Audiovox AVX01BT3CL3 Mode d'emploi
128-6105
1 of 6
1
Model AVX01BT3CL3
Released 7-25-01.
TRANSMITTERPROGRAMMINGGUIDE
The transmitters included with the system have been pre-programmed at
the factory, with each button pre-assigned to control a specific function of
thesystem.Althoughthesysteminthevehiclehaseithera3,4,or5channel
RECEIVER, depending on the model, the transmitters included with the
system are 7 channel transmitters. This allows you to program each
transmitter to more than one vehicle in two car families and also allows you
to change which button or buttons control certain functions of the system.
(Example: Transmitter channel 5, shown below, can be programmed to
activate Receiver channel 2.) Refer to the chart below for access to each of
the transmitter channels, and for the standard factory button assignments.
TRANSMITTER SYSTEMRECEIVER
CHANNEL BUTTONS CHANNEL FUNCTION
1 1 RemoteArm
* Remote Emergency Panic
**Remote Door Lock
2 2 RemoteDisarm
*RemoteEmergencyPanic
***Remote Unlock Drivers Door
**Remote Unlock All Doors
3 3 Push And Hold For 3 Seconds For Opt1
Release, Push 2 Times For Aux. Out.
4 4 **** Pulsed Output for Accessories
5 5 **** Switched Output for Accessories
6 - **** RF
7 - **** RF
&
&
&
&&
* Remote Emergency Panic is available only on certain models.
** Door Lock/Unlock may require additional components in certain vehicles.
*** Unlock Driver Door or Unlock All Doors May Require Additional Components
**** Some of the more common accessories for these additional channels are;
AS 9075 Remote Car Starter
AS 9256 Remote Trunk Release Relay
AS 9154 Remote Garage Door Interface
AS 9153 Remote Window Roll Up
128-6105
2 of 6
2
PROGRAMMINGTRANSMITTERS:
Itisimportanttorememberthatduring programming, each individual step of
the procedure must be executed within 15 seconds of the previous step.
When the 15 second time limit is allowed to expire, the system will
automaticallyexitprogrammode. Thisisindicatedbyalong"chirp"fromthe
siren.
Additionally, any time the ignition key is turned off while programming, the
systemwill immediately exit program mode. Thisis also indicated by along
"chirp" from the siren.
These steps must be initiated within 15 seconds of the ignition switch being
turned on.
TOPROGRAMADDITIONALTRANSMITTERS:
Note: The programming information described below assumes that the
defaulttransmitterisbeingusedandtheLock&Unlockiconsareonseparate
buttons. If you have the optional transmitter with the Lock/Unlock icon on
the same button, use letter "B" reference below for programming, (B
programming not available on all models),
Also, where indicated that the siren will emit a long chirp tone, the optional
horn may be connected instead of or along with the siren in which case
either or both the horn and siren may sound.
If the system you have is a keyless entry unit and not an alarm, there may
be no sounding device.
For units with a toggle switch instead of a pushbutton switch, where
indicated to press and release the pushbutton, instead move the toggle
switch on then off.
1. (a) Enter the vehicle and turn the ignition key to the "on" position.
(b) Enter the vehicle and turn the ignition key to the "on" position.
2. (a) Press and release the valet/bypass push button switch 3 times.
(b) Press and release the valet/bypass push button switch 3 times.
3. (a) The dash LED will flash one time, and the siren will "chirp" 1 time
indicating the system is ready to accept programming for channel 1,
Arm/Lock and Panic.
(b) The dash LED will flash one time and the siren will "chirp" 1 time
indicating the system is ready to accept programming for channel 1,
Arm/Disarm, Lock/Unlock and Panic.
4. (a) YoucanassigntheLock/Armbuttonbypressingandholdingthelock
button until the siren emits a long chirp tone.
128-6105
3 of 6
3
Thechirptoneconfirms that programmingofchannel1wassuccessful.
Upto4transmitterscanbeprogrammed,pressandholdtheselected
button of each additional transmitter until the chirp tone is heard, or
move to step #5
(b) You can assign the Lock/Unlock, Arm/Disarm button, by pressing
and holding the lock/unlock button until the siren emits a long chirp
tone.
The chirp tone confirms that programming of channel 1 was
successful.Upto4 transmitters canbeprogrammed, press and hold
the selected button of each additional transmitter until the chirp tone
is heard, or press and release the valet pushbutton switch two times
to advance to step #8.
5. Press and release the valet/override switch one time to advance to
channel 2.
6. (a) The dash mounted LED will flash 2 times, and the siren will "chirp"
2timesindicating thatthesystemisreadytoacceptprogrammingfor
channel 2. Unlock/2nd Unlock, Disarm, and Panic. Press and hold
the Unlock button on your keychain transmitter until the siren emits
a long chirp tone. This confirms that programming of channel 2
was successful. Up to 4 transmitters can be programmed, press
and hold the selected button of each additional transmitter until the
chirp tone is heard.
(b) Press and release the valet/override switch 1 time then move onto
step #7 or.
7. Press and release the valet/override switch one time to advance to
channel 3.
8. The dash mounted LED will flash 3 times, and the siren will "chirp"
3 times, indicating that the system is ready to accept programming
for channel 3. Trunk Release Output, (where so equipped), or
alternate channel output when used.
9. (a) Press and hold the Opt. button on your keychain transmitter until the
siren emits a long chirp tone. This confirms that programming of
channel 3 was successful. Up to 4 transmitters can be programmed,
pressandholdtheselectedbuttonofeachadditionaltransmitteruntil
the chirp tone is heard.
(b) Press and hold the 1st Opt. button on your keychain transmitter until
the siren emits a long chirp tone. This confirms that programming of
channel 3 was successful. Up to 4 transmitters can be programmed,
pressandholdtheselectedbuttonofeachadditionaltransmitteruntil
the chirp tone is heard.
128-6105
4 of 6
4
After the desired channel is programmed, turn the ignition key to the off
position to exit programming mode.
VALETSWITCH
Press and Release 3 Times
Press and Release 4 Times
Press and Release 5 Times
Press and Release 6 Times
LED
1 Flash
2 Flashes
3 Flashes
4 Flashes
10. Press and release the valet/override switch one time to advance to
channel4ifsoequipped. Ifyoursystemdoesnothavea4thchannel,
a long chirp followed by a short chirp tone will indicate that the
program mode has been exited.
11. ThedashmountedLED willflash4times andsirenwill"chirp"4times
indicating that the system isready to accept programming of channel 4.
12. (a)Press and hold any combination of two buttons simultaneously, until
the siren emits a long chirp tone. This confirms that programming of
channel 4 was successful. Up to 4 transmitters can be programmed,
pressandholdtheselectedbuttonofeachadditionaltransmitteruntil
the chirp tone is heard.
(b)Press and hold the remaining Opt. button of the transmitter until the
siren emits a long chirp tone. This confirms that programming of
channel4 was successful. Upto4 transmitters canbe programmed,
pressandholdtheselectedbuttonofeachadditionaltransmitteruntil
the chirp tone is heard.
orpress and releasethe push buttonswitch to exitthe programming
mode,
or turn the ignition switch off to exit the programming mode.
The siren emits a long followed by a short chirp tone indicating that the
program mode has been exited.
NOTE: If programming to a Keyless Entry (non alarm) unit, there will be
NO chirp indication.
QUICKREFERENCE:
You can program any individual channel, without reprogramming all
channels, byfollowing the quick referencechart below. (Not All Units Have
4 Channels)
CHANNEL
1
2
3
4
128-6105
5 of 6
5
BATTERYREPLACEMENT:
Thetransmitter incorporates a small red LED visiblethrough thecase. This
LED can be used to indicate battery condition. You will notice a decrease
in transmitter range as the battery condition deteriorates. Transmitter
battery replacement is recommended at least every 10 to 12 months,
depending upon how frequently the transmitter is used.
To replace the battery...
1. Removethetransmittercoverbyremovingthesmallscrewfromtheback
of the transmitter case.
2. Remove the discharged battery, making note of the orientation of the +
and - contacts, and dispose of properly.
3. Install the new (type GP23A) battery, taking care to orient the + and -
contacts properly.
4. Replace the transmitter cover, taking care not to damage the LED or
switches on the circuit board.
128-6105
6 of 6
6
IMPORTANT: To help us expedite your order, please print all of the
information legibly, and mail this form and your payment according to the
instructions below. Please indicate which button pad is used with your
transmitter as indicated above.
Transmitter model number is found on rear case.___________________
1. Name : _________________________________________________
Address : __ ___________________________________________
City : ___________________ State : ______ Zip Code : __________
2. Telephone Number : (________) _____________________________
3. Enter the total number of transmitters required here : _____________
4. The cost per transmitter is $ 65.00.
5. Enter the total amount enclosed here : ________________________
( New York state residents must include the appropriate sales tax. )
6. Method of payment; check one of the boxes below.
Mastercard Visa Check or money order * (do not send cash)
* Make checks payable to Audiovox Corporation
7. Credit Card Number : ______________________________________
8. Credit Card Expiration Date : __________________________
9. Mail this form, and your check, to ;
0133301333
0133301333
01333
6060
6060
60 6161
6161
61
150 . , .. 11788 150 . , .. 11788
150 . , .. 11788 150 . , .. 11788
150 . , .. 11788
: :
: :
:
Credit card purchasers can order additional or replacement
transmitters by phone. Simply dial 1 - 800 - 645 - 4994, and
follow the instructions from the operator interface.
128-6105
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Audiovox Émetteur
Audiovox
Audiovox Prestige 105BP Mode d'emploi
Audiovox
Audiovox ADDP1 Mode d'emploi
Audiovox
Audiovox AX-2K4 Mode d'emploi
Audiovox
Audiovox ACA300 Manuel utilisateur
Audiovox
Audiovox Pursuit 095BPr Mode d'emploi
Audiovox
Audiovox PurSuit 09XR1Pr Mode d'emploi
Audiovox
Audiovox AA-99BT2 Mode d'emploi
Audiovox
Audiovox Prestige 103BP Mode d'emploi
Audiovox
Audiovox Pursuit OE3-FT3 Mode d'emploi
Audiovox
Audiovox PRO-OE3C Guide de dépannage
Audiovox
Audiovox PRO-94FR Mode d'emploi
Audiovox
Audiovox Pursuit PRO-OE3B4 Mode d'emploi
Audiovox
Audiovox 5BCR03A Mode d'emploi
Audiovox
Audiovox PurSuit 08SPr Mode d'emploi
Audiovox
Audiovox Pursuit PRO-OE3 Mode d'emploi
Audiovox
Audiovox Pursuit Series Manuel utilisateur
Audiovox
Audiovox Prestige 101BP Manuel du propriétaire
Audiovox
Audiovox AA-95BT3S Mode d'emploi
Audiovox
Audiovox Prestige APS-2K4 Mode d'emploi
Audiovox
Audiovox PRO94BT3 Mode d'emploi
Manuels Émetteur populaires d'autres marques
Dejero
Dejero EnGo 3x Manuel utilisateur
Rosemount
Rosemount 4600 Manuel utilisateur
Speaka Professional
Speaka Professional 2342740 Manuel utilisateur
trubomat
trubomat GAB 1000 Manuel utilisateur
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manuel utilisateur
Rondish
Rondish UT-11 Manuel utilisateur
