Anviz M5 PRO Manuel utilisateur
Outdoor Fingerprint & Card
Reader/Controller
M5 Pro
Quick Guide V1.1
1
Package List
CD
ID Card
M5 Pro
Outdoor Fingerprint & Card
Reader/Controller
Device Quick Guide
X4
RJ45 Connector USB
Note:
1. Please check if the package contains all the
items listed above. Contact the distributor
if there is any problem.
2. Please keep the product away from the
magnetic field, and avoid causing any
damage to the device.
3. Please use the original power supply or
refer to the instruction to get the right
power supply.
4. Please strictly follow the instructions to
install the product. Any damage to it
caused by incorrect operation and wiring
are not under warranty.
Screws
M5 Pro
了解更多信息，请访问 [email protected]，或发送电子邮箱 [email protected] 获取更多帮助。
©2018 安威士 ● 中国
户外指纹&RFID卡门禁一体机
快速指南 V1.0
There are 4 cards in the package:
Enroll Card Delete Card User Card * 2.
Illustration for placing finger
Always place finger in
the center of the sensor.
Try to place your finger covers the entire sensor window.
Correct method
Incorrect method
DO NOT slide your finger
during the fingerpint
verification process.
DO NOT just use your fingertip.
DO NOT place finger
at an angle.
DO NOT place finger away from
the center of the sensor window.
DO NOT move your finger before
the backlight of sensor turns off.
DO NOT take off finger during
the fingerprint verification
process. 2
( Straighten your finger and then place it on the sensor.Ensure the finger is flat and covers
the entire sensor window)
Installation Diagram
Appearance
Steps: Steps:
Screw Hole
Mini USB Port
Function Button
Indicator LED
Three colour: Red,
Blue and Green.
Fingerprint Sensor
Place the finger here.
3
Card Reader Area
Swipe the card here.
Step1: Drill holes in the wall
follow the hole position on
back panel.
Step2: Install and fix back
panel, connect related cables.
Step3: Place M5 Pro on back
panel, fix screw at the bottom
of M5 Pro.
Restart button
Step1
Step2
Step3
Without back panel install way:Back panel install way:
2.52in.(64mm)
1.42in.(36mm)
0.41in.(10.5mm)
Fix M5 screws directly to the bottom
shell behind the wall, the depth of
screws is 8mm. This install method is
unique, safe and convenient. Package
list has no these screws, according to
wall thickness select the length of M5
screws.
4
Wiring Instruction
Connect RJ45
Anviz Wiegand Wiring:
8
+12V
+12V
SC011 and the device are paired by
Anviz wiegand to be a distributed access
control system.
Exit Button
Switch Power Supply
Power off to unlock
Power on to unlock
Black
Black
DC12V
GND
GND
GND
RS485A
RS485B
NO
COM
NC
Wiegand DATA0 Output
Wiegand DATA1 Output
D/S
Tamper alarm
Tamper alarm
4
Make sure correct wiring between M5 Pro and SC011, power on them, then move slide switch to
‘PROGRAM MODE’ as below:
Authorization
Mode
Power On：
Red Light
Between M5 Pro and Anviz SAC844 or other Access Controller as below:
Match registered fingerprint or swipe
registered card on M5 Pro, then SC011 will
beep once, means authorized successfully.
Then move slide switch to right(OFF).
1. Anviz Wiegand data output format:
ALL registered users output devieces’ last eight serial number.(For example, SN of one device
is 1050000014470004, then Anviz Wiegand output 14470004.)
2. Wiegand 26 data output format:
Card user: Output card number.(Decimal)
Fingerprint user: Output ID number
3. Wiegand output format can be set by PC software
Wiegand 26 Wiring:
SC011 authorization setting:
Switch in‘PROGRAM’on the SC011: Move slide swith to left(ON).
Wiegand data output format:
5
Switch Power
Supply
Switch Power
Supply
6
Power off to unlock
Power off to unlock
Power on to unlock
Power on to unlock
Important notice:
Please carefully follow this wiring instruction. Any damage caused by incorrect wiring is not covered by warranty.
Wiring Type Access Controller
Switching Power Supply
Put the CD in the managemet computer. The installation program will run automatically.
7
Loose the screw on the bottom of M5 Pro,
then pull up the front case, seperate from
back panel.
Connect USB cable between M5 Pro and
PC which has installed software.
Working with Management Software
1. Install the Management Software on Computer
How to connect M5 Pro with Software?
1st Method: Mini USB
Pay Attention:
If management cards are registered,
indicator light turns yellow and flashes. You
must verify any management card first. If no
management card is registered, you can
communicate with M5 Pro directly.
2st Method: Mini USB
Local Area Network (TCP/IP)
Right click on the device icon
and choose ‘Set the IP configuration’
to set correct network enviroment
parameters such as above window.
8
2. Enable Communication between M5 Pro and the Management Software CrossChex
*Turn on management software CrossChex
*Go to Device tab. Search and add the M5 Pro to management software CrossChex
*Click Synchronize Time button to communicate with M5 Pro. If Synchronize is
successful, the device icon will turn to blue.
3. The Management Software CrossChex Features
*Device\Backup User: Download user info from M5 Pro to CrossChex
*Device\Download Records: Download records from M5 Pro to CrossChex
*User\Modify: Edit name or other user info. Then click “Upload User”to Upload
user info to M5 device
Function Button
9
*Record\Search: search and view the records
*Attendance: Calculate, Search results and generate reports
*Data\Backup Database: Backup Database
*Setting\Shift: Set up Time table and Scheduling
*Device\Device Parameter: Set up device, Clear records on M5 Pro or Reset M5 Pro to
factory settings
Table des matières
Autres manuels Anviz Contrôleurs d'accès IP
Anviz
Anviz W 1 Manuel utilisateur
Anviz
Anviz T5Pro Manuel utilisateur
Anviz
Anviz T5 Manuel utilisateur
Anviz
Anviz OA200 Manuel utilisateur
Anviz
Anviz T50 Manuel utilisateur
Anviz
Anviz TC550 Manuel utilisateur
Anviz
Anviz C2C Manuel utilisateur
Anviz
Anviz EP10 Manuel utilisateur
Anviz
Anviz VF30 Manuel utilisateur
Anviz
Anviz P7 Manuel utilisateur
