Automatic Technology 62717 Manuel utilisateur

Doc # 160072_04

Released 01/04/20

GDO-6 EasyRoller®

Rolling Door Opener

Installation Manual

GDO-6 EasyRoller Installation Manual

Table of Contents

1. Installation Safety Warnings! 3

2. Kit Contents 4

3. Tools Required 4

4. Setup Requirements 5

5. Door Preparation 6

6. Fit the Weight Bar 6

7. Pinning the Door 7

8. Proping the Door 7

9. Mounting the Opener 8

9.1 Raising the Door: 8

9.2 Mounting the Opener: 8

10. Setting the Travel Limits 9

10.1 Initial Preparation: 9

10.2 Set the Limit Positions: 9

10.3 Resetting the Door Limit Positions 9

10.4 Setting the PET Mode position 9

10.5 Reset all Factory Defaults 9

11. Safety Testing 10

11.1 Test the Close Cycle 10

Testing the Open Cycle 10

11.2 Test the Manual Door Operation 10

11.3 Adjusting Safety Obstruction Force 10

11.4 To Increase Force Pressure 10

11.5 To Decrease Force Pressure 10

11.6 To Recall Factory Set Force 10

11.7 To Recalculate Force Margins 10

12. Accessories 11

12.1 Auxiliary Output 11

12.2 Keyswitch Connection 11

12.3 Remote Aerial 11

13. Auto-Close 11

13.1 Safety Beams 11

13.2 Auto Close Option 11

14. Coding a Transmitter 12

14.1 Storing the Transmitter Code 12

14.2 Coding a Button to Enable Vacation Mode 12

14.3 Coding to enable AUX Output 12

14.4 Setting to Operate PET (Pedestrian) Mode 12

14.5 Coding a Transmitter to the Courtesy Light 12

14.6 Easy Access Transmitter (EAT) Coding 13

14.7 Remotely Coding Transmitters 13

14.8 Erasing a Stored Transmitter Code 13

14.9 Erasing All Transmitter Codes 13

Installation Instructions

Home Owner Instructions

15. Home Owner Safety Warnings! 14

16. Opener Safety & Security 15

16.1 Your Door CAN NOT be used when: 15

16.2 Your Door CAN be used when: 15

16.3 To Disengage the Opener: 15

16.4 To Re-Engage the Opener: 15

17. Operating your Opener 15

18. User Operating Controls 16

19. Door Status Indicators 16

20. Specifications 17

21. Troubleshooting 18

22. After Installation Care 20

22.1 Service Checklist 20

22.2 Battery Replacement 21

22.3 Battery Disposal 21

22.4 Warranty 21

GDO-6 EasyRoller Installation Manual

1. Installation Safety Warnings!

WARNING! • The door may operate unexpectedly, therefore do not allow anything to stay in the path of

the door.

• When operating the manual release while the door is open, the door may fall rapidly due

to weak or broken springs, or due to being improperly balanced.

• The drive must not be used with a door incorporating a wicket door, unless the drive cannot

be operated with the wicket door open.

• The drive is intended to be installed at least 2.5m above the floor.

• Do not disengage the opener to manual operation with children/persons or any objects

including motor vehicles within the doorway.

• If the door is closing and is unable to re-open when obstructed, discontinue use. Do not

use a door with faulty obstruction sensing

• When using auto close mode, a Photo Electric beam must be fitted correctly and tested

for operation at regular intervals. Extreme caution is recommended when using auto close

mode. All safety rules must be followed.

ELECTROCUTION! • Place opener in protected area so that it does not get wet.

• Do not spray with water .

• Disconnect the power cord from mains power before making any repairs or removing covers.

Only experienced service personnel should remove covers from the opener.

• If the power supply cord is damaged, it must be replaced by an Automatic Technology

service agent or suitably qualified person.

• Connect the opener to a properly earthed general purpose 240V mains power outlet

installed by a qualified electrical contractor.

CAUTION:

Emergency Access • If garage has no pedestrian entrance door, an emergency access device should be

installed. This accessory allows manual operation of the garage door from outside in case

of power failure.

Muscular strain • Practice correct lifting techniques (carton weighs approx 9kgs)

• Practice correct lifiting techniques when required to lift the door as per installation instructions.

Fall from ladder • Ensure ladder is the correct type for job.

• Ensure ladder is on flat firm ground that will take the weight without the legs sinking.

• Ensure user has 3 points of contact while on ladder.

Crush injury from unsecured

door

• Place a 2 metre exclusion zone around area under the door while it is unsecured.

• Do not move under a door while it is on the door support (or ladder)

• Follow the installation instructions

• Fit door support (or ladder) snugly under door before removing bracket.

• Ensure door support (or ladder) is on flat ground

Garage Door • Examine the door installation, in particular, springs and mountings for signs of wear, damage

and imbalance.

• The garage door must be well balanced. Sticking or binding doors must be repaired by a

qualified garage door installer prior to installation of the opener.

• Remove or disengage all garage door locks and mechanisms prior to installation of the opener.

Entanglement • Never plug in and operate opener prior to installation.

• Keep hands and loose clothing clear of door and guides at all times.

Entrapment under

operating door

• DO NOT operate the opener unless the garage door is in full view and free from objects

such as cars and children/people. Make sure that the door has finished moving before

entering or leaving the garage

• In order for the opener to sense an object obstructing the door way, some force must be

exerted on the object. As a result the object, door and/or person may suffer minor damage

or injury.

• Ensure the garage door is in good working order by undertaking regular servicing.

• Install the optional wall transmitter in a location where the garage door is visible, but out

of the reach of children at a height of at least 1.5m.

• Photo Electric beams must be installed if the closing force at the bottom edge of the door

exceeds 400N (40kg)

This automatic garage door opener is designed and tested to offer safe service provided it is installed

and operated in strict accordance with the following safety warnings. Failure to comply with the following

instructions may result in death, serious personal injury or property damage.

GDO-6 EasyRoller Installation Manual

2. Kit Contents

1. 1 x drive unit

2. 2 x Locking Bar Covers

3. 2 x PTX-6 Transmitters (GDO-6V4) OR

2 x PTX-5V2 Transmitters (GDO-6V3)

4. 1 x Weight Bar

Fastner Bag

5. 2 x Nilock Nut

6. 2 x 3/16 x 1/2 flat washers

7. 2 x Pan Head Screw M4 x 50mm

Screwdrivers

Adjustable End Wrench

Sockets and Wrench

Pencil

Rope

Drill

Towel

Self-tapping Screws and Washers

(M10 x 32mm)

Stepladder

Door Stand

or suitable prop

3. Tools Required

GDO-6 EasyRoller Installation Manual

WARNING! A portable power generator

is not recommended due to spikes, surges

and fluctuations in the supply.

175

135

Minimum Side room Recommended Side room

4.2 Unsuitable Door Types

The drive must not be used with a door incorporating a wicket

door, unless the drive cannot be operated with the wicket door

open. The fitting of an opener to doors with removable mullions

is not recommended.

4.3 Sideroom

The minimum sideroom required from the edge of the door curtain

is 40mm to the inside of the door bracket, and 85mm to the wall.

If a Battery Backup is to be fitted, at least 135mm to the bracket

is required.

Therefore the recommended sideroom from the edge of the door

curtain is 135mm to the inside of the door bracket, and 175mm to

the wall as per diagram.

4. Setup Requirements

4.1 The Opener:

a. MUST BE installed in a dry position, protected from weather. (Moisture or corrosion not covered by Warranty)

b. Is factory set for RIGHT HAND SIDE installation (from inside garage), but capable of LEFT HAND SIDE installation.

c. REQUIRES properly earthed 3 pin single phase power within an arms length of door and at a suitable height

d. Requires a MINIMUM SIDEROOM of 40mm from the edge of the door to the inside of the door bracket and 85mm to the

wall.

e. CAN NOT be installed on a Door Axle Diameter that exceeds 35mm.

LEFT HAND SIDE RIGHT HAND SIDE

40mm 40mm

85mm

GDO-6 EasyRoller Installation Manual

6.1 If the door has a handle a weight bar must be fitted to ensure the door doesn’t balloon during operation:

a. Remove the door handle

b. Fit the weight bar 4and refit the handle using the two (2) M4x50mm Pan Head Screw 7and the two (2) Flat Washer 6

and the two (2) M4 Nilock Hex nut 5.

6.2 If the door does not have a handle:

a. Locate the centre of the door at the bottom rail.

b. Place the weight bar at this point and mark the two positions where the fasteners will go

c. Drill the two 4.5mm holes in the door and fit the weight bar 4using the two (2) M4x50mm Pan Head Screw 7and the

two (2) Flat Washer 6and the two (2) M4 Nilock Hex nut 5.

d. Check that the door is still balanced and smooth. If not, then the door may require servicing.

5. Door Preparation

5.1 Prepare the Door:

a. Clean the guides if there is any oil or wax present using a suitable white spirit. The only lubricant suitable for use on door guides

is silicon spray. DO NOT use WD-40, RP-7, petroleum grease, or similar.

b. Remove the locking bars or disable the lock.

c. Install the locking bar covers 2if there are locking bar holes in the guides. This ensures fingers cannot be placed in the

holes while the door operates

d. Affix the supplied warning labels where they are clearly visible on the inside of the door.

6. Fit the Weight Bar

WITH HANDLE WITHOUT HANDLE

GDO-6 EasyRoller Installation Manual

7. Pinning the Door

7.1 Pinning the Door to the drum:

Pinning the door’s curtain to its drum maintains security when the opener is

closed. If the curtain is not pinned the door can be partially opened manually.

a. Fully close the door.

b. Mark a minimum of two (2) drill holes on the drum to each end of the door.

c. Drill holes using 3.2mm (1/8”) drill bit.

d. Fit M10 x 32mm screws and washers (not supplied) to each of the four (4)

holes. This screw should be positioned as low as possible in the grove, but

make sure that it does not alter the curtain’s normal lead in to the guide.

BALLOONING DOOR

PINNED DOORFREE DOOR

Without locking

bars door can be

lifted

Not pinned and

without locking

bars door can be

lifted

Door secure and

will not lift

Pin Points

Screw into the

low part of

grove

8. Proping the Door

8.1 Prepare the Door:

a. At the end opposite to where the opener will be fitted, check that the U-bolt

which holds the door axle to the bracket is tightened securely.

b. Open the door completely and tie rope around the door roll. Do not tie the

rope too tight as damage to the curtain may ensue. This will stop the door

unrolling when taken off the bracket

c. At the end where the opener is to be fitted, support the door with a door stand

or suitable prop. Place a towel between the door and the prop to protect the

door from damage.

d. At the end where the opener will be fitted use a pencil to mark the position of

the U-bolt in the door bracket and the position of the door bracket on the wall

to assist in reassembling.

WARNING! The U-bolt must be done up tightly to ensure

the stored energy in the springs cannot be unexpectedly

released.

WARNING! Make sure the prop is

snug under the door and is stable.

U-bolts

Towel

Door stand

or prop Door

bracket

GDO-6 EasyRoller Installation Manual

9.1 Raising the Door:

a. When in position, remove the U-bolt (or bolts) and saddle from the

door bracket.

b. Lift the door up and away from the wall until clear of the door

bracket, before lowering the door to rest on the door stand or prop.

NOTE: If there is limited ceiling space to lift the door, the door bracket

may have to be removed. If this is required, when refitting the door

bracket , use the reference marks on the wall for correct position and

ensure that it is secure to the wall and will support the door.

9. Mounting the Opener

Lift door

up, away

from wall

and down

onto prop

WARNING! For tight sideroom

installations the door may have to

be taken down.

9.2 Mounting the Opener:

a. Remove the opener from the box.

b. Check the drive gear rotates freely, by pulling the string handle

down (there will be a click) to disengage opener. Then move the

forks from side to side by hand.

c. Slide the opener over the door axle and into the drum of the door

as shown.

d. Push the opener in as far as possible (without interfering with the

curtain) SO ONE OF THE DOOR DRUM’S WHEEL SPOKES IS

BETWEEN THE OPENER’S DRIVE FORKS.

e. Raise the door off the door stand or suitable prop.

Tighten

U-bolts

Pull string

down to

disengage

opener

Slide

opener

over door

axle

f. Lift up and over the door bracket and use your reference marks on

the door bracket to position the door.

g. Refit the U-bolt and nuts and tighten.

h. Remove the safety rope and door stand or prop.

i. Connect the power cort to a suitable powerpoint, but DO NOT

switch on.

j. Secure the power cord away from any moving object (e.g the door)

with the cable clip supplied.

k. With the opener still disengaged, pull the door up and down to

make sure it runs freely.

GDO-6 EasyRoller Installation Manual

10. Setting the Travel Limits

10.1 Initial Preparation:

a. Move the door to the half way position.

b. Engage the opener by pulling down on the manual release

string until a click sounds.

c. Remove the clear button cover from the unit.

d. Switch power on to the opener. The red CLOSE LIMIT LED will

be flashing.

e. Press and hold the CLOSE button - the door should start

closing.

NOTE: If the door opens, release the CLOSE button and press

the OPERATE button once to change the motor’s direction.

Pull string

down to

engage

opener

10.2 Set the Limit Positions:

The Limit Positions can vary due to site conditions, such as uneven

ground. When setting the Close limits, ensure the position is when

the door makes first contact with the ground. Alternatively for the

Open limits the position should be at the height of the garage

opening.

a. Press and hold CLOSE button until the door reaches your

desired close limit position. The rubber strip at the bottom of

the door should form a good seal with the ground.

b. Release the CLOSE button when the door is near the desired

closed position. Single presses of the CLOSE button will inch

the door closer to the ground.

c. If the door overshoots press the OPEN button to move the

door in the open direction.

d. When the door is at the desired close position, press the SET

button, the OPEN LIMIT LED will now flash.

e. Press and hold the OPEN button until the door reaches your

desired open limit position. Single presses of the OPEN button

will inch the door open.

f. If the door overshoots press the CLOSE button to move the

door in the close direction.

g. When the door is at the desired open position, press the SET

button.

WARNING! In setting the close limit position, do

not force the door into the floor with excessive

force, as this can interfere with the ease of

operation of the manual release mechanism.

h. The door will now automatically close and open to calculate

the safety obstruction settings.

10.3 Resetting the Door Limit Positions

Limit positions can be deleted by:

a. Press and hold CLOSE button for six (6) seconds until the

CLOSE LIMIT LED flashes quickly.

b. Release the CLOSE button.

NOTE: If no action is taken within 30 seconds, the opener will

return to normal operating mode and restore the original settings.

c. Follow steps a - f in Set the Limits Poisitions to set new limit

positions.

WARNING! The door will automatically close,

open and close again after the next step. Ensure

that nothing is in the door’s path.

10.4 Setting the PET Mode position

When activated, PET mode drives the door to a preset

position from the close position, therefore allowing a

pet or parcel to go under the door.

a. Drive and stop the door at the deisred PET mode open

position by pressing the transmitter button coded for

Open/Stop/Close operation.

b. Press and hold the OPEN button on the opener for six

(6) seconds until the OPEN and CLOSE LED’s are lit to

record the new PET position.

c. Release the OPEN button.

10.5 Reset all Factory Defaults

a. Turn power to the opener off.

b. Press and hold the SET Button.

c. Turn power on while holding the SETbutton. Continue

to hold until all LED’s are off.

d. This will NOT erase transmitter codes stored in

memory.

GDO-6 EasyRoller Installation Manual

11. Safety Testing

11.1 Test the Close Cycle

a. Press the OPERATE button to open the door.

b. If the door closes, press the OPERATE button to stop the door,

then press OPERATE again to open.

c. Place a piece of timber approximately 40mm high (or the openers

cardboard box) on the floor directly under the door.

d. Press the OPERATE button to close door.

e. The door should strike the object and re-open.

f. Remove the timber or cardboard box.

Testing the Open Cycle

a. Press the OPERATE button to close the door.

b. Press OPERATE again to open the door.

c. When the door reaches approximately half way, firmly grab the

door’s bottom rail - the door should stop.

If the door does not reverse readily when closing, or stop when

opening, put the door into manual by pulling down on the manual

release string to diesengage the motor and contact 1300 133 944

for support.

11.2 Test the Manual Door Operation

Periodically disengage the opener and manually operate the door.

The door must be smooth to operate by hand. The force required on

the bottom rail should not exceed 20 kg.

CAUTION: Take care when completing a

safety test. Failure to follow this warning

can result in serious personal injury and/or

property damage.

WARNING! If the door is closing and is unable

to re-open when obstructed, discontinue use.

Do not use a door with faulty obstruction sensing.

Wood 40mm

high or opener

cardboard box

11.6 To Recall Factory Set Force

a. Holding down the FORCE MARGIN SET button

and the SET button for two seconds.

b. Release both buttons. The default setting should

now be recalled.

11.7 To Recalculate Force Margins

a. Press and hold the FORCE MARGIN SET Button for

six (6) seconds, the beeper will sound once.

b. The door will start to move and re-calculate force

margins. The door can move between the open and

close limit positions up to four (4) times (depending

on the position of the door and the power up

condition).

c. A single beep will be heard once the process is

complete.

d. Test the force again as per Testing Close Cycle and

Testing Open Cycle.

11.3 Adjusting Safety Obstruction Force

The Safety Obstruction Force is calculated automatically during

setup. Adjusting this is normally only necessitated by environmental

conditions such as windy or dusty areas, and areas with extreme

temperature changes.

11.4 To Increase Force Pressure

a. Press and Hold down the FORCE MARGIN SET button.

b. While holding the FORCE MARGIN SET button, press the OPEN

button. Each press will increases the force margin.

c. The OPEN LIMIT LED will flash each time the OPEN button is

pressed to indicate an increase in force.

d. If the OPEN LIMIT LED flashes continuously when the OPEN

button is being pressed, this indicates that the maximum force

setting has been reached.

e. Test the force again as per Testing Close Cycle and Testing Open

Cycle.

11.5 To Decrease Force Pressure

a. Press and Hold down the FORCE MARGIN SET button.

b. While holding the FORCE MARGIN SET button, press the CLOSE

button. Each press will decrease the force margin.

c. The CLOSE LIMIT LED will flash each time the CLOSE button is

pressed to indicate a decrease in force.

d. If the CLOSE LIMIT LED flashes continuously when the CLOSE

button is being pressed, this indicates that the minimum force

setting has been reached.

e. Test the force again as per Testing Close Cycle and Testing Open

Cycle.

WARNING! If the door fails these tests,

put the opener into manual mode, only

operate the door by hand and call for

service.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Automatic Technology ouvre-porte de garage

Automatic Technology

Automatic Technology Axess Pro Series Manuel utilisateur

Automatic Technology

Automatic Technology Toro GDO-10v2 Manuel utilisateur

Automatic Technology

Automatic Technology GDO-10V3L2 Toro Manuel utilisateur

Automatic Technology

Automatic Technology GDO-2 SecuraLife Manuel utilisateur

Automatic Technology

Automatic Technology Toro GDO-10V2L2 Manuel utilisateur

Automatic Technology

Automatic Technology Dominator AM800 Manuel utilisateur

Automatic Technology

Automatic Technology GDO-11V3 Ero Manuel utilisateur

Automatic Technology

Automatic Technology Hiro GDO-12V1 Manuel utilisateur

Automatic Technology

Automatic Technology GDO-6v4 EasyRoller Manuel utilisateur

Automatic Technology

Automatic Technology HiRO GDO-12 Manuel utilisateur

Automatic Technology

Automatic Technology GDO-9 Dynamo Gen 2 Manuel utilisateur

Automatic Technology

Automatic Technology SecuraLift GDO-7V1 Guide de démarrage rapide

Automatic Technology

Automatic Technology NeoSlider TrioCode 128 NES-500 Manuel utilisateur

Automatic Technology

Automatic Technology GDO-8v1 EasyRoller II Manuel utilisateur

Automatic Technology

Automatic Technology AM-808 Manuel utilisateur

Automatic Technology

Automatic Technology GDO-6v3 EasyRoller Manuel utilisateur

Automatic Technology

Automatic Technology GDO-4 EasyRoller Manuel utilisateur

Automatic Technology

Automatic Technology GDO-6 v2 Manuel utilisateur

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Manuel utilisateur

Automatic Technology

Automatic Technology SecuraLift Rhino Manuel utilisateur

Automatic Technology

Automatic Technology GDO-11v1 Ero Guide de démarrage rapide

Automatic Technology

Automatic Technology GDO-2 SecuraLift Manuel utilisateur

Automatic Technology

Automatic Technology SECURALIFT Guide de démarrage rapide

Automatic Technology

Automatic Technology GDO-11 Ero Manuel utilisateur

Manuels ouvre-porte de garage populaires d'autres marques

Dorma

Dorma ES 90 Manuel utilisateur

Garaga

Garaga SECURITY+ 3265GCM 1HP Manuel utilisateur

Chamberlain

Chamberlain Whisper Drive SECURITY+ WD822K Series Manuel utilisateur

Chase Doors

Chase Doors DuraShield Manuel utilisateur

CSI

CSI Classic Manuel utilisateur

HATO

HATO 120 Manuel utilisateur

Chamberlain

Chamberlain Elite 3575S Manuel utilisateur

Richmond

Richmond GTR156 Manuel utilisateur

Raynor

Raynor 1280RGD Manuel utilisateur

CAME

CAME F4000 Series Manuel utilisateur

B&D

B&D Controll-A-Door 5 Manuel utilisateur

BFT

BFT PRV AA SL Manuel utilisateur

Craftsman

Craftsman 139.53924 Manuel utilisateur

Chamberlain

Chamberlain MyQ 940ESTD Manuel utilisateur

Westfalia

Westfalia 19 36 07 Manuel utilisateur

Chamberlain

Chamberlain HD520EVP Manuel utilisateur

Cardin

Cardin BL Series Manuel utilisateur

Chamberlain

Chamberlain 8355 - 1/2 hp Manuel utilisateur