ARTHUR HOLM Dynamic 3 Manuel utilisateur

Assembling guide Dynamic 3 + DTalk

Information

Dynamic 3 monitor is available in a special version prepared to be

assembled with DynamicTalk device. This special version is supplied

with all accessories to be assembled.

DynamicTalk can be assembled at the right side, at left side or at both

sides. This guide shows how to assemble it at left side (the assembling

at the right side follows the same process).

INTRODUCTION

Manipulation of the product should be avoided, no stress should be applied to the product except from

the instructions given in this document. Cutting, drilling, soldering, adding of electrical and mechanical

components can cause danger and should be avoided by all mean. Not complying with these direction

will result in a lost of the Arthur Holm warranty. Albiral Display Solution S.L. shall not be held liable for

any loss or injury incurred as a result of modifications made to goods by anyone other than the supplier

or the supplier's authorised representative without the supplier's written permission. Such

modifications shall be deemed to terminate any further guarantee obligations. Compensation will not be

paid for wages, loss of profit, waste of time, packing and transport or any financial liability resulting

from defects in the goods. (Albiral Display Solutions shall not be liable for any loss or injury caused by

negligence.)

PATTERN HOLE

Pattern hole dimensions for milling are specified in the general dimensions for each reference.

ATTENTION

Preparing the assemble

(x2) DIN 9021 4,3

•Being D3 mounted on the table: Mount the (x2)

washers and the (x2) wing nuts supplied at the bolts

shown. Screw the wing nuts until they are flushed with

the end of the bolt.

(x2) DIN 315 M4

Flush bolt

View from below

the table

View from below

the table

Assembling DynamicTalk 4

•Insert DynamicTalk in the indicated position.

The top plate must be just above the washers

•Turn DynamicTalk until the two open holes

on the top plate are in contact with the bolts

Assembling DynamicTalk

•Push carefully the DynamicTalk upward, please

take care with the hatch of the cover plate.

•There is a guide bolt that has to enter into the

hole of the top plate

•Keeping pressed up the DynamicTalk, screw

the wing nuts with the finger.

Assembling DynamicTalk

•Enter the mounting plate through the DynamicTalk.

•If Dynamic talk has a cable to connect the

microphone: pass the Microphone cable + connector

trough the mounting plate hole.

Assembling DynamicTalk (STANDARD & BOSCH)

•Fix the DynamicTalk to the mounting plate

(x2) DIN 6798 5,3

(x2) DIN 7985 M5x12

Follow This step for standard DynamicTalk or

DynamicTalk with BOSCH

•Fix the mounting plate with washers and screws provided.

(x4) DIN 6798 5,3

(x4) DIN 7985 M5x10

Assembling DynamicTalk (DIS)

•Fix the DynamicTalk to the mounting plate

(x2) DIN 6798 5,3

(x2) DIN 7985 M5x12

Follow This step for DynamicTalk with DIS

or TELEVIC microphone.

•Fix the mounting plate with washers and screws provided.

(x4) DIN 6798 5,3

(x4) DIN 7985 M5x10

Connect XLR connector from the DynamicTalk

to the socket (Microphone IN)

www.arthurholm.com

Ce manuel convient aux modèles suivants

Autres manuels ARTHUR HOLM Moniteur

ARTHUR HOLM

ARTHUR HOLM Dynamic3 AH15D3HDGA Manuel utilisateur

ARTHUR HOLM

ARTHUR HOLM AH1 Series Manuel utilisateur

ARTHUR HOLM

ARTHUR HOLM AH15DCDHD Manuel utilisateur

ARTHUR HOLM

ARTHUR HOLM AH10DB2 Manuel utilisateur

ARTHUR HOLM

ARTHUR HOLM AH17D3 RHDGA TALK Manuel utilisateur

ARTHUR HOLM

ARTHUR HOLM AH12TX16GA Manuel utilisateur

ARTHUR HOLM

ARTHUR HOLM AH1 Series Manuel utilisateur

ARTHUR HOLM

ARTHUR HOLM Dynamic 1H Manuel utilisateur

ARTHUR HOLM

ARTHUR HOLM AH12D 216A Manuel utilisateur

ARTHUR HOLM

ARTHUR HOLM AH15D3 HDGA Manuel utilisateur

ARTHUR HOLM

ARTHUR HOLM Dynamic3Reverse Manuel utilisateur

ARTHUR HOLM

ARTHUR HOLM AH15D X2HDA Manuel utilisateur

ARTHUR HOLM

ARTHUR HOLM RISE AH10 RA Manuel utilisateur

ARTHUR HOLM

ARTHUR HOLM DynamicX2Talk Manuel utilisateur

ARTHUR HOLM

ARTHUR HOLM AH15D X2HDGA Manuel utilisateur

ARTHUR HOLM

ARTHUR HOLM DB2 Series Manuel utilisateur

ARTHUR HOLM

ARTHUR HOLM DB2Share Manuel utilisateur

ARTHUR HOLM

ARTHUR HOLM D1Twin Manuel utilisateur

ARTHUR HOLM

ARTHUR HOLM Gooseneck AH22NTT16 Manuel utilisateur

ARTHUR HOLM

ARTHUR HOLM AH17D1HDA2F Manuel utilisateur

ARTHUR HOLM

ARTHUR HOLM AH24DB2 Manuel utilisateur

ARTHUR HOLM

ARTHUR HOLM AH17 NTTHD Manuel utilisateur

ARTHUR HOLM

ARTHUR HOLM DynamicX2KM Manuel utilisateur

ARTHUR HOLM

ARTHUR HOLM AH12D1HGA Manuel utilisateur

Manuels Moniteur populaires d'autres marques

Linear Acoustic

Linear Acoustic LQ-1000 Manuel utilisateur

AOC

AOC I2579V Manuel utilisateur

Gateway

Gateway FPD1520 Manuel utilisateur

Furuno

Furuno Mu 120c Manuel utilisateur

Asus

Asus VB171D - 17" LCD Monitor Manuel utilisateur

Dell

Dell S2230MX Instructions d'utilisation

Philips

Philips 107C64 Manuel utilisateur

Dell

Dell S2409WFP Manuel utilisateur

EverFocus

EverFocus EN-7517E Manuel utilisateur

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuel utilisateur

Dell

Dell Precision 7680 Mode d’emploi

LG 50PM1M - - 50" Plasma Panel Manuel utilisateur

Bosch

Bosch DDU 9 Manuel utilisateur

Acer

Acer A231HL Manuel utilisateur

Philips

Philips 86BDL4152T Manuel utilisateur

NEC

NEC AccuSync LCD5V Manuel utilisateur

Emay

Emay SleepO2 Manuel utilisateur

IBM

IBM 6360 Instructions d'installation