AOpen AK77-600GN Fiche technique

SYSFAN2 Connector

IrDA Connector

Front Panel Connector

FDD

onnecto

USB 2.0 Connecto

sx2

JP14 CMOS Clear Jumper

2Mb Flash ROM BIOS

Resetable Fuse

462-pin CPU Socket with Voltage and

Frequency Auto-Detection that supports

AMDTMAthlonTM / DuronTM / and AthlonTMXP

(with CPU Overheat Protection circuit to

AthlonTMXP CPU onl

CPUFAN Connecto

184-pin DIMMsx3 supports

DDR 266/333/400 (Max to 3GB)

VIA

Apollo KT600 / VT8237 Chipsets

3300μF Low ESR Capacitors

ATX Power Connector

CD-IN Connector

Onboard AC’97 CODEC

Case Open Connector

Front Audio Connector

JP28 Keyboard/Mouse Wakeup Jumpe

SYSFAN1 Connector

Realtek LAN Chip

8X AGP slot

AUX-IN Connector

GAME Port Connector

LAN

onnecto

ATA 66/100/133 IDE Connectors x2

STBY LED

AOpen reserves the right to revise all the specifications and information contained in this documentation, which are subject to change without notice.

32-bit PCI Expansion Slots x5

Line-In

Speaker Out

MIC-In

PS/2 Mouse

Connecto

SPP/EPP/ECP Parallel Port RJ45 LAN Jack

PS/2 Keyboard

Connecto

USB Ports

COM 1 Port COM 2 Port

USB Ports

JP21 K7 Host Clock Select Jum

SATA

onnectorsx

S/PDIF Connector

1. JP14 Clear CMOS

Everything you need to boot this

motherboard is included in this

Easy Installation Guide. For more

information, a complete Online

User's Manual can be found in the

Bonus Pack CD Disc. Thanks for

the help of saving our earth.

PART NO: 49.8A706.EE4 DOC. NO: AK77600GN-EG-E0312D

You can clear CMOS to restore system default setting. To

clear the CMOS, follow the procedure below.

1. Turn off the system and unplug the AC power.

2. Remove ATX power cable from connector PWR2.

3. Locate JP14 and short pins 2-3 for a few seconds.

4. Return JP14 to its normal setting by shorting pin 1 & pin 2.

5. Connect ATX power cable back to connector PWR2.

Tip: When should I Clear CMOS?

1. Boot fails because of overclocking…

2. Forget password…

3. Troubleshooting…

Motherboard x1

Easy Installation Guide x1

80-wire IDE Cable x1

Floppy Disk Drive Cable x1

SerialATACablex1

IO Shield x 1

Bonus Pack CD x1

VIA SATA RAID Driver Diskette x 1

Pin 1

2. JP28 Keyboard/Mouse Wake-up Enable/Disable Jumper

This motherboard provides keyboard / mouse wake-up function. You can use JP28 to enable or disable this

function, which could resume your system from suspend mode with keyboard or mouse installed. The factory

default setting is set to “Disable” (1-2), and you may enable this function by setting the jumper to 2-3.

JP28

KB/Mouse Wake-up

Pin 1

Normal

(

default

)

Clear CMOS

Enable

Disable

(Default)

Plug in the CPU fan cable to the 3-pin CPUFAN connector. If you have chassis fan, you

can also plug it on SYSFAN1 or SYSFAN2 connector.

The ATX power supply uses a 20-pin connector shown below. Make sure you plug in the

right direction.

CPU Ratio From 5.0x to 18x step 0.5x

CPU FSB 100-248MHz

CPU CPU Core

Frequency

EV6 Bus

Clock Ratio

Athlon 1.33G 1.33GHz 266MHz 10.0x

Athlon 1.4G 1.4GHz 266MHz 10.5x

AthlonXP 1500+ 1.3GHz 266MHz 10.0x

AthlonXP 1600+ 1.4GHz 266MHz 10.5x

AthlonXP 1700+ 1.46GHz 266MHz 11.0x

AthlonXP 1800+ 1.53GHz 266MHz 11.5x

AthlonXP 1900+ 1.6GHz 266MHz 12.0x

AthlonXP 2000+ 1.667GHz 266MHz 12.5x

AthlonXP 2100+ 1.73GHz 266MHz 13x

AthlonXP 2200+ 1.80GHz 266MHz 13.5x

AthlonXP 2400+ 2.0GHz 266MHz 15x

AthlonXP2500+ (Barton) 1.833GHz 333MHz 11x

AthlonXP 2600+ 2.13GHz 266MHz 16x

AthlonXP 2600+ 2.08GHz 333MHz 12.5x

AthlonXP 2700+ 2.16GHz 333MHz 13x

AthlonXP 2600+ (Barton) 1.917GHz 333MHz 11.5x

AthlonXP 2800+ (Barton) 2.083GHz 333MHz 12.5x

AthlonXP 3000+ (Barton) 2.167GHz 333MHz 13x

AthlonXP 3000+ (Barton) 2.100GHz 400MHz 10.5x

AthlonXP 3200+ (Barton) 2.2GHz 400MHz 11x

Note: With CPU speed changing rapidly, there might be fastest CPU on the

market by the time you received this installation guide. This table is kindly for

your references only.

5. Setting CPU Voltage & Frequency

CPU Core Voltage Auto Detectable

This motherboard supports CPU VID function. The CPU core voltage will be automatically

detected and it is not necessary to set CPU Core Voltage.

Setting CPU Frequency

This motherboard is CPU jumper-less design, you can set CPU frequency through the BIOS

setup, and no jumpers or switches are needed.

BIOS Setup > Frequency / Voltage Control > CPU Bus Frequency

Core Frequency = CPU FSB Clock * CPU Ratio

Warning: Supposed you

have had adjusted CPU

ratio on your current CPU,

and you plan to replace it

with a new CPU. Please

use <Home> key or Clear

CMOS to restore the

default setting after

reinstalling a new CPU.

Note: Some CPU fans do not have

sensor pin so they cannot support fan

monitoring.

CPUFAN Connector

4. Installing CPU & System Fan

SYSFAN1 Connector

SYSFAN2 Connector

GND

+12V

SENSOR

3. Connecting ATX Power Connector

GND

+12V

SENSOR

GND

+12V

SENSOR

Note:VIA®Apollo KT600 chipset supports 266/333/400MHz FSB with

performance reaches maximum 400MHz EV6 system bus and supports 66MHz

AGP clock, higher clock setting may cause serious system damage.

Tip: If your system hangs

or fails to boot because of

overclocking, simply use

<Home> key to restore the

default setting or you can

wait till the AOpen “Watch

Dog ABS” reset the system

in five seconds and system

will auto-detect hardware

again.

8. S/PDIF Connector

S/PDIF (Sony/Philips Digital Interface) is a newest audio transfer file format, which provides

impressive audio quality through optical fiber and allows you to enjoy digital audio instead of analog

audio. Through a specific audio cable, you can connect the S/PDIF connector to other end of the

S/PDIF audio module, which bears S/PDIF digital output. Normally there are two S/PDIF outputs as

shown, one for RCA connector, the most common one used for consumer audio products, and the

other for optical connector with better audio quality. Same as outputs, you can also connect RCA or

optical audio products to input connectors on the module and have the voice or music come out from

your computer. However, you must have a S/PDIF supported speaker/amplifier/decoder with S/PDIF

digital input/output to connect to the S/PDIF digital input/output to make the most out of this function.

This motherboard comes with an ALC650F CODEC, which supports high quality of 5.1

Channel audio effects, bringing you a brand new audio experience. On the strength of the

innovative design of ALC650F, you're able to use standard line-jacks for surround audio

output without connecting any external module. To apply this function, you have to install the

audio driver in the Bonus Pack CD as well as an audio application supporting 5.1 Channel.

Picture bellow represents the standard location of all speakers in 5.1Channel sound track.

Please connect the plug of your front speakers to the green “Speaker out” port, rear

speakers’ plug to the blue “Line in” port and both of the center and subwoofer speakers to

the red “MIC in” port.

USB 2.0 Connector

9. Super 5.1 Channel Audio Effects

6. JP21 K7 Host Clock Selection

7. Support Eight USB 2.0 Ports

+5V

SBD7-

SBD7+

GND

+5V

SBD6-

SBD6+

GND

KEY

USB 2.0 Connector

This jumper is used to specify the relationship of PCI and FSB clock. Generally speaking, if

you are not an over-clocker, we recommend you to set it to the default setting. Additionally,

this motherboard also provides “1MHz Stepping Adjustment” feature for overclockers to

adjust CPU FSB frequency via BIOS setup program. If you fix the CPU FSB frequency by

JP21, the “1MHz Stepping Adjustment” range will be changed according to what type of

CPU you use.

JP21 K7 Host Clock

Select Jum

This motherboard provides eight USB 2.0 ports. Compared to traditional USB 1.0

1.1 with

the speed of 12Mbps, USB 2.0 has a fancy speed up to 480Mbps, which is 40 times faster

than the traditional one.

Pin 1

100MHz

Auto detect

(

default

)

S/PDIF Module

(User Upgrade Optional)

S/PDIF

Cable

S/PDIF OUT

S/PDIF IN

(RCA)

S/PDIF IN

(

tical

)

S/PDIF OUT

1+5V

SPDIFOUT

GND

SPDIFIN

Pin 1

10. Connecting Front Panel Cable

Attach the power LED, speaker, and reset switch connectors to

the corresponding pins. If you enable “Suspend Mode” item in

BIOS Setup, the ACPI & Power LED will keep flashing while the

system is in suspend mode.

Locate the power switch cable from your ATX housing. It is

2-pin female connector from the housing front panel. Plug this

connector to the soft-power switch connector marked SPWR.

11. Connecting Serial ATA Disk

12. Front Audio Connector

13. Support 10/100 Mbps LAN onboard

On the strength of Realtek 8101L LAN controller on board, this motherboard provides

10/100 Mbps Ethernet for office and home use. The Ethernet RJ45 connector is located

on top of USB connectors. The orange LED indicates the link mode, it lights when linking

to network. The green LED indicates the transfer mode and it lights when data is

transferring in 100 Mbps. To enable or disable this function, you may simply adjust it

through BIOS.

If the housing has been designed with an audio port on the front panel, you’ll be able to

connect onboard audio to front panel through this connector. By the way, please remove

5-6 and 9-10 jumper caps from the Front Audio Connector before connecting the cable.

Please do not remove these 5-6 and 9-10 yellow jumper caps if there’s no audio port on

the front panel.

Pin 1

AUD_GND

AUD_VCC

AUD_RET_R

KEY

AUD_RET_L

AUD_MIC

AUD_MIC_BIAS

AUD_FPOUT_R

AUD_FPOUT_L

Front Audio Connector

To connect a Serial ATA disk, you have to have a 7-pin serial ATA cable. Connect two ends

of the serial ATA cable to the serial ATA header on the motherboard and the disk. Like

every other traditional disk, you also have to connect a power cable. Please be noted that

it is a jumper free implement; you don’t need to set jumpers to define a master or slave

disk. When connecting two serial ATA disks, the system will automatically take the one

connected to “Serial ATA 1” header as a master disk.

Orange/Link

Green/Transfer

SPEAKER

IDE LED

Power Switch

ACPI & Power LED

RESET

SPWR

GND

ACPILED-

GND

ACPILED+

GND

RESET

GND

+5V

IDE LED

+5V

GND

SPEAKER

SATA port 2SATA port 1

After you finish the setting of jumpers and connect correct cables. Power on

and enter the BIOS Setup, press <Del> during POST (Power On Self Test).

Choose "Load Setup Defaults" for recommended optimal performance.

Warning: The upgrade of new BIOS will permanently replace your original BIOS

content after flashing. The original BIOS setting and system PnP information will be

refreshed and you probably need to re-configure your system.

14. AOpen Bonus Pack CD

15. Power-on and Load BIOS Setup 17. BIOS Upgrade under Windows Environment

You may accomplish BIOS upgrade procedure with EzWinFlash by the following steps,

and it’s STRONGLY RECOMMENDED to close all the applications before you start the

upgrading.

1. Download the new version of BIOS package zip file from AOpen official web site.

(ex: http://english.aopen.com.tw)

2. Unzip the download BIOS package (ex: WAK77600GN102.ZIP) with WinZip

(http://www.winzip.com) in Windows environment.

3. Save the unzipped files into a folder, for example, WAK77600GN102.EXE &

WAK77600GN102.BIN.

4. Double click on the WAK77600GN102.EXE; EzWinFlash will detect the model name

and BIOS version of your motherboard. If you had got the wrong BIOS, you will not

be allowed to proceed with the flash steps.

5. You may select preferred language in the main menu, then click [Start Flash] to start

the BIOS upgrade procedure.

6. EzWinFlash will complete all the process automatically, and a dialogue box will pop

up to ask you to restart Windows. You may click [YES] to reboot Windows.

7. Press <Del> at POST to enter BIOS setup, choose "Load Setup Defaults", then

“Save & Exit Setup”. Done!

16. Installing VIA 4 in 1 Driver

You can use the autorun menu of Bonus CD disc. Choose the utility and driver and select

model name.

Del

Warning: Please avoid of using "Load

Turbo Defaults", unless you are sure

your system components (CPU, DRAM,

HDD, etc.) are good enough for turbo

settin

You can install the VIA 4 in 1 driver (IDE Bus master (For Windows NT use), VIA ATAPI

Vendor Support Driver, VIA AGP, IRQ Routing Driver (For Windows 98 use), VIA Registry

(INF) Driver) from the Bonus Pack CD disc auto-run menu.

Warning: To take advantage of ATA133, it is a must to install the latest version of VIA

4in1 driver in the Bonus CD.

For Windows2000, it cannot support ATA133 even after installing the latest version of

VIA 4

1 driver until the new release of Service

Pack 3 from Microsoft.

If you encounter any trouble to boot you system, follow the procedures

accordingly to resolve the problem.

Part Number and Serial Number

The Part Number and Serial number are printed on bar code label. You can find this bar

code label on the outside packing, or on component side of PCB. For example:

Model name and BIOS version

AK77-600GN R1.00 Aug. 01. 2003 AOpen Inc.

Award Plug and Play BIOS Extension v1.0A

Model name and BIOS version can be found on upper left corner of first boot screen

(POST screen). For example:

AK77-600GN is model name of motherboard; R1.00 is BIOS version

P/N: 91.88110.201 is part number, S/N: 91949378KN73 is serial number.

Part No. Serial No.

Make sure if the jumper settings for CPU and DRAMs are correct.

Clear CMOS, then plug the ATX power cord correctly.

(For P4 system, please also plug the 4pin(+12V) cord.

Install the VGA card. Then connect your monitor and keyboard.

The problem was probably caused

by power supply or motherboard

failure. Please contact your reseller

or local distributor for repairing.

Perhaps your VGA card or monitor

is defective.

Yes

It is very possible that your keyboard

is defective.

During system rebooting, press Del to enter BIOS Setup. Choose

“Load Setup Default".

The problem should be caused by the

IDE cables or HDD itself.

Re-install Windows 95, Windows 98 or Windows NT.

Yes

Turn off the power and unplug the AC power cable, then remove all

of the addon cards and cables, including VGA, IDE, FDD, COM1,

COM2 and Printer.

Turn on the power, and check if

the power supply and CPU fan

work properly.

Start

Check if there is display.

Press Ctrl, and Alt key at the

same time, hold them and then

press Del to see if the

stem reboots.

Turn off the system and

re-connect the IDE cable.

Check if the system can

reboot successfully.

End

Dear Customer,

Thanks for choosing AOpen products. To provide the best and fastest service to

our customer is our first priority. However, we receive numerous emails and

phone-calls worldwide everyday; it is very hard for us to serve everyone on time.

We recommend you to follow the procedures below and seek help before

contacting us. With your help, we can then continue to provide the best quality

service to more customers.

Thanks very much for your understanding!

AOpen Technical Supporting Team

Web Site: http://www.aopen.com.tw

E-mail: Send us email by going through the contact form below.

English http://english.aopen.com.tw/tech/default.htm

Japanese http://www.aopen.co.jp/tech/default.htm

Chinese http://www.aopen.com.tw/tech/default.htm

German http://www.aopencom.de/tech/default.htm

Simplified Chinese http://www.aopen.com.cn/tech/default.htm

Pacific Rim

AOpen Inc.

Tel: 886-2-3789-5888

Fax: 886-2-3789-5899

Europe

AOpen Computer b.v.

Tel: 31-73-645-9516

Email: [email protected]

Germany

AOpen Computer GmbH.

Tel: 49-2131-1243-710

Fax: 49-2131-1243-999

China

艾爾鵬國際貿易(上海)有限公司

Tel: 86-21-6225-8622

Fax: 86-21-6225-7926

Japan

AOpen Japan Inc.

Tel: 81-048-290-1800

Fax: 81-048-290-1820

America

AOpen America Inc.

Tel: 1-408-232-1200

Fax: 1-408-232-1280

Online Manual: To download manual, please log on and then select your

preferred language. Under “Type” directory, choose “Manuals” to go to our

manual database. You can also find the manual and EIG in AOpen Bonus Pack.

http://download.aopen.com.tw/downloads

Test Report: We recommend you to choose board/card/device from the

compatibility test reports for assembling your PC. It may prevent incompatibility

problems.

http://english.aopen.com.tw/tech/report/default.htm

FAQ: Here we list problems that users often encounter and FAQ

(Frequently Asked Questions). You may select your preferred language

after log on, and may be able to find a solution to your problem.

http://club.aopen.com.tw/faq/

Download Software: After log on and having language selected, you may

get the latest updated BIOS/utility and drivers you need under “Type”

directory. In most case, newer versions of drivers and BIOS have solved

earlier bugs or compatibility problems.

http://download.aopen.com.tw/downloads

eForum: AOpen eForum is provided to discuss our products with other users, in

which your problem probably had been discussed before or will be answered.

After log on, you may select your preferred language under “Multi-language”.

http://club.aopen.com.tw/forum/

Contact Distributors/Resellers: We sell our products through resellers

and integrators. They should know your system configuration very well

and should be able to solve your problem efficiently and provide important

reference for you.

symptom before contacting us. The part number, serial number

and BIOS version are also very helpful.

Autres manuels pour AK77-600GN

Table des matières

Autres manuels AOpen Carte mère

AOpen

AOpen Fortress 9500 Manuel utilisateur

AOpen

AOpen AX4SG WLAN Guide de configuration

AOpen

AOpen MX36CE Guide de configuration

AOpen

AOpen AK75PRO Manuel utilisateur

AOpen

AOpen DXPL-U Guide de configuration

AOpen

AOpen AX45F-8X MAX Guide de configuration

AOpen

AOpen AK77-333 Fiche technique

AOpen

AOpen i945GTm-VHL Manuel utilisateur

AOpen

AOpen MX64 Manuel utilisateur

AOpen

AOpen i915Ga-HFS Fiche technique

AOpen

AOpen AX45 Guide de configuration

AOpen

AOpen AX4PE Tube-G Manuel utilisateur

AOpen

AOpen MX4LR TV Guide de configuration

AOpen

AOpen i945Ga-PLF Manuel utilisateur

AOpen

AOpen AX4SP-G Guide de configuration

AOpen

AOpen AX6BC Pro II Millennium Edition Manuel utilisateur

AOpen

AOpen AX45-533 PLUS Fiche technique

AOpen

AOpen AX4GEFM Manuel utilisateur

AOpen

AOpen i975Xa- YDG Manuel utilisateur

AOpen

AOpen AX37D Pro Guide de configuration

AOpen

AOpen AK73 Series Guide de configuration

AOpen

AOpen AX4GE Tube-G Fiche technique

AOpen

AOpen AK77-8X Guide de configuration

AOpen

AOpen MX4GR Guide de configuration

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur