ARTHUR HOLM DB2Twin Manuel utilisateur
Mounting Instructions DB2 & DB1Twin
AHDB2DOC01
- Mounting Guide Pg. 2-8
- Veneer Guide (Optional) Pg.9-15
Information
The DB2 and DB1Twin monitors are designed to be mounted from below
the table. Included in this version are all necessary brackets.
INTRODUCTION
2
ATTENTION
Manipulation of the product should be avoided, no stress should be applied to the product except from the
instructions given in this document. Cutting, drilling, soldering, adding of electrical and mechanical
components can cause danger and should be avoided by all mean. Not complying with these direction will
result in a lost of the Arthur Holm warranty. Albiral Display Solution S.L. shall not be held liable for any loss
or injury incurred as a result of modifications made to goods by anyone other than the supplier or the
supplier's authorised representative without the supplier's written permission. Such modifications shall be
deemed to terminate any further guarantee obligations. Compensation will not be paid for wages, loss of
profit, waste of time, packing and transport or any financial liability resulting from defects in the goods.
(Albiral Display Solutions shall not be liable for any loss or injury caused by negligence.)
PATTERN HOLE
Pattern hole dimensions for milling are specified in the corresponding drawing.
The milling of the furniture has to be done from bellow.
Mounting table brackets
Table Bracket
“A”
Front Side
Mount the table brackets below the table using the holes indicated on the corresponding Pattern
Hole drawing. The screws (x6) are not supplied; The weight of the monitor is up to 25Kg.
PAY ATTENTION THAT THE BRACKETS ARE MOUNTED IN THEIR CORRESPONING SIDE
Front Side
3
View from below the table
Table Bracket
“B”
View from below the table
Mounting the monitor brackets
Mount the monitor brackets on their corresponding side using the supplied screws
Mount the vertical adjustment screws (2+2) on to the monitor bracket so that the tip of the screw is flushed with
the upper side of the monitor bracket.
4
(x4) Vertical Adjustment
Screws
Right Monitor bracket
“1”
Left Monitor bracket
“2” Front Side
(X4 Screw M6x20)
(X4 washer)
Checking assembly
Dimensions A and B in table brackets and in monitor brackets must be the same (+ 1mm).
If adjustment is necessary loosen 3+3 Table bracket screws, keeping always symmetry regarding to the
monitor hole in the table. Subsequently, tighten the table bracket screws.
Front Side
View from below the
table
View from above the
monitor
5
Front Side
Hanging the monitor
Mount 2+2 nuts on to both table
brackets as indicated on the
drawing.
Hang the monitor above nuts
6
Front Side
Centring the monitor
Air gap around the monitor have
to be 2mm [0,08]. Otherwise the
monitor could come in contact
with the table while opening and
be damaged
Tighten each nut gradually until
the monitor surface is levelled with
the table surface.
Front Side
View from above the
table
7
Front Side
Fine centring of the monitor
For adjusting the monitor closer or
further away from the table edge
loosen the four nuts half a turn
and move the monitor. When the
monitor is centred tighten the four
nuts.
IMPORTANT:
To secure the monitor tighten the four vertical adjustment screws.
Front Side
For adjusting the monitor to the
left or right loosen the table
screws half a turn and centre the
monitor. When the monitor is
centred tighten the six screws.
8
In case fine centering of the monitor is necessary
View from below the table
Veneer Guide (Optional)
The DB2 and DB1Twin monitors are available in a special version that is
prepared to be mounted from below the table with a Veneer finishing on the
top of the monitor to match the table. The Veneer is not supplied.
The Veneer option (V1, V2, V3) are available under request.
The Veneer can be placed in three ways:
VENEER
INTRODUCTION
9
Veneer: The veneer thickness must be
5mm [0.19]. A mechanized blind hole
will be necessary to hide the touch
button copper cylinder.
Veneer + Distance Plate: For Veneers
Thickness of 1mm [0,04] or less. It will be
necessary a Distance Plate to hide the
touch button copper cylinder.
Veneer
Distance Plate
Option2: DB2 V2 Option3: DB2 V3
Option1: DB2 V1
Veneer
Veneer
10
OPTION 1
- Double-side tape or glue used can’t be thicker than 0,2-0,25mm [0.008-0.01]
2. Clean the top surface of the metal monitor housing and the
bottom surface of the Veneer.
3. Glue the Veneer. Double-side tape or glue can be used
(depending on the kind of materials are going to be jointed).
1. Check if the Veneer fits perfectly with the monitor. To join both parts correctly it is important that the two surfaces
are touching each other in the whole length. (To make easier the adjustment the hight of the touch button can be
barely adjusted.)
The pressure applied
must not exceed 1 Kg
evenly distributed on
monitor surface.
Veneer Guide (Optional)
Ce manuel convient aux modèles suivants
1
Autres manuels ARTHUR HOLM Moniteur
ARTHUR HOLM
ARTHUR HOLM AH17D X2HDGA Manuel utilisateur
ARTHUR HOLM
ARTHUR HOLM Dynamic 3 Manuel utilisateur
ARTHUR HOLM
ARTHUR HOLM AH24DB2 Manuel utilisateur
ARTHUR HOLM
ARTHUR HOLM Dynamic2 AH12D216A Manuel utilisateur
ARTHUR HOLM
ARTHUR HOLM AH24D Manuel utilisateur
ARTHUR HOLM
ARTHUR HOLM RISE AH10 RA Manuel utilisateur
ARTHUR HOLM
ARTHUR HOLM Dynamic3Talk Manuel utilisateur
ARTHUR HOLM
ARTHUR HOLM AH15D X2HDA Manuel utilisateur
ARTHUR HOLM
ARTHUR HOLM DB2Share Manuel utilisateur
ARTHUR HOLM
ARTHUR HOLM AH17S HDGA Manuel utilisateur
ARTHUR HOLM
ARTHUR HOLM D1Twin Manuel utilisateur
ARTHUR HOLM
ARTHUR HOLM AH15DCDHD Manuel utilisateur
ARTHUR HOLM
ARTHUR HOLM DynamicX2KM Manuel utilisateur
ARTHUR HOLM
ARTHUR HOLM RISE AH12RI Wide Manuel utilisateur
ARTHUR HOLM
ARTHUR HOLM DynamicX2Talk Manuel utilisateur
ARTHUR HOLM
ARTHUR HOLM RISE AH12RI Wide Manuel utilisateur
ARTHUR HOLM
ARTHUR HOLM AH10 DA Manuel utilisateur
ARTHUR HOLM
ARTHUR HOLM AH19D X2HDGA Manuel utilisateur
ARTHUR HOLM
ARTHUR HOLM AH10DB2 Manuel utilisateur
ARTHUR HOLM
ARTHUR HOLM AH22DRM Manuel utilisateur
