Billion BiPAC 7401V(G)PX Manuel utilisateur

BiPAC 7401V(G)PX

3G/ VoIP/ (802.11g) ADSL2+

Firewall Router

Quick Start Guide

Billion BiPAC 7401V(G)PX 3G/ VoIP/ (802.11g) ADSL2+ Firewall Router

PLEASE READ THE QUICK START GUIDE AND FOLLOW THE

STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU

INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE.

IF YOU NEED MORE INFORMATION ON THIS SOFTWARE

CONFIGURATION, PLEASE REFER TO THE USER MANUAL ON

CD-ROM.

Package Contents

3G/ VoIP/ (802.11g) ADSL2+ Firewall Router

CD (containing manual, utility, and QSG)

RJ-11 ADSL/ telephone cable

Ethernet (RJ-45) cable

One 2dBi detachable antenna (Wireless model only)

Power adapter

RJ-45 to RS-232 Console Kit

This Quick Start Guide

Splitter/ Micro-filter (Optional)

zDo not use the router in high humidity or high temperatures.

zDo not use the same power source for the router as other

equipment.

zDo not open or repair the case yourself. If the router is too hot,

turn off the power immediately and have it repaired at a qualified

service center.

zAvoid usin

this

roduct and all accessories outdoors.

Warning

zPlace the router on a stable surface.

zOnly use the power adapter that comes with the package. Using a

different voltage rating power adaptor may damage the router.

Attention

-1-

Quick Start Guide

Hardware Overview

The Front LEDs

The Rear Ports

Connect the

supplied power

adapter to this jack

Connect this port to the

ADSL/telephone network

with the RJ-11 cable

(telephone) provided.

Press it to reset

the device or

restore to factory

default settings

Connect a UTP Ethernet

cable (Cat-5 or Cat-5e) to

one ofthe LAN ports when

connecting to a PC or an

office/home network of

10Mbps or 100Mbps.

Connect the

detachable

antennato this port.

Lit orange red when

power is ON. Lit red

means system is fail.

Lit green when the

system is ready.

Connect this port to

the telephone jack on

the wall with RJ-11

cable.

Lit when connected to an

Ethernet device.

Green for 100Mbps;

Orange for 10Mbps.

Blink when data is

Transmitted / Received.

Lit green when the

hone is of

hook.

Lit Green when the device is

successfully connected to an

ADSL DSLAM. (“line sync”)

Lit green when a

wireless connection is

established. Flash

when the device is

sending/receiving data.

Power

ON/OFF

switch

Lit when the inbound

and outbound calls

are transmitted

through PSTN.

Lit green when the

SIP Registration is

OK.

Push WPS button to

trigger Wi-Fi Protected

Setup function.

Lit red when WAN port fails

to get IP address. Lit green

when WAN port gets IP

address successfully. Lit off

when device in bridged

mode or WAN connection

not present.

Connect this port to

an analog phone set

with RJ-11 cable.

Lit green when the

USB device is ready.

Flashes when

sending/ receiving

data.

3G/ HSDPA USB

modem backup for

Internet access

-2-

Billion BiPAC 7401V(G)PX 3G/ VoIP/ (802.11g) ADSL2+ Firewall Router

-3-

Hardware Connection

Hardware Installation

1. Power Connection

Plug the supplied power adapter into the wall jack and the other side to the router.

Please note that the plug type may differ according to country.

2. LAN Connection

Connect the supplied RJ-45 Ethernet cable to one of the Ethernet ports, and the

other side to the PC’s Ethernet interface.

Quick Start Guide

3. USB Connection

The USB 2.0 port supports 3G/ HSDPA modem connectivity: users can conveniently

access Internet via 3G, eliminating the limitations of the wired network. This solution

also employs an auto fail-over feature to ensure always-on connectivity for SOHO

users.

4. Phone Connection

Connect RJ-11 cable to the router’s phone port and the analog phone set.

5. Line Connection

a) Connect RJ-11 cable to the router Line port and the splitter phone port.

b) Connect RJ-11 cable to the router DSL port and the splitter ADSL port.

c) Connect RJ-11 cable to the splitter Line port and the phone jack on the wall.

-4-

Billion BiPAC 7401V(G)PX 3G/ VoIP/ (802.11g) ADSL2+ Firewall Router

6. EWAN Connection

Connect RJ-45 Ethernet cable to the Ethernet port # 1 (EWAN), and connect the

other side to another alternative broadband device, such as Cable Modem, VDSL,

Fibre Modem or PON optic lines. Please refer to User Manual for detail instruction.

7. Splitter/ Micro-filter Connection

The Splitter / Micro-filters are important for ADSL installation, they help ensure that

high-frequency signals are directed to the ADSL modem, and low-frequency

signals are directed to the telephone or other analog voice-channel device to

prevent inter-modulation distortion and get good speeds and stable ADSL sync

rate.

a) Splitter connection

If the installation has only a single telephone and a single ADSL modem, then a

splitter can be employed.

b) Micro-filter connection

If the installation has several telephones or other analog devices, then an internal

micro-filter can be employed at each analog device.

-5-

Quick Start Guide

Setup Utility

After you complete the hardware installation insert CD into the CD Drive to run the setup utility.

The setup utility will auto-run. Follow the step-by-step configuration wizard & it will guide you to

setting up the basic network configuration.

Connecting to the Router

1. Open the web browser and type http://192.168.1.254 in the browser's address box. This

number is the default IP address for this router. Press Enter.

2. A username and password window will appear. The default username is “admin”, and

password is “admin”. Press OK to proceed.

3. You will get a status report web page and main menu screen.

Please see the relevant sections of user manual for detailed instructions on how to

configure your router.

Troubleshooting

1. None of the LEDs are on when you turn on the router.

Check the connection between the adaptor and the router. If the error persists, you may have

a hardware problem. In this case you should contact technical support.

2. Can’t ping any PCs on the LAN.

Check the Ethernet LEDs on the front panel. The LED should be on for a port that has a PC

connected. If it is off, check the cables between your router and the PC. Make sure you have

uninstalled any software firewall for troubleshooting. Verify that the IP address and the subnet

mask are consistent between the router and the workstations.

3. Frequent loss of ADSL linesync (disconnections).

Ensure that all other devices connected to the same telephone line as your router (e.g.

telephones, fax machines, analogue modems) have a line filter connected between them and

the wall socket (unless you are using a Central Splitter or Central Filter installed by a qualified

and licensed electrician), and ensure that all line filters are correctly installed and the right

way around. Missing line filters or line filters installed the wrong way around can cause

problems with your ADSL connection, including causing frequent disconnections. If you have

a back-to-base alarm system you should contact your security provider for a technician to

make any necessary changes.

Product Support and Contact Information

Most problems can be solved by referring to the Troubleshooting section in the User Manual.If

you cannot resolve the problem with the Troubleshooting chapter, please contact the dealer

where you purchased this product.

Contact Billion

WORLDWIDE

http://www.billion.com

Billion Products Registration

Billion is committed to before and after sales customer services. You will get the most out of your Billion's products

after registration. Please register online at http://www.billion.com/register to receive valuable services and support

from us.

BiPAC 7401V

(

)

PX: V1.00EN

-6-

Autres manuels pour BiPAC 7401V(G)PX

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Billion Routeur réseau

Billion

Billion BiPAC 5200 Manuel utilisateur

Billion

Billion BiPAC 711C2 Manuel utilisateur

Billion

Billion myGuard 7500GL Manuel utilisateur

Billion

Billion BiPAC 7402(G)(L) R3 Series Manuel utilisateur

Billion

Billion BIPAC-7402 Manuel utilisateur

Billion

Billion BiPAC 4700AZ Manuel utilisateur

Billion

Billion BiPAC 5210S Manuel utilisateur

Billion

Billion ADSL Modem / Router BIPAC-710C2 Manuel de la liste des pièces

Billion

Billion 810VGTX Manuel utilisateur

Billion

Billion BiPAC 7404V series Manuel utilisateur

Billion

Billion BIPAC-741 GE V2.0 Manuel utilisateur

Billion

Billion BiPAC 7300 G Manuel utilisateur

Billion

Billion BiPAC 7402 Manuel utilisateur

Billion

Billion BiPAC 8700AX-1600 Manuel utilisateur

Billion

Billion BIPAC 7100G Manuel utilisateur

Billion

Billion BiPAC 7402X Series Manuel utilisateur

Billion

Billion BiPAC 7402(G)X(L) Series Manuel utilisateur

Billion

Billion BiPAC 8500/8520 Manuel utilisateur

Billion

Billion BiPAC 7404V series Manuel utilisateur

Billion

Billion BiPAC 7800NEXL Manuel utilisateur

Billion

Billion BiPAC 8200AXL-1200 Manuel utilisateur

Billion

Billion BiPAC 7402NXL Manuel utilisateur

Billion

Billion BiPAC 7300M Manuel utilisateur

Billion

Billion BIPAC-74x GE Series Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité

LevelOne

LevelOne FBR-1416 Manuel utilisateur