Atmel ATAN0008 Manuel utilisateur

Atmel ATAN0008: ATAK51001 Quick Start Guide

1. Hardware Requirements

The Atmel®ATAK51001 Car Access Reference Design system requires that an

STK600 AVR®development board be acquired SEPARATELY. All of the other hard-

ware components are shipped complete with this kit including power supply and all

connecting cables. The demo can be run in stand-alone mode or with a PC GUI used

to display more information content. The key fob devices come fully configured but

require a CR2032 coin cell battery be acquired SEPARATELY.

1.1 Atmel ATAK51001 Hardware Setup

There are four antennas that must be connected to the RF receiver, LF Basestation,

and LF Driver boards respectively. Three 10-pin ribbon cables connect the Interface

board to the Atmel STK600. Be sure to correctly align the red stripe for “Pin 1” prop-

erly. Power is supplied from a wall transformer and a Y-cable. This powers both the

Atmel ATAK51001 hardware as well as the Atmel STK600.

1.2 Atmel STK600 Hardware Setup

Two 10-pin ribbon cables are used to connect the LEDs and Switches on the Atmel

STK600. The connection to the PC is provided through a USB to Serial convertor.

This requires a 2-pin cable be connected to the UART pins. Simply connect all the

hardware as shown in Figure 1-1 on page 2 by matching the colors.

Atmel

ATAN0008

ApplicationNote

9250A–RKE–11/11

Atmel ATAN0008

Figure 1-1. Hardware Connection

ISP

UART JTAG

PORTE

PORTD

PORTB

9250A–RKE–11/11

Atmel ATAN0008

2. Software Requirements

The Atmel®ATAK51001 devices are shipped with the proper software already loaded. The

Atmel STK600 must be assembled and the Atmel ATmega2560 requires programming for the

system to be fully functional. The Atmel STK600 board must be configured to VTG = 5V. The

STK600 can program its microcontroller via the ISP or JTAG programming headers. The soft-

ware object files can be downloaded from the Atmel website (http://www.atmel.com/dyn/

products/tools_card.asp?tool_id=17382&category_id=154&family_id=692&subfamily_id=

1949) long with the PC GUI executable. When using the PC GUI please make sure the correct

COM port is selected.

Note: After programming the Atmel STK600, individual key fobs must be “Learned” to the system

before use. See Section 2.2 “Support Functions” on page 3.

A more complete explanation of the hardware and software is provided in the official user

guide that can be found on the Atmel website.

2.1 System Operation

The Atmel ATAK51001 provides a complete Car Access Reference System showing three

main functions and three support functions. These three main functions all operate seamlessly

as they would in a real application using correct wireless and wired communication protocols.

Status for all events is shown on the Atmel STK600 LEDs and the PC GUI main screen. The

PC GUI also includes auditory feedback as well as additional view boxes showing the content

of the various messages.

• (RKE) Remote Keyless Entry

• (PEPS) Passive Entry Passive Start

• (IMM) Immobilizer

2.2 Support Functions

Before use each individual key fob must be paired to the vehicle controller. This is made pos-

sible through the “Learn” modes. There are three modes:

• RF - One way transfer of the RKE/PEPS secret key from the fob to the vehicle

• IMMO - Two way programming of new randomly generated secret keys from the vehicle

into the fob for use in both RKE/PEPS and IMM modes

• Clear - Erases all previously learned key fobs

It is possible to associate up to 8 key fobs with this system. The sequence of operation is as

follows

2.3 RKE Learn

1. Press SW5 on STK600 (LED5 should turn ON)

2. Press S3 on key fob (within 10s, while LED5 remains ON)

3. LED5 on Atmel STK600 should blink once. (PC GUI should show a “graduation cap”

icon)

4. Press SW5 to exit if finished or wait 10s

9250A–RKE–11/11

Atmel ATAN0008

2.4 Immobilizer Learn

1. Place key fob immobilizer coil within 2cm of basestation coil

2. Press SW4 on Atmel®STK600

3. LED5 on Atmel STK600 should blink once. (PC GUI should show a “graduation cap”

icon)

2.5 RKE Operation

RKE is the most basic mode of wireless car access and consists of pressing a button on a key

fob to lock/unlock the vehicle. The following sequence shows this functionality.

1. Press SW1 (LOCK) or SW2 (UNLOCK) on the key fob

2. LED4 <-- --> LED0 on the Atmel STK600 should cycle left or right respectively if the

AES encryption is valid. All other LEDs should be off. (PC GUI should show a Locked

or Unlocked icon and corresponding sound)

2.6 PEPS Operation

PEPS is currently used only on the high-end car access systems and allows the driver to keep

the key fob in their pocket or purse. The user does not need to directly interact with the key fob

to enter/exit or start the vehicle. We show three different sequences of operation for this func-

tionality that are as follows.

2.7 PEPS Unlock

1. Put the key fob within range of the vehicle system (typically 1m)

2. Press SW7 on Atmel STK600

3. LED7 on Atmel STK600 should turn ON and LED4 ? LED0on the STK600 should

cycle left if the AES encryption is valid. (PC GUI should show an Unlocked icon,

green Key Fob, and corresponding sound)

2.8 PEPS Lock (Key Forgotten Inside Vehicle)

1. Put the key fob within range of the vehicle system (typically 1m)

2. Press SW6 on Atmel STK600

3. LED7 on Atmel STK600 should turn ON and LED4 <-- LED0 on the Atmel STK600

should cycle right if the AES encryption is valid. (PC GUI should show an Unlocked

icon, red Key Fob, and corresponding sound)

2.9 PEPS Lock (Key Removed from Vehicle)

1. Put the key fob within range of the vehicle system (typically 3m)

2. Press SW6 on Atmel STK600

3. No change on Atmel STK600 (PC GUI should show an Locked icon and correspond-

ing sound)

9250A–RKE–11/11

Atmel ATAN0008

2.10 PEPS Start

1. Put the key fob within range of the vehicle system (typically 1m)

2. Press SW0 on Atmel®STK600

3. LED7 on Atmel STK600 should turn ON and LED4 --> LED0 on the Atmel STK600

should cycle right if the AES encryption is valid. (PC GUI should show an Start icon,

green Key Fob, and corresponding sound)

Note: For backup starting where the key fob battery is dead or removed, see step 1 and 3 of the

immobilizer operation.

2.11 Immobilizer Operation

The immobilizer is used to protect the vehicle from starting except when authorized by a valid

user. This can be done with a stand-alone transponder all the way up to the full PEPS system

(Dead battery mode). In order to show just this function there is a special mode built in to the

system.

1. Put the key fob immobilizer coil next to vehicle basestation coil (typically 2cm)

2. Press SW1 on Atmel STK600

3. LED6 on Atmel STK600 should turn ON and LED4 <-- LED0 on the STK600 should

cycle left if the AES encryption is valid. (PC GUI should show an Start icon, Immobi-

lizer Icon, and corresponding sound)

9250A–RKE–11/11

Atmel ATAN0008

Place STK600 Here

Switches LEDs

PORTK PORTC

RS232

TXD Qprox Door Handle

PH1 PortJ

LEDs

PEPS Immo Learn AES Success <———

Passive Entry Learn Modes Immo

Start

Passive

Start

Buttons

UNLOCK LOCK RF IMMO CLEAR <———

Atmel Corporation

2325 Orchard Parkway

San Jose, CA 95131

USA

Tel: (+1)(408) 441-0311

Fax: (+1)(408) 487-2600

Atmel Asia Limited

Unit 01-5 & 16, 19/F

BEA Tower, Millennium City 5

418 Kwun Tong Road

Kwun Tong, Kowloon

HONG KONG

Tel: (+852) 2245-6100

Fax: (+852) 2722-1369

Atmel Munich GmbH

Business Campus

Parkring 4

D-85748 Garching b. Munich

GERMANY

Tel: (+49) 89-31970-0

Fax: (+49) 89-3194621

Atmel Japan

9F, Tonetsu Shinkawa Bldg.

1-24-8 Shinkawa

Chuo-ku, Tokyo 104-0033

JAPAN

Tel: (+81) (3) 3523-3551

Fax: (+81) (3) 3523-7581

Atmel®, Atmel logo and combinations thereof, AVR®, STK®and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries.

Other terms and product names may be trademarks of others.

Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellec-

tual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS

OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY

WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICU-

LAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR

INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION)

ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel

makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to

specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specif-

ically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or war-

ranted for use as components in applications intended to support or sustain life.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Atmel Matériel informatique

Atmel

Atmel RCB256RFR2 Instructions d'utilisation

Atmel

Atmel ATF16V8B Manuel utilisateur

Atmel

Atmel AT85DVK-07 Manuel utilisateur

Atmel

Atmel 8-bit AVR Microcontrollers AVR430: MC300 Manuel utilisateur

Atmel

Atmel 7698AAUTO01/07 Manuel utilisateur

Atmel

Atmel ATDH2200E Manuel utilisateur

Atmel

Atmel AVR XMEGA 8/16-bit High Performance Low Power Flash... Manuel utilisateur

Atmel

Atmel AT91SAM7L-STK Manuel utilisateur

Atmel

Atmel ATWINC1500 Manuel utilisateur

Atmel

Atmel STK501 Manuel utilisateur

Atmel

Atmel REB233-XPRO Manuel utilisateur

Atmel

Atmel FPSLIC AT94KAL Series Manuel utilisateur

Atmel

Atmel AT86RF211 Manuel utilisateur

Atmel

Atmel AT76C502A Manuel utilisateur

Atmel

Atmel AVR364 Manuel utilisateur

Atmel

Atmel AT24C16C Manuel utilisateur

Atmel

Atmel SAM9X25 Manuel utilisateur

Atmel

Atmel AT73C246-EK1 Manuel utilisateur

Atmel

Atmel ATSAMD21BLDC24V-STK Manuel utilisateur

Atmel

Atmel ATAK2270 Manuel utilisateur

Atmel

Atmel Dual Triple DMOS Output Drivers with Serial Input and PWM Control... Manuel utilisateur

Atmel

Atmel FPSLIC ATSTK94 Manuel utilisateur

Atmel

Atmel FingerChip FCDEMO4 Instructions d'installation et d'utilisation

Atmel

Atmel ATAB-SPI-LPT Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur