Bosch CM255B Comment utiliser

CM255B

Factory Default Module

Security System

Installer Reference Guide

Security Systems

CM255B Installer Reference Guide

2Bosch Security Systems 10/12 CM255BIRG FTR1.1

Selected Solution control panels include a software option that when selected will disable the factory defaulting op-

tion. If this option has been set, then you must know the current installer PIN code to access programming mode or

to default the panel. Table 2 lists the current panels which support the CM255B default module.

To determine of the panel has been factory default disabled, remove all power to the panel and then re-apply the

power. If the on board relay pulses or clicks ve times then defaulting has been disabled.

In the eld many situations arise where it is not possible to determine the current installer PIN code. Until now, the

only remedy for this was to remove the control panel and return it to the distributor for factory defaulting. Panel

removal, transportation costs, installer labour and the possibility of damage during transit make this is a costly exer-

cise.

The CM255B factory default module has been designed to eliminate the need to un-wire the control panel or spend

the time and money returning it to the factory for defaulting.

Indicators

The CM255B includes Red and Green indicators which identify the condition of the module.

Module Indicators

Indicator Condition Action

Red LED ON Steady Module has already been used and can’t be used again.

Discard module.

Green LED ON Steady

Default module is good.

Remove power to panel and then re-apply to initiate the defaulting

procedure.

Red & Green LEDs Alternate Flashing Factory defaulting initiated, module can be removed and discarded.

Table 1: Module Indicators

The CM255B is a ONE TIME USE ONLY device. Discard after use!

Testing

If required it is possible to test the state of the CM255B module to see if it has already been used. To do this you

must make sure that the panel is powered up and running BEFORE connecting the CM255B module. Once connect-

ed, if the Green indicator is ON then the module is good and if the Red indicator is ON then the module has been

used and should be discarded.

Operation

Before you are able to use the CM255B you will need to open the control panel cabinet and locate the port on the

circuit board labelled“Serial Port” or “Direct Link Port”.

WARNING all current control panel programming may be be lost if you continue.

Read this sheet completely before proceeding.

1) Remove battery and AC power from the control panel.

2) Plug the CM255B into the connector marked “Serial Port” or “Direct Link Port” paying attention to orientation.

See Figure 1.

3) Apply AC power to the control panel and connect the battery.

4) The red and green indicators on the CM255B should start to ash.

If only the RED indicator comes on then the CM255B has already been used and should be discarded.

5) Once the RED and GREEN indicators are ashing remove the CM255B and discard.

CM255B - Factory Default Module

CM255B Installer Reference Guide

Bosch Security Systems 10/12 CM255BIRG FTR1.1

N12138N12138 RoHS

In the interest of ongoing product development this

document is subject to change without notice.

Compatibility

The CM255B is compatible with the following Solution control panels. For more information please contact your

nearest Bosch branch or Bosch security products distributor.

CM255B Module Compatibility

Panel Type Supported Default Type Performed

Solution 16i Yes Complete Factory Default

Solution 16+ Yes Complete Factory Default

Solution 64 Yes Complete Factory Default

Solution 144 Yes Installer code & RAS Pin Defaulted Only

Table 2: CM255B Module Compatibility

Warranty

There is no warranty provided with this product because of its disposable nature. Once used the module should be

discarded.

CM255B Connection Diagram

GSP

N12138

P/Nº:

MFG:

CC600B

12 Oct 2012

SOLUTION 144

Intrusion Control Panel

VER: 2.00

RoHS



Green LED

Red LED

10 Pin

Serial Port

CM255B Default Module

Connect Here

Control Panel

Figure 1: CM255B Connection Diagram

Bosch Security Systems

25 Huntingwood Drive

Huntingwood, NSW 2148

Australia

Phone: +612 9672 1777

Facsimile: +612 9672 1717

CM255BIRG

Issue FTR1.1

Autres manuels Bosch Unité de contrôle

Bosch

Bosch FLM-420-RLV1-D Guide de dépannage

Bosch

Bosch DS7432 Manuel utilisateur

Bosch

Bosch FLM-420-NAC-D Manuel utilisateur

Bosch

Bosch FLM-420-EOL2W-W Manuel utilisateur

Bosch

Bosch MM100 Manuel de service

Bosch

Bosch B426 Manuel utilisateur

Bosch

Bosch Rexroth IndraControl XM21 Manuel utilisateur

Bosch

Bosch Rexroth NYS04.1-ST-01-LMS-SERCOS-NY4078 Manuel utilisateur

Bosch

Bosch Professional GCY 42 Manuel utilisateur

Bosch

Bosch Rexroth MKK 12-40 Manuel utilisateur

Bosch

Bosch Rexroth R-IB IL 24 PSDO 8-PAC Manuel utilisateur

Bosch

Bosch Rexroth RE 07601-B Manuel utilisateur

Bosch

Bosch Rexroth BVD 52 Series Manuel utilisateur

Bosch

Bosch REXROTH 4WRZ 7X/XE Series Manuel utilisateur

Bosch

Bosch Control 8311 Manuel utilisateur

Bosch

Bosch POPEX B299 Manuel utilisateur

Bosch

Bosch B426 Manuel utilisateur

Bosch

Bosch Rexroth 4WS2EM 10 Series Manuel utilisateur

Bosch

Bosch rexroth 4WS2EM10 5X XH Series Manuel utilisateur

Bosch

Bosch AMC2-4WE Manuel utilisateur

Bosch

Bosch CFB 840 Guide de l'utilisateur

Bosch

Bosch MP 100 Manuel utilisateur

Bosch

Bosch Sensortec Application Board 3.0 Manuel utilisateur

Bosch

Bosch Rexroth VT-HMC 1X Series Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur