BestScope BS-6000A Manuel utilisateur

Metallurgical Microscope

Model Number

BS-6000A/AT

User Manual

This manual is written for Metallurgical Microscope of BS-6000A/AT. For safety and for

exerting the best performance, making you familiar with the instrument entirely, it is strongly

recommended that you read this manual carefully before using the microscope.

BestScope International Limited

Contents BS-6000A/AT

User Notices

1 Components Name…………………………………………………… 3

2 Installation …………………………………………………………… 4

2.1 Installing Diagram ……………………………………………………… 4

2.2 Installing steps …………………………………………………………… 5

3Adjustment & Operation ………………………………………… 9

3.1Adjustment System Installing Illustration……………………………… 9

3.2 Operation …………………………………………………………………… 11

4 Technical Specifications …………………………………………… 14

5 Trouble Shooting …………………………………………………… 15

BestScope International Limited

Use Notices BS-6000A/AT

I. Safety note

1. Carefully open the box, avoid the accessories, like lens, dropping to ground and being damaged.

2. Do keep the instrument out of direct sunlight, high temperature or humidity, dusty and easy

shaking environment. Make sure the stage is smooth, horizontal and firm enough.

3. When moving the instrument, please use two hands to grip with the two sides of the microscope

body.

4. If the bacterium solution or the water splash to the stage, objective or viewing tube, pull out the

power cord at once, and wipe up the microscope. Otherwise, the instrument will be damaged.

5. When running, the lamp house and nearby parts will be very hot. Please ensure there is enough

cooling room for them.

6. Make sure the instrument is earthed, to avoid lighting strike.

7. For safety, be sure the main switch is in “O”(off) state before replace the halogen lamp or the fuse,

then cut off the power, and do the operation after the lamp bulb and the lamp house completely

cool.

8. Check the input voltage: be sure the input voltage which signed in the back of the microscope is

consistent with the power supply voltage, or it will bring a serious damage to the instrument.

9. Use the factory supplied power cord, please.

II. Maintenance

1. All the lenses have been well checked and adjusted. It is forbidden to disassemble them yourself.

2. The nosepiece and coarse/fine focus unit have a compact and precise frame, please don’t

disassemble them as possible as you can.

3. Keep the instrument clean, wipe dust regularly, and be attention to avoid contaminating the

optical elements especially.

4. The contaminations on the prism, as finger mark and oil, could be gently wiped with a piece of soft

cloth or tissue paper, gauze which has been immersed in pure alcohol or xylene. (note that the

alcohol and the xylene are all burned easily, do not let them near the fire, and use them in a

drafty room as possible as you can.)

5. Don’t use organic solvent to wipe the non-optical elements, when you need to clean, use the soft

detergent, please.

6. When using, if the microscope is splash by liquid, cut off the power at once, and wipe up the

moisture.

7. Do not disassemble any parts of the microscope. That will affect the function or decline the

performance of the microscope.

8. Place the instrument in a cool, dry position. After using the microscope, remember to cover it

with dust helmet. Do wait for the lamp house cooling completely before cover.

BestScope International Limited

1.Name of Components BS-6000A/AT

Eyepiece Binocular viewing head

Metallurgical

Illumination System

Filter Board

Nosepiece

Objective

Body

BestScope International Limited

①②

⑦

2．

Installation BS-6000A/AT

2.1 Installing Illustration

The following shows the installing order of the spare parts. The number expresses the installing process.

Before the installing, make sure there is no dust and stain on the spare parts. No marks by

outside force on the surface of the spare parts or glass.

Keeping the hexagon- spanner well, when change the spare parts, you will use it.

Body

Objective

Metallurgical

Illumination System

Binocular Viewing Head

10X Eyepiece

③

④

Filter Set

⑤⑥

Cable Wire

BestScope International Limited

BS-6000A/AT

2.2 Installing Setps

Fig.2

Fig.1

2.2.1 Installing the Objective (Fig.1-2)

1. Adjust the coarse &fine focus knob, till the

mechanical stage to the low limited place.

2. Screw down the objective to nosepiece from left or

right side, low magnification objective first.

Install all the objective form low to high

magnification following the clock hand.

According to this way to install the objective will

make it easier to change magnification in

operation.

Clean the objective frequently.

At first, use the 10X objective to looking for

image, then change another one.

Turn the objective till hear the “Kai. Kai” sound,

make sure the objective enter the objective

center.

2.2.2 Installing the Metallurgical

Illumination Set (Fig.3-4)

1. Insert the Metallurgical Illumination Set with

Lamp House installed into the Microscope

Body. Align the position and screw down the

bolt with hexagon wrench.

2. Plug the power cord①of the Metallurgical

Illumination Set into the socket②. Then screw

the bolt firmly on the socket.

Fig.3

Fig.4

BestScope International Limited

BS-6000A/AT

Fig.6

Fig.5

Fig.7

2.2.3 Install the binocular viewing head

(Fig.5-6)

Insert the binocular viewing head in the

head of the body, turn to the right place, then

fixupitbybolts

2.2.4 Install the eyepiece (Fig.7-8)

Insert the eyepiece in the eyepiece tube till

end. Fig.8 picture shows the station after

the installing.

Fig.8

BestScope International Limited

Fig.12

BS-6000A/AT

2.2.5 Install the color filter (Fig.9-10)

Put the filter into the jack of the illumination

system.

★There is three type of color filter. The color is

blue, yellow and green.

2.2.6 Connecting the Power Cord (Fig.11-13)

★Do not force on the Power Cord. The cable and

wire are easier to be damaged when bended or

wrapped.

1. Before connecting the power cord, switch the main

On-Off ①to “O”(off).

2. Plug the power cord②into the socket③on

microscope safely. Make sure be connected.

3. Plug the power cord④into the power source

socket⑤safely. Make sure be connected.

★Do use the supplied power cord all the time. If

lost or damaged, select the same standard cord,

please.

★This machine has High-Band voltage. It can

adapt any voltage between 100V and 240V.

2.2.7 Replacing the fuse(Fig.11-12)

Do remember to turn the main switch①on the

state of “O”(off) before replacing the fuse, and

unplug the power cord. Rotate the fuse⑥kits out

of the holder⑦by the “--”type screwdriver,

replace a new fuse, then rotate back to the holder

again.

Fig.9

Fig.10

Fig.11

Fig.13

BestScope International Limited

BS-6000A/AT

Fig.15

Fig.16

Fig.17

2.2.8 Installing and replacing the lamp

(Fig.14-17)

Please use the specified halogen Lamp 6V30W.

1. Pull out the lamp-house①as the picture show

(Fig.14)

2. Hold to the bulb ①after you wrap it with gauze or

other protection materials, then depress the

plugs②into the jack③on the lamp house, ensure

the filament and the bolt④are in a same

level.(Fig.15)

3. Replacing the lamp when using or soon after

When using, or soon after it is turned off, the lamp,

the lamp house and nearby parts will be very hot

and will cause serious burns. Please turn the main

switch on “O” (off), pull up power plug, and make

sure the bulb, the lamp house and periphery are all

cool. Then, you can do your replacing.

Please insert the lamp gently, or it will be

damaged by excessive extrusion.

Do not touch the Halogen bulb with your hands. It

will shorten the service life or cause it to burst. If

you leave fingerprints on the surface carelessly,

clean it with a dry soft cloth.

4. Align the socket①and pins②and align the bolt③

and the jack④. Then push the lamp-house into the

Metallurgical Illumination Set until

covered.(Fig.15-16)

Fig.14

BestScope International Limited

3.Adjustment &Operation BS-6000A/AT

3.1Adjustment Set Diagram (Fig.18-19)

Left Fine Focus Knob

Left Coarse Focus Knob

Interpupillary Distance

Diopter Ring

Light Switch

View field Diaphragm

Aperture Diaphragm

Gather Lens Adjust Lever

Fig.18

Tension

Adjustment Collar

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels BestScope Microscope

BestScope

BestScope BS-3035 Series Manuel utilisateur

BestScope

BestScope BS-2030BD Manuel utilisateur

BestScope

BestScope BS-3080 Series Manuel utilisateur

BestScope

BestScope BS-6024RF Manuel utilisateur

BestScope

BestScope BLM2-241 Manuel utilisateur

BestScope

BestScope BS-3044 Manuel utilisateur

BestScope

BestScope BS-6023 Series Manuel utilisateur

BestScope

BestScope BS-2080MH6 Manuel utilisateur

BestScope

BestScope BS-2030B Manuel utilisateur

BestScope

BestScope BS-2080D Manuel utilisateur

BestScope

BestScope BS-2082 Series Manuel utilisateur

BestScope

BestScope BS-5070B Manuel utilisateur

BestScope

BestScope BS-2053 Series Manuel utilisateur

BestScope

BestScope BS-5095 Manuel utilisateur

BestScope

BestScope BS-2064 Series Manuel utilisateur

BestScope

BestScope BS-6045 Manuel utilisateur

BestScope

BestScope BS-3020 Manuel utilisateur

BestScope

BestScope BS-2030MH10 Manuel utilisateur

BestScope

BestScope BS-7020 Manuel utilisateur

BestScope

BestScope BS-3003 Manuel utilisateur

BestScope

BestScope BS-6005 Manuel utilisateur

BestScope

BestScope BS-2022 Series Manuel utilisateur

BestScope

BestScope BS-2030MH4A Manuel utilisateur

BestScope

BestScope BS-6012 Series Manuel utilisateur

Manuels Microscope populaires d'autres marques

Thermo Scientific

Thermo Scientific Nicolet iN10 Mode d’emploi

National

National DC3-163 Manuel utilisateur

KERN Optics

KERN Optics OPE-1 Manuel utilisateur

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manuel utilisateur

Prior

Prior Lux POL Manuel utilisateur

Opitec

Opitec Smartscoop 115615 Manuel utilisateur

KERN

KERN OPO-1 Manuel utilisateur

Topcon

Topcon SP-1P Manuel utilisateur

Motic

Motic PA43 Manuel utilisateur

Leica

Leica DVM5000 Guide de l'utilisateur

MshOt

MshOt MZ62 Manuel utilisateur

KERN Optics

KERN Optics OZR-5 Manuel utilisateur

VWR

VWR VisiScope 384 Series Manuel utilisateur

Nikon

Nikon ECLIPSE E200 POL Manuel utilisateur

Leica

Leica DI C800 Manuel

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manuel utilisateur

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manuel utilisateur

Olympus

Olympus SZ61 Manuel utilisateur