Belden HIRSCHMANN GRS105 Manuel utilisateur
Installation GRS105/GRS106
Release
01
11/2021
Technical support
https://hirschmann-support.belden.com
User Manual
Installation
Industrial Ethernet Workgroup Switch
GRS105/GRS106
2021-11-02 Installation GRS105/GRS106
Release
01
11/2021
The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2021 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at:
https://www.doc.hirschmann.com
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Installation GRS105/GRS106
Release
01
11/2021 3
Contents
1 About this manual 7
2 General safety instructions 8
2.1 Warning symbols 9
2.2 Intended use 10
2.3 National and international safety regulations 10
2.4 Installation site requirements 10
2.5 Qualification requirements for personnel 11
2.6 Device casing 11
2.7 Strain relief 12
2.8 Shielded ground 12
2.9 Electrical connections 12
2.9.1 Grounding the device 12
2.9.2 Requirements for connecting electrical wires 12
2.9.3 Requirements for connecting the supply voltage 13
2.9.4 Requirements for connecting the signal contact 13
2.10 LED or laser components 13
2.11 Recycling note 14
3 Approvals 15
3.1 CE marking 15
3.2 UKCA marking 16
3.3 FCC note 17
3.4 Relevant for installations in switch cabinets according to
UL 60950-1/UL 62368-1 17
4Key 19
5 Description 20
5.1 General device description 20
5.2 Device name and product code 21
5.3 Device views 22
5.3.1 Front view device variant GRS106-6F8F16T... 22
4Installation GRS105/GRS106
Release
01
11/2021
5.3.2 Front view device variant GRS106-6F8T16T... 22
5.3.3 Rear views 23
5.3.4 Port assignment 24
5.4 Supply voltage 25
5.4.1 Supply voltage characteristic value G 26
5.4.2 Supply voltage characteristic value M 26
5.4.3 Supply voltage characteristic value L 27
5.5 Ethernet ports 28
5.5.1 10/100/1000 Mbit/s twisted pair port 28
5.5.2 100/1000/2500 Mbit/s twisted pair port 28
5.5.3 1/2.5 Gbit/s F/O port 29
5.5.4 1/2.5/10 Gbit/s F/O port 29
5.6 Management interfaces 30
5.6.1 Signal contact 30
5.6.2 Management interface MGMT (external
management) 31
5.6.3 SD card interface 33
5.7 Display elements 34
5.7.1 Device Status 34
5.7.2 Port status 36
6 Installation 39
6.1 Checking the package contents 39
6.2 Installing the SD card (optional) 40
6.3 Installing an SFP transceiver (optional) 41
6.4 Installing the device 41
6.5 Grounding the device 47
6.6 Connecting the terminal blocks 48
6.6.1 Supply voltage characteristic value M 48
6.6.2 Supply voltage characteristic value L 49
6.6.3 Signal contact 50
6.7 Connecting data cables 50
6.8 Filling out the inscription label 51
7 Operating the device 52
8 Making basic settings 53
Installation GRS105/GRS106
Release
01
11/2021 5
8.1 Default settings 53
8.2 First login (Password change) 54
9 Maintenance and service 55
10 Monitoring the ambient air temperature 56
11 Monitoring the ambient humidity 57
12 Disassembly 58
12.1 Removing the device 58
12.2 Removing an SFP transceiver (optional) 59
12.3 Removing the SD card (optional) 60
13 Technical data 61
13.1 General technical data 61
13.2 Supply voltage 61
13.3 Power consumption/power output 62
13.4 Signal contact 62
13.5 Climatic conditions during operation 63
13.6 Climatic conditions during storage 63
13.7 Dimension drawings 64
14 EMC and immunity 65
15 Network range 67
15.1 10/100/1000 Mbit/s twisted pair port 67
15.2 100/1000/2500 Mbit/s twisted pair port 67
15.3 Gigabit Ethernet SFP transceiver 68
15.4 Bidirectional Gigabit Ethernet SFP transceiver 69
15.5 2.5 Gigabit Ethernet SFP transceiver 71
15.6 10 Gigabit Ethernet SFP+ transceiver 71
15.7 DAC cables 72
16 Scope of delivery 73
Installation GRS105/GRS106
Release
01
11/2021 7
1 About this manual
The “Installation” user manual contains a device description, safety
instructions, a description of the display, and the other information that you
need to install the device.
The Network Management Software Industrial HiVision provides you with
options for smooth configuration and monitoring. You find further information
on the Internet at the Hirschmann product pages:
https://www.hirschmann.com/en/QR/INET-Industrial-HiVision
Documentation mentioned in the “User Manual Installation” that is not
supplied with your device as a printout can be found as PDF files for
downloading on the Internet at: https://www.doc.hirschmann.com
8Installation GRS105/GRS106
Release
01
11/2021
2 General safety instructions
Note: Read these instructions carefully, and familiarize yourself with the
device before trying to install, operate, or maintain it. The following notes may
appear throughout this documentation or on the device. These notes warn of
potential hazards or call attention to information that clarifies or simplifies a
procedure.
You operate this device with electricity. Improper usage of the device entails
the risk of physical injury or significant property damage. The proper and safe
operation of this device depends on proper handling during transportation,
proper storage and installation, and careful operation and maintenance
procedures.
Before connecting any cable, read this document, and the safety
instructions and warnings.
Operate the device with undamaged components exclusively.
The device is free of any service components. In case of a damaged or
malfunctioning device, turn off the supply voltage and return the device to
Hirschmann for inspection.
WARNING
UNCONTROLLED MACHINE ACTIONS
To avoid uncontrolled machine actions caused by data loss, configure all
the data transmission devices individually.
Before you start any machine which is controlled via data transmission, be
sure to complete the configuration of all data transmission devices.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.
Installation GRS105/GRS106
Release
01
11/2021 9
2.1 Warning symbols
This is a general warning symbol. This symbol alerts you to
potential personal injury hazards. Observe all safety notes that
follow this symbol to avoid possible injury or death.
If this symbol is displayed in addition to a safety instruction of the
type “Danger” or “Warning”, it means that there is a danger of
electric shock and failure to observe the instructions will inevitably
result in injury.
This symbol indicates the danger of hot surfaces on the device. In
connection with safety instructions, non-observance of the
instructions will inevitably result in injuries.
DANGER
DANGER draws attention to an immediately dangerous situation, which will
inevitably result in a serious or fatal accident if not observed.
WARNING
WARNING indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION
CAUTION indicates a possible danger which, if not avoided, may result in
minor injuries.
NOTICE
NOTICE provides information about procedures that may result in
equipment or environmental damage.
10 Installation GRS105/GRS106
Release
01
11/2021
2.2 Intended use
Use the product only for the application cases described in the
Hirschmann product information, including this manual.
Operate the product only according to the technical specifications.
See “Technical data” on page 61.
Connect to the product only components suitable for the requirements of
the specific application case.
2.3 National and international safety
regulations
Verify that the electrical installation meets local or nationally applicable
safety regulations.
2.4 Installation site requirements
Exclusively operate the device at the specified ambient temperature
(temperature of the ambient air at a distance of 5 cm (2 in) from the device)
and at the specified relative humidity.
When you are selecting the installation location, make sure you observe
the climatic threshold values specified in the technical data.
Use the device in an environment with a maximum pollution degree that
complies with the specifications in the technical data.
See “Technical data” on page 61.
If the device is not installed horizontally, it must be installed in a switch
cabinet or other fire enclosure. The fire enclosure can be made of metal
or plastic with fire protection properties of at least V-1 according to
IEC 60695-11-10. The maximum diameter of bottom openings in the fire
enclosure is 2 mm (0.078 in).
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Belden Changer
Belden
Belden Hirschmann SPIDER-SL-20-01T1S29999SZ9HHHH Manuel utilisateur
Belden
Belden Hirschmann MACH4002 Series Manuel utilisateur
Belden
Belden Hirschmann GREYHOUND GRS1042 Manuel utilisateur
Belden
Belden Hirschmann MICE MS20 Manuel utilisateur
Belden
Belden Grass Valley K-Frame Comment utiliser
Belden
Belden HIRSCHMANN SPIDER II Manuel utilisateur
Belden
Belden lumberg automation 0960 IOL 3816-001 Manuel utilisateur
Belden
Belden HIRSCHMANN EESX Series Guide de configuration rapide
Belden
Belden HIRSCHMANN GREYHOUND GRM Series Manuel utilisateur
Belden
Belden Hirschmann MACH104-PoEP Series Manuel utilisateur
Belden
Belden Hirschmann SPIDER II 8TX Manuel utilisateur
Belden
Belden Grass Valley Kayenne Supplément
Belden
Belden Hirschmann RS20 U Series Manuel utilisateur
Belden
Belden grass valley SIRIUS 800 Series Guide de l'utilisateur
Belden
Belden Hirschmann SPIDER-SL-20-08T1999999SY9HHHH Manuel utilisateur
Belden
Belden grass valley KULA AV Manuel utilisateur
Belden
Belden HIRSCHMANN SPIDER II 16TX EEC Manuel utilisateur
Belden
Belden HIRSCHMANN OCTOPUS OS24 Series Manuel utilisateur
Belden
Belden Hirschmann SPIDER Standard Line Series Manuel utilisateur
Belden
Belden Hirschmann RED25 Series Manuel utilisateur
