Audiovox Pursuit PRO-OE3B3 Mode d'emploi

128-6121

1 of 4

TRANSMITTERPROGRAMMINGGUIDE

Model:PRO-OE3B3

The transmitters included with the security system have been pre-programmed

at the factory, with each button pre-assigned to control a specific function of the

security system. Although the security system in the vehicle has either a 3 or 4

channel receiver, depending on the model, the transmitters included with the

system are capable of transmitting 7 distinct signals. This allows you to program

each transmitter to more than one vehicle in two car families and also allows you

to change which button(s) control certain functions of the system.

(Example: Transmitter channel 5 can be programmed to activate Receiver

channel 2.) Refer to the chart below for access to each of the transmitter channels,

and for the standard factory button assignments.

Released 7-17-01.

Some of the more common accessories for these additional channels are;

AS 9554 Remote Garage Door Interface

AS 9075 Remote car starter

AS 9153 Remote window roll up

AS 9256 Remote trunk release relay

TRANSMITTER SYSTEM RECEIVER

CHANNEL BUTTON CHANNEL FUNCTION

Remote Arm

1 1 Remote Emergency Panic

Remote Door Lock

Remote Disarm

2 2 Remote Emergency Panic

Remote Door Unlock/Unlock 2

4& 4

5& 5

6 & 6 RF Channel For Options

7 7 RF Channel For Options

All 3

Buttons

Single Push Pulsed Output for Optional Accessory

Or Double Push For Additional Optional Accessory

Single Push Pulsed Output for Optional Accessory

Or Push And Hold For Extended Output

Single Push Pulsed Output for Optional Accessory

Or Push And Hold For Extended Output

128-6121

2 of 4

PROGRAMMINGTHETRANSMITTERS

It is important to remember that during programming, each individual step of

the procedure must be executed within 15 seconds of the previous step.

Whenthe15secondtimelimitisallowedtoexpire,thesystemwillautomatically

terminate the programming mode. This is indicated by a long chirp from the

siren.

NOTE: Some keyless entry systems will flash the interior light to indicate a

stored code. Substitute the words light flash below where indicated

sounding device will beep.

Additionally, the system will store codes from up to four different transmitters.

If a 5th transmitter is programmed to any receiver channel, then the first

transmitter programmed to that channel will be erased from the system's

memory.

To Program replacement or additional transmitters:

1. Enter the vehicle, and turn the ignition key to the "on" position.

2. Press and release the valet push-button switch 3 times.

3. The dash LED will flash one time and the sounding device will beep one

time, indicating the system is ready to accept programming for receiver's

Lock channel 1.

4. PressandholdtheLocktransmitterbuttonuntilthesoundingdeviceemits

a long beep, indicating the signal has been stored into memory.

5. If you have additional transmitters (up to 4) that need to be programmed,

repeat step 4 for each transmitter.

6. Press and release the valet push-button switch once.

7. The dash LED will flash two times and the sounding device will beep two

times,indicatingthesystemisreadytoaccept programmingforreceiver's

Unlock channel 2.

8. Press and hold the Unlock transmitter button until the sounding device

emits a long beep, indicating the signal has been stored into memory.

9. If you have additional transmitters (up to 4) that need to be programmed,

repeat step 8 for each transmitter.

10. Press and release the valet push-button switch once.

11. The dash LED will flash three times and the sounding device will beep

three times, indicating the system is ready to accept programming for

receiver's channel 3.

12. Press and hold the selected Option transmitter button until the sounding

device emits a long beep, indicating the signal has been stored into

memory.

13. If you have additional transmitters (up to 4) that need to be programmed,

repeat step 12 for each transmitter.

128-6121

3 of 4

14. Press and release the valet push-button switch once.

15. ThedashLED willflash fourtimesandthesounding devicewillbeepfour

times,indicatingthesystemisreadytoacceptprogrammingforreceiver's

channel 4.

16. Press and hold any button combination as shown on the front cover of

thisguideuntilthesoundingdeviceemitsalongbeep,indicatingthesignal

has been stored into memory.

17. If you have additionaltransmitters(up to 4) that need to be programmed,

repeat step 16 for each transmitter.

18. Press and release the valet push-button switch once.

19. The dash LED will flash four times, and the sounding device will beep

four times, indicating the system is ready to accept programming for

receiver's channel 5.

20. Press and hold any unused button combination as shown on the front

coverofthisguideuntilthesoundingdeviceemitsalongbeep,indicating

the signal has been stored into memory.

21. If you have additionaltransmitters(up to 4) that need to be programmed,

repeat step 20 for each transmitter.

22. Turn the ignition key off. The sounding device will emit one short beep

followed by one long beep indicating the system has terminated the

program mode.

TRANSMITTERBATTERYREPLACEMENT

You will notice a decrease in transmitter range as the battery condition

deteriorates. Transmitter battery replacement is recommended at least

every 10 to 12 months, depending upon how frequently the transmitter is

used.

ThetransmitterhasasmallLEDvisiblethroughthecase.ThisLEDcanbeused

to indicate battery condition. If the LED does not illuminate, then the battery

is discharged, and must be replaced.

To replace the transmitter battery:

1. Remove the small phillips head screws

from the bottom cover of the transmitter.

2. Carefully unsnap the top cover of the

transmitter from the bottom cover.

3. Removethedischargedbattery,making

note of the location of the + and - contacts, and replace with a new type

GP 27A 12 volt battery.

4. Replace the transmitter cover, taking care not to damage the LED or

switches on the circuit board, and secure with the small phillips head

screw.

128-6121

4 of 4

ORDER FORM FOR 3 BUTTON TRANSMITTER

MODEL NO. PRO-OE3B3

IMPORTANT : To help us expedite your order, please print all of the information legibly,

and mail this form and your payment according to the instructions below.

Note: Order Pad # 70 if your Lock & Unlock Icons are White

Order Pad # 71 if your Lock & Unlock Icons are Red.

Note: Transmitter model number found on back of case. ___________

1. Name : ____________________________________________________

Address: _____________________________________________________

City : _____________________ State : _______ Zip Code : ____________

2.Telephone Number : ( _______)_________________________________

3. Enter the total number of transmitters required here : ________________

4. List model number of your actual transmitter pad as shown on page 4 of this

manual: _________________________

5. The cost per transmitter is $ 65.00.

6. Enter the total amount enclosed here : ____________________________

(New York state residents must include the appropriate sales tax.)

7. Method of payment; check one of the boxes below.

!Mastercard !Visa !Check or money order * ( do not send cash )

* Make checks payable to Audiovox Corporation

8. Credit Card Number : ________________________________________

9. Credit Card Expiration Date : _____________________

Credit card purchasers can order additional or replacement

transmittersby phone. Simply dial 1 -800-645 - 4994, and follow

the instructions from the operator interface.

10. Mail this form, and your check, to ;

Audiovox Electronics Corp., 150 Marcus Blvd. Hauppauge, N.Y., 11788

Attn.:TRANSMITTER DEPARTMENT

Table des matières

Autres manuels Audiovox Émetteur

Audiovox

Audiovox PurSuit 091BPr Mode d'emploi

Audiovox

Audiovox ACA300 Manuel utilisateur

Audiovox

Audiovox 5BCR03A Mode d'emploi

Audiovox

Audiovox S1BTXA Mode d'emploi

Audiovox

Audiovox Pursuit 095BPr Mode d'emploi

Audiovox

Audiovox Pursuit 093BPr Mode d'emploi

Audiovox

Audiovox Pursuit PRO-OE2 Mode d'emploi

Audiovox

Audiovox Prestige 07S1BP Mode d'emploi

Audiovox

Audiovox 128-5971 Instructions de montage

Audiovox

Audiovox AX-2K4 Mode d'emploi

Audiovox

Audiovox Pursuit PRO-OE2B Mode d'emploi

Audiovox

Audiovox Prestige APS-2K4 Mode d'emploi

Audiovox

Audiovox AVX01BT3CL3 Mode d'emploi

Audiovox

Audiovox AA-99BT2 Mode d'emploi

Audiovox

Audiovox UltraGuard UG-OE3 Mode d'emploi

Audiovox

Audiovox Prestige APS-2K4 Mode d'emploi

Audiovox

Audiovox Prestige 101BP Manuel du propriétaire

Audiovox

Audiovox PurSuit 08SPr Mode d'emploi

Audiovox

Audiovox Pursuit 095BPr Mode d'emploi

Audiovox

Audiovox Prestige APS-92BT-CL Guide de dépannage

Audiovox

Audiovox AA923-AA94BT Manuel du propriétaire

Audiovox

Audiovox PRO94BT2 Mode d'emploi

Audiovox

Audiovox PurSuit 09XR1Pr Mode d'emploi

Audiovox

Audiovox PRO-94FR Mode d'emploi

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur