Bosch ReadykeyPRO LNL-1200 Manuel utilisateur

LNL-1200 Output Control Module

Quick Reference Guide

For detailed information, please refer to the LNL-1200 tab in the READYKEYPRO Hardware Installation Guide

(49289).

1.0 The Output Control Module Board

The Output Control Module board

contains the following components:

A. sixteen (16) alarm output

relays with

B. sixteen (16) corresponding

status LEDs

C. two (2) unsupervised alarm

inputs

D. one (1) RS-485 interface

E. one (1) power input

F. eight (8) dip switches

G. three (3) jumpers

H. two (2) status LEDs

Figure 1: LNL-1200

LNL-1200

LNL-1200 Quick Reference Guide

2.0 Specifications

The Output Control Module is for use in low voltage, class 2 circuit only.

Primary Power:

DC input 12 VDC @ 850 mA

24 VDC @ 450 mA

Communication Ports Port 1 Port 1: RS-485 (2-wire or 4-wire), 2400 to 38400 bps async

Cabinet Tamper

Monitor unsupervised, dedicated

Inputs

Power Fault

Monitor unsupervised, dedicated

Outputs Sixteen (16) form C dry-contact relays, 5 A @ 28 VDC resistive

Power 1 twisted pair, 18 AWG

RS-485 24 AWG twisted pair(s) with shield, 4000 ft (1200 m)

Inputs twisted pair, 30 ohms maximum

Wire Requirements

Outputs as required for the load

Temperature 0 to 70°C, operating

-55 to +85 °C, storage

Environmental

Humidity 0 to 95% RHNC

Dimension

(HxWxD) 1 in. x 6 in. x 8 in.

(25 mm x 152 mm x 203 mm)

Mechanical

Weight Weight: 16 oz. (454 g) nominal

Table 1: LNL-1100 Specifications

3.0 Installation

3.1 Unsupervised Alarm Inputs: Power Fault and Cabinet Tamper Monitors

Wire the BA (power fault) and CT (cabinet

tamper) inputs using a twisted pair cable, 30

ohms maximum (no EOL resistors required).

If either of these inputs is not used, a jumper

wire should be installed.

3.2 Upstream Controller

Communication to the Intelligent

System Controller

GND

CABINET

TAMPER

POWER

FAULT GND

Figure 2: Unsupervised Alarm Input Wiring

The RS-485 is

asynchronous,

half-duplex, using 1

start bit, 8 data

bits, 1 stop bit.

TR2+

GND

TR3+

TR3-

TR2-

GND

LNL-500

TR+

R+

R-

TR-

GND

Figure 3: RS-485 2-Wire Communications

R-

LNL-500

OUTPUT CONTROL

BOARD

Figure 4: RS-485 4-Wire

Communications

LNL-1200

LNL-1200 Quick Reference Guide

3.3 Power Source Wiring

If Using a 12 VDC Power Source, be sure to observe

polarity. VIN

GND

12 to 24 VDC

Figure 5: Power Source Wiring

3.4 Relay Outputs

DC SOURCE

AC SOURCE

FUSE +

LOAD

MOV

FUSE

Figure 6: Relay Outputs

3.5 Configuration

The LNL Output Control Board contains (8) DIP switches and (3) jumpers that must be configured for your

system.

3.6 Setting DIP Switches DIP Switch(es) Used to configure:

1, 2, 3, 4, 5 Device Communication address (0-31)

6, 7 Communication baud rate

(38400, 19200, 9600 bps)

8 Not used

The default positions for DIP switches is: Address

00; 38,400 bps (switches 6 and 7 are on, others

are off).

12345678

Figure 7: DIP Switch Settings

Table 2: DIP Switch explanations

3.7 Communication Baud Rate DIP SWITCHBaud Rate

(bps) 6 7

38400 ON ON

19200 OFF ON

9600 ON OFF

0 OFF OFF

To configure the communication baud rate, set DIP switches 6 and

7 according to Table 3.

Table 3: Setting Baud Rate

130 Perinton Parkway, Fairport, NY 14450-9199 USA

Customer Service: (800) 289-0096; Technical Support: (888) 886-6189

49307C

Quick Reference Guide 10/06

LNL-1200

Page 4 of 4

3.8 Device Addresses

To configure the device communication address, set DIP switches 1, 2, 3, 4, and 5 according to Table 4.

DIP SWITCH DIP SWITCH

ADDRESS 5: 4: 3: 2: 1: ADDRESS 5: 4: 3: 2: 1:

0 OFF OFF OFF OFF OFF 16 ON OFF OFF OFF OFF

1 OFF OFF OFF OFF ON 17 ON OFF OFF OFF ON

2 OFF OFF OFF ON OFF 18 ON OFF OFF ON OFF

3 OFF OFF OFF ON ON 19 ON OFF OFF ON ON

4 OFF OFF ON OFF OFF 20 ON OFF ON OFF OFF

5 OFF OFF ON OFF ON 21 ON OFF ON OFF ON

6 OFF OFF ON ON OFF 22 ON OFF ON ON OFF

7 OFF OFF ON ON ON 23 ON OFF ON ON ON

8 OFF ON OFF OFF OFF 24 ON ON OFF OFF OFF

9 OFF ON OFF OFF ON 25 ON ON OFF OFF ON

10 OFF ON OFF ON OFF 26 ON ON OFF ON OFF

11 OFF ON OFF ON ON 27 ON ON OFF ON ON

12 OFF ON ON OFF OFF 28 ON ON ON OFF OFF

13 OFF ON ON OFF ON 29 ON ON ON OFF ON

14 OFF ON ON ON OFF 30 ON ON ON ON OFF

15 OFF ON ON ON ON 31 ON ON ON ON ON

Table 4: DIP Switch Device Addresses

2-Wire

4-Wire

3.9 Installing Jumpers

3.9.1 RS-485 Type

Jumper J3 is used to configure the RS-485 type for Port 1 on the

READYKEYPRO Output Control Board. There are two possible

configuration options that can be used to install this jumper: 2-wire

configuration, and 4-wire configuration.

Figure 8: RS-485

configuration for Jumper J3

“ON” Configuration for J1, J2 “Not ON” Configuration for J1, J2

3.9.2 RS-485 EOL

Terminator

Status

Figure 9: Jumper J5 & J6 Configuration

Autres manuels Bosch Unité de contrôle

Bosch

Bosch API-AMC2-4WE Manuel utilisateur

Bosch

Bosch rexroth M1-16 Series Manuel utilisateur

Bosch

Bosch Rexroth R-IB IL 24 PSDO 8-PAC Manuel utilisateur

Bosch

Bosch MM100 Manuel utilisateur

Bosch

Bosch Heatronic 4000 Instructions d'utilisation

Bosch

Bosch B426 Manuel utilisateur

Bosch

Bosch B426 Mode d'emploi

Bosch

Bosch RC 1001 Manuel utilisateur

Bosch

Bosch VCU MS 50.4P Manuel utilisateur

Bosch

Bosch RTM 430 Guide de configuration

Bosch

Bosch PowerBox PBX 190 Manuel utilisateur

Bosch

Bosch Rexroth 4WS2EM 10 Series Manuel utilisateur

Bosch

Bosch Rexroth IndraControl VCP 05.2 Manuel technique

Bosch

Bosch Rexroth NYCe 4000 Manuel utilisateur

Bosch

Bosch Rexroth IndraControl XFE 01.1 Series Manuel utilisateur

Bosch

Bosch rexroth Automax 100 Manuel utilisateur

Bosch

Bosch LSN 0300 A Manuel utilisateur

Bosch

Bosch ConnectModule BCM3100 Manuel utilisateur

Bosch

Bosch B426 Manuel utilisateur

Bosch

Bosch D8125 Mode d'emploi

Bosch

Bosch IOS 0232 A Manuel utilisateur

Bosch

Bosch Professional GCY 42 Manuel utilisateur

Bosch

Bosch Rexroth IndraControl S67 Series Guide de l'utilisateur

Bosch

Bosch Rexroth IMpnio Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur