay Module Notices | en 3

Bosch Securiity Systems, B.V. Installation manual 2019.08 | 05 | F.01U.069.463

1 Notices

These instructions cover the installation of the D132A Smoke Detector Reversing Relay

Module in a household fire system supervised by a fire alarm control panel (FACP) or a

combination Burglary/Fire control panel.

Before installing the module, become familiar with the Installation and Operation Guide for the

control panel you are using.

Install, test and maintain the module according to these instructions, NFPA 72, local codes,

and the authority having jurisdiction (AHJ). Failure to follow these instructions can result in

failure of a detector to initiate an alarm event. Bosch Security Systems, Inc. is not responsible

for improperly installed, tested or maintained devices.

Warning!

Follow these instructions to avoid personal injury and damage to equipment.

NFPA72 requires that you perform a complete system wide functional test following any

modifications, repair, upgrades or adjustments made to the system’s components, hardware,

wiring, programming and software/firmware.

4en | Description Smoke Detector Reversing Relay Module

2019.08 | 05 | F.01U.069.463 Installation manual Bosch Securiity Systems, B.V.

2 Description

This module allows compatible control panels (see the table below) to sound all smoke

detectors connected to point1 or zone1 when a single smoke detector on the loop goes into

alarm. To restore the smoke detectors to normal, reset the smoke detectors.

The following table lists control panels compatible with the D132A:

Control panels Compatible relays See section:

Active:

B Series panels1 ** D275, PAM-4 Wiring to a B Series panel,

page 8

D6412 and D4412 panels** Wiring to a D6412 or D4412

panel, page 13

G Series (GV2 and higher)

panels2

D275, PAM-4 Wiring to a G Series panel,

page 14

Legacy:

G Series (prior to GV2)

panels3

See control panel’s documentation on the Bosch website

(http://www.boschsecurity.com)

D9412, D7412, D7212**

panels

ICP-EZM2

D2812 panel**

D2412U and D2412UE

panels**

D2212, D2212B, and

D2212BE panels**

DS7240 and DS7220 panels**

1 B Series panels = B6512**, B5512**, B4512**, and B3512**

2 G Series (GV2 and higher) panels = B9512G, B8512G, GV4 (D9412GV4, D7412GV4, and

D7212GV4**), GV3 (D9412GV3, D7412GV3, and D7212GV3**), and GV2 (D9412GV2,

D7412GV2, and D7212GV2**)

3 G Series (prior to GV2) panels = D9412G, D7412G, D7212G**

** indicates products which are not UL listed for commercial fire applications

Smoke Detector Reversing Relay Module Description | en 5

Bosch Securiity Systems, B.V. Installation manual 2019.08 | 05 | F.01U.069.463

Figure2.1: D132A smoke detector reversing relay module

1 Mounting holes 6 Positive (+) power for module

2 Positive (+) to detector 7 Negative (-) power for module

3 Negative (-) to detector 8 Trigger to reverse detector power

Pull to GND to activate

4 Powered loop from control panel or

D125B

9 Positive (+) to trouble point

5 Powered loop from control panel or

D125B

10 Negative (-) to trouble point

6en | Installation Smoke Detector Reversing Relay Module

2019.08 | 05 | F.01U.069.463 Installation manual Bosch Securiity Systems, B.V.

3 Installation

1. Align the module with an available three-hole module mounting location in the enclosure.

2. Fasten the module to the enclosure with the three supplied screws.

For mounting locations inside the enclosure, see the control panel’s Installation Instructions.

Smoke Detector Reversing Relay Module Wiring | en 7

Bosch Securiity Systems, B.V. Installation manual 2019.08 | 05 | F.01U.069.463

4 Wiring

Use the table below to ensure you are using the proper wire gauge for the number of

detectors used and for the length of the detector circuit:

Number of

detectors

Maximum detector circuit length

22AWG

(0.34mm2)

20AWG

(0.5mm2)

18AWG

(0.75mm2)

16AWG

(1.5mm2)

1 935ft (285m) 1490ft (454m) 2370ft (722m) 3770ft (1149m)

2 935ft (285m) 1490ft (454m) 2370ft (722m) 3770ft (1149m)

3 465ft (142m) 745ft (227m) 1185ft (722m) 1885ft (575m)

4 310ft (95m) 495ft (150m) 790ft (241m) 1255ft (383m)

5 230ft (70m) 370ft (113m) 590ft (180m) 940ft (287m)

6 185ft (56m) 295ft (90m) 470ft (143m) 750ft (229m)

7 155ft (47m) 245ft (75m) 395ft (120m) 625ft (191m)

8 130ft (40m) 210ft (64m) 335ft (103m) 535ft (163m)

Notice!

To ensure system supervision, do not use looped wire under the terminals. Break the run to

provide supervision of the connections.

An external 12VDC or 24VDC power supply listed for fire signaling units and commercial or

residential burglary units can be used.

The external power supply must be UL1481 or UL864 Listed, regulated, and power‑limited.

Install the control panel and external power supply in the same room no more than 20ft (6m)

apart. The interconnecting wires between the control panel and external power supply must

be in conduit.

The power source for both the auxiliary power supply and the control panel must be from the

same dedicated AC branch circuit.

8en | Wiring Smoke Detector Reversing Relay Module

2019.08 | 05 | F.01U.069.463 Installation manual Bosch Securiity Systems, B.V.

4.1 Wiring to a B Series panel

4.1.1 Two-wire wiring for 12 VDC supplied by the control panel

Figure4.1: Two-wire wiring of D132A modules to a B Series control panel for power supplied by the panel

1 Detector loop (2‑wire) 9 Connection from D125B switch power

to control panel’s A output relay (NC).

Set the Output A jumper for AUX PWR.

2 EOL resistor 10 Connection for D125B Zone B to an

on-board point on the control panel

3 D132A module 11 Connection for D125B Zone A to an

on‑board point on the control panel

4 Connections for one D132A fire point

to D125B A loop

12 Connection from D125B Common

(either 4 or 5) to the control panel’s

common for the on‑board points

connected

5 Connections for the other D132A fire

point to D125B B loop

13 Earth Ground

6 Connection for AUX PWR - from D132A

modules to B-series panel COM

14 B Series control panel

7 Connection for AUX PWR + from

D132A modules to B-series panel AUX

15 D125B module

8 Connection from reverse trigger on

D132A modules to control panel B or C

output

Pull to GND to activate

Smoke Detector Reversing Relay Module Wiring | en 9

Bosch Securiity Systems, B.V. Installation manual 2019.08 | 05 | F.01U.069.463

Notice!

The illustration shows the D132A modules wired for both detector loops triggered by the

same output. For loops triggered by separate outputs, connect one D132A module reverse

trigger to B output and the other D132A revese trigger to C output.

10 en | Wiring Smoke Detector Reversing Relay Module

2019.08 | 05 | F.01U.069.463 Installation manual Bosch Securiity Systems, B.V.

4.1.2 Four-wire wiring for 12 VDC supplied by the control panel

Figure4.2: Four-wire wiring of D132A modules to a B Series control panel for 12 V power supplied by the panel

1 D132A module 9 D132A Trigger connection to panel’s

Output B or C

Pull to GND to activate

2 Resistor R4: for 4‑wire use, cut the

resistor leads to remove the resistor

10 Positive (+) trouble point connection

to an on‑board point on the control

panel

3 B Series control panel 11 Negative (-) trouble point connection

to an on‑board point on the control

panel

4 End-of-line (EOL) supervisory relay 12 EOL resistors

5 Positive (+) power connection to

detectors

13 Connections between an on‑board

point on the control panel , the

detectors (data lines), and the EOL

Supervision Relay

6 Negative (-) power connection to

detectors

14 First smoke detector on the detector

loop

7 Positive (+) fire point and AUX PWR

connection to panel’s AUX terminal

15 Last smoke detector on the detector

loop

8 Negative (-) fire point and AUX PWR

connection to panel’s COM terminal

Table des matières

Autres manuels Bosch Unité de contrôle

Bosch

Bosch Rexroth M SED 6 VE1 Series Manuel utilisateur

Bosch

Bosch FLM-420/4-CON-S Manuel utilisateur

Bosch

Bosch Heatronic 4000 Instructions d'utilisation

Bosch

Bosch D8128D Manuel utilisateur

Bosch

Bosch B426 Manuel utilisateur

Bosch

Bosch B426 Manuel utilisateur

Bosch

Bosch Rexroth PSI 6500 Series Manuel

Bosch

Bosch Rexroth NYM04.1-5PW-NNNN-NY4125 Manuel utilisateur

Bosch

Bosch DS7400 Manuel utilisateur

Bosch

Bosch rexroth DBD 1X/ E Series Manuel utilisateur

Bosch

Bosch FPE-7039 Manuel utilisateur

Bosch

Bosch Rexroth M-2SMM6 SO711 Series Manuel utilisateur

Bosch

Bosch REXROTH DBD Manuel utilisateur

Bosch

Bosch MU 100 Manuel utilisateur

Bosch

Bosch KTS Truck Manuel utilisateur

Bosch

Bosch MS 50.4 Manuel utilisateur

Bosch

Bosch Rexroth VT-HNC100 3X Series Manuel utilisateur

Bosch

Bosch ETT 223 Manuel utilisateur

Bosch

Bosch CRR 120 Guide de configuration

Bosch

Bosch Rexroth H-4WEH...XE Series Manuel utilisateur

Bosch

Bosch SE352 Manuel utilisateur

Bosch

Bosch Rexroth RE 07601-B Manuel utilisateur

Bosch

Bosch B442 Manuel utilisateur

Bosch

Bosch Rexroth WMM6 Series Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur