Analog Devices LTC6955 Guide de configuration rapide

DEMO MANUAL DC2611A

Rev. 0

DESCRIPTION

LTC6955/LTC6955-1

Ultralow Jitter 11 Output

Fanout Buffer

Demonstration Circuit 2611A features the LT C

6955/

LTC6955-1, Ultralow Jitter 11 Output Fanout Buffers.

By default, the DC2611A is powered from a single 3.3V

supply. An option is provided to power to the DC2611A

from dual supplies, allowing for the LTC6955’s output

supply pins to connect to an LTC Silent Switcher

and the

LTC6955 input supply pin to connect to a low noise LDO.

The differential inputs and six of the differential outputs

are populated with 0.5" spaced SMA connectors. These

outputs are AC-coupled with 50Ω transmission lines

All registered trademarks and trademarks are the property of their respective owners.

making them suitable to drive 50Ω impedance instru-

ments. The remaining four differential outputs are termi-

nated with 100Ω.

A calibration path is provided to aid in accurate LTC6955

propagation delay measurements. The calibration path

can be also reconfigured as a DC path, which allows for

a convenient method of locking the LTC6955 outputs to

an external PLL/VCO, as shown in Figure2.

Design files for this circuit board are available.

Figure1. DC2611A Connections

CAL_IN,

SMA

Single Supply 3.3V Input,

banana jacks J27 & J28

OUT1, CML

AC-coupled

Outputs, SMA

OUT0, CML

AC-coupled

Outputs, SMA

CAL_OUT,

SMA

OUT8, CML

AC-coupled

Outputs, SMA

OUT10, CML

AC-coupled

Outputs, SMA

IN Input, SMA

VIN33 Option,

Refer to

DC2611 Reconfiguration

OUT6, CML

AC-coupled

Outputs, SMA

OUT4, CML

AC-coupled

Outputs, SMA

TEMP, turret

OUTPUT SEL,

Switches

FILT, Header

DEMO MANUAL DC2611A

Rev. 0

QUICK START PROCEDURE

The DC2611A is easy to set up to evaluate the perfor-

mance of the LTC6955. Follow the procedure below

DC2611A Configuration

1. Connect J27 and J28 to a power supply and apply power

(see Figure1 and the Typical DC2611A Requirements

and Characteristics table).

2. Connect a low phase-noise (or jitter) single-ended sig-

nal to IN–(J25). Refer to the LTC6955 data sheet for

acceptable input frequencies and amplitudes.

3. Connect desired output (OUT10, OUT8, OUT6, OUT4,

OUT1 or OUT0) to a test instrument or other demo

board to evaluate performance. Terminate the unused

outputs with 50Ω.

4. Ensure SW0:3 are configured to enable the desired

output. Setting SEL[3:1]=H and SEL0=L enables all

outputs. Refer to Table1 for a list of SEL[3:0] settings

vs output states.

Be sure to power down or terminate any unused RF output

with 50Ω, or poor spurious performance may result.

Troubleshooting

If the LTC6955 does not output a signal

1. Ensure LTC6955 input signal is connected to the

LTC6955 IN– pin, not the LTC6955 IN+ pin.

If DC2611A performance is less than the LTC6955 data

sheet specifications:

1. For unexpected spurious response, verify power sup-

plies are low noise and spurious free power supplies.

Power supplies that are based off a switching regulator

architecture are known to generate spurs on low jitter

clock outputs.

2. For poor phase noise results, verify the phase noise

specifications of the input signal and the phase noise

measurement instrument. Traditional signal sources

and spectrum analyzers have higher phase noise than

the LTC6955 and will degrade measurement results. To

measure phase noise performance it is recommended

to use a low jitter oscillator and a signal source analyzer,

such as Keysight’s (previously Agilent/HP) E5052.

3. Contact the factory for further troubleshooting.

Table1. LTC6955 SEL[3:0] Settings vs Output States

SEL[3:0]

TEMP

DIODE OUT10 OUT9 OUT8 OUT7 OUT6 OUT5 OUT4 OUT3 OUT2 OUT1 OUT0

0x0 Pwrdn

0x1 ON ON Pwrdn ON Pwrdn ON Pwrdn Pwrdn Pwrdn Pwrdn Pwrdn Pwrdn

0x2 ON ON Pwrdn ON Pwrdn ON Pwrdn ON Pwrdn Pwrdn Pwrdn Pwrdn

0x3 ON ON Pwrdn ON Pwrdn ON Pwrdn ON Pwrdn ON Pwrdn Pwrdn

0x4 ON ON ON ON Pwrdn ON Pwrdn ON Pwrdn ON Pwrdn Pwrdn

0x5 ON ON Inverted ON Pwrdn ON Pwrdn ON Pwrdn ON Pwrdn Pwrdn

0x6 ON ON ON ON ON ON Pwrdn ON Pwrdn ON Pwrdn Pwrdn

0x7 ON ON Inverted ON Inverted ON Pwrdn ON Pwrdn ON Pwrdn Pwrdn

0x8 ON ON ON ON ON ON ON ON Pwrdn ON Pwrdn Pwrdn

0x9 ON ON Inverted ON Inverted ON Inverted ON Pwrdn ON Pwrdn Pwrdn

0xA ON ON ON ON ON ON ON ON ON ON Pwrdn Pwrdn

0xB ON ON Inverted ON Inverted ON Inverted ON Inverted ON Inverted Pwrdn

0xC ON ON ON ON ON ON ON ON ON ON ON Pwrdn

0xD ON ON Inverted ON Inverted ON Inverted ON Inverted ON Inverted ON

0xE ON ON ON ON ON ON ON ON ON ON ON ON

0xF ON Pwrdn

DEMO MANUAL DC2611A

Rev. 0

DC2611A RECONFIGURATION

The following covers the hardware reconfiguration of the

DC2611A. Refer to LTC6955 data sheet for a better under-

standing of device specific considerations.

Power Supply Options

Table2 provides the power supply options for DC2611A.

By default the DC2611A is setup to use the single supply

option. However, a dual supply option is available to power

the higher current supply from our Silent Switcher, such

as the LT8609S. The Silent Switcher improves the power

efficiency over the low noise LDO. A spurious free supply,

such as a low noise LDO, is required on the LTC6955’s

VIN+supply pin.

Table2. Power Supply Options

Power Supply Voltage/Current

(Recommended Supply)

DEFAULT OPTION R18 J27 (3.3V) E10 (VIN33)

x Single

Supply

Installed 3.3V/750mA

(Low Noise LDO)

Dual

Supply

Do Not

Install

3.3V/750mA

(Silent Switcher)

3.3V/150mA

(Low Noise LDO)

Input Termination Options

Table3 provides the single-ended and differential input

termination options. By default the DC2611A is setup for

a single-ended input on the IN–SMA (J25). For best per-

formance different termination networks are provided for

input signals <5GHz and input signals >5GHz.

LTC6955-1 Divide by Two Coupling Spur

To help reduce the LTC6955-1’s OUT10 /2 coupling spur

to other outputs a ferrite bead (FB1) should be installed

on the OUT10 supply pin, VOUT+ (Pin 5). For the LTC6955

FB1 should be a 0Ω resistor.

CML Outputs, OUT[10:0]

The DC2611A has 11 CML outputs. Six of these outputs

are AC-coupled and brought out to SMAs (OUT10, OUT8,

OUT6, OUT4, OUT1 or OUT0). To drive 50Ω impedance

instruments connect OUTx+ to the instrument and OUTx–

to a 50Ω termination, or vice versa.

The remaining five outputs (OUT9, OUT7, OUT5, OUT3,

and OUT2) are terminated with a 100Ω resistor on board.

To connect these outputs to a 50Ω instrument, remove

the 100Ω termination, and install the appropriate SMAs

and AC blocking capacitors.

Refer to LTC6955 data sheet for differential termination

options.

Alternate Configuration Options

To take advantage of the LTC6955’s maximum output

frequency and ultralow output additive phase noise,

the DC2611A (LTC6955, LTC6955-1), the DC2609A

(LTC6952) and the VCO rider board (DC2664A) were

designed to mate directly together, as shown in Figure2.

This setup allows for options to lock the LTC6952 refer-

ence input to:

A) A <7.5GHz VCO and LTC6955-1 output frequency, by

utilizing the LTC6955-1 divide by two output on OUT10

to drive the LTC6952 VCO input. (refer to Figure2)

B) Any VCO and create lower jitter clocks from a LTC6955

or LTC6955-1 output than a standalone LTC6952

produces.

Refer to the LTC6952 and LTC6955 data sheet’s typical

application for measured results. Refer to the DC2664A

demo manual for recommendation on loop filter compo-

nent placement.

Table3. Input Termination Options (*)

DEFAULT TERMINATION R8 (Ω) R9 (Ω) R10 (Ω) R11 (Ω) R19 (Ω) R20 (Ω) C58 C59 C60 C61

DC2611A-A SE, IN–, <5GHz 75 DNI 30 DNI DNI DNI 0.1uF 0.1uF DNI 0.1uF

DC2611A-B SE, IN–, ≥5GHz DNI DNI DNI 1nH DNI 49.9 DNI 1pF 1pF DNI

SE, IN+, <5GHz 30 DNI 75 DNI DNI DNI 0.1uF DNI 0.1uF 0.1uF

SE, IN+, ≥5GHz DNI DNI DNI 1nH 49.9 DNI DNI 1pF 1pF DNI

DIFF, CML or PECL, <5GHz DNI 160 DNI DNI DNI DNI DNI 0.1uF 0.1uF DNI

DIFF, CML or PECL, ≥5GHz DNI DNI DNI 1nH DNI DNI DNI 1pF 1pF DNI

DIFF, LVDS DNI DNI DNI 160 DNI DNI DNI 0.1uF 0.1uF DNI

*SE = Single-Ended, DIFF = Differential, DNI = Do Not Install

DEMO MANUAL DC2611A

Rev. 0

Change C56 & C57

to 0 ohm resistors

DC2611A RECONFIGURATION

Figure2. Alternate Configuration, Locking LTC6955 Outputs to an External PLL/VCO

DEMO MANUAL DC2611A

Rev. 0

TYPICAL DC2611A REQUIREMENTS AND CHARACTERISTICS

Table4.

PARAMETER INPUT OR OUTPUT PHYSICAL LOCATION DETAILS

3.3V Power Supply Input J27 and J28 BNC Banana Jacks If R18 populated, default option, single supply: 3.3V low-

noise and spur-free supply, 1A;

If R18 depopulated, dual supply option, allows for

experiments with more efficient power supply evaluation

(Silent Switcher).

See 3.3V power supply #2 (VIN33)

3.3V Power Supply #2 (VIN33) Input E10 Turret (VIN33) If R18 depopulated, dual supply option, 3.3v low-noise and

spur-free supply, 150mA;

OUT10+; OUT10– Two Outputs J1 and J2 SMA Connectors* CML, AC-coupled, 800mVP-P differential

OUT8+; OUT8– J5 and J6 SMA Connectors*

OUT6+; OUT6– J21 and J22 SMA Connectors*

OUT4+; OUT4– J17 and J18 SMA Connectors*

OUT1+; OUT1– J11 and J12 SMA Connectors*

OUT0+; OUT0– J9 and J10 SMA Connectors*

OUT9+; OUT9– Two Outputs

(Not Connected)

J3 and J4 (SMA Not Populated) On board differential 100Ω termination

OUT7+; OUT7– J7 and J8 (SMA Not Populated)

OUT5+; OUT5– J19 and J20 (SMA Not Populated)

OUT3+; OUT3– J15 and J16 (SMA Not Populated)

OUT2+; OUT2– J13 and J14 (SMA Not Populated)

IN+ Input

(Not Connected)

J26 SMA Connector Default: Not connected

(see Table3, for correct input termination options)

IN- Input J25 SMA Connector Default: Preferred single-ended input

(see Table3, for correct input termination options)

FILT Input, Center Pin JP1 3-Pin Header L(Default): FILT disabled, set by pull-down resistor

H: FILT enabled

TEMP Output E1 Turret (TEMP) Internal temperature diode

*Any unused RF output must be powered down or terminated with 50Ω, or poor spurious performance may result.

ASSEMBLY OPTIONS

Table5. DC2611A Assembly Options

ASSEMBLY VERSION U1 PART NUMBER

DC2611A-A LTC6955IUKG

DC2611A-B LTC6955IUKG-1

DEMO MANUAL DC2611A

Rev. 0

PCB LAYOUT

Top Layer

DEMO MANUAL DC2611A

Rev. 0

PARTS LIST

ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER

Required Circuit Components

1 15 C1, C2, C5, C6, C9-C12, C17, C18,

C21, C22, C50, C56, C57

CAP., X7R, 0.1µF, 10V, 10%, 0402 MURATA, GRM155R71A104KA01D

2 0 C3, C4, C7, C8, C13-C16, C19, C20 CAP., 0402 OPT

3 12 C25-C36 CAP., X7R, 0.01µF, 6.3V, 10%, 0201 MURATA, GRM033R70J103KA01D

4 11 C38-C48 CAP., X5R, 1µF, 16V, 10%, 0402 MURATA, GRM155R61C105KE01D

5 1 C49 CAP., X7R, 10µF, 25V, 10%, 1206 MURATA, GRM31CR71E106KA12L

6 1 C62 CAP., TANT., 330µF, 10V, 10%, 7343 AVX, TPME337K010R0035

7 10 E1-E10 TURRET, TESTPOINT 0.064" MILL-MAX, 2308-2-00-80-00-00-07-0

8 1 JP1 CONN., HEADER, MALE, 1X3, 2mm, THT WURTH ELEKTRONIK, 62000311121

9 16 J1, J2, J5, J6, J9-J12, J17, J18,

J21-J26

CONN., SMA 50Ω EDGE-LAUNCH, CON-SMA-R CCSJ, 142-0701-851

10 0 J3, J4, J7, J8, J13-J16, J19, J20 CONN., SMA 50Ω EDGE-LAUNCH, CON-SMA-R OPT

11 2 J27, J28 CONN, JACK, BANANA KEYSTONE, 575-4

12 2 R1, R2 RES., CHIP, 10k, 1/10W, 1% 0402 VISHAY, CRCW040210K0FKED

13 1 R3 RES., CHIP, 100k, 1/10W, 1% 0402 VISHAY, CRCW0402100KFKED

14 5 R4, R5, R6, R7, R12 RES., CHIP, 100Ω, 1/16W, 1% 0402 VISHAY, CRCW0402100RFKED

15 1 R18 RES., CHIP, 0Ω, 1/10W, 0402 VISHAY, CRCW04020000Z0ED

16 4 SW0, SW1, SW2, SW3 SWITCH, SLIDE SPDT 200MA 30V, SW-EG1218 E-SWITCH, EG1218

17 1 SHUNT ON JP1 (1&2) SHUNT, 2mm WURTH ELEKTRONIK, 60800213421

18 4 MH1-MH4 STANDOFF, NYLON, 0.5, 1/2" WURTH ELEKTRONIK, 702935000

19 1 DUST CAP FOR J26 WYHP DUST CAP FOR SMA FEMALE RF CONN AMAZON

DEMO MANUAL DC2611A

Rev. 0

PARTS LIST

ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER

DC2611A3-A Required Circuit Components

1 1 DC2611A3-GENERAL BOM

2 3 C58, C59, C61 CAP., X7R, 0.1µF, 10V, 10%, 0402 MURATA, GRM155R71A104KA01D

3 0 C60 CAP., 0402 OPT

4 1 FB1 RES., CHIP, 0Ω, 1/20W, 1% 0201 VISHAY, CRCW02010000Z0ED

5 1 R8 RES., CHIP, 75Ω, 1/16W, 1% 0402 VISHAY, CRCW040275R0FKED

6 0 R9, R11, R19, R20 RES., 0402 OPT

7 1 R10 RES., CHIP, 30Ω, 1/16W, 1% 0402 VISHAY, CRCW040230R0FKED

8 1 U1 I.C., ULTRALOW JITTER 11 OUTPUT FANOUT BUFFER,

QFN52UKG-7X8

LINEAR TECH., LTC6955IUKG

DC2611A3-B Required Circuit Components

1 1 DC2611A3-GENERAL BOM

2 0 C58, C61 CAP., 0402 OPT

3 2 C59, C60 CAP., C0G, 1pF, 50V, 10%, 0402 MURATA, GJM1555C1H1R0CB01

4 1 FB1 IND., 47ΩS AT 100MHz, FERRITE BEAD, 0201 TDK, MMZ0603D470ET000

5 0 R8, R9, R10, R19 RES., 0402 OPT

6 1 R11 IND., FIXED, HIFREQ, 47nH 5% 0.15A, 0402 COIL CRAFT, 0402CS-1N0XJL

7 1 R20 RES., CHIP, 49.9, 1/16W, 1% 0402 VISHAY, CRCW040249R9FKED

8 1 U1 I.C., ULTRALOW JITTER 11 OUTPUT FANOUT BUFFER,

QFN52UKG-7X8

LINEAR TECH., LTC6955IUKG-1

DEMO MANUAL DC2611A

Rev. 0

Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog

Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications

subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices.

SCHEMATIC DIAGRAM

D D

C C

B B

A A

3.3V SUPPLIES

1. ALL RESISTORS AND CAPACITORS ARE 0402.

NOTES: UNLESS OTHERWISE SPECIFIED

PLACE ON TOP SIDE

PLACE ON BOTTOM SIDE

[2]

[2]. J26 = INSTALLED BUT UNUSED.

[3]. COMPONENTS WILL BE STUFFED WITH DEFAULT VALUES.

FOR INPUT SIGNALS < 5GHz

DIFFERENTIAL

S-E IN-

(DEFAULT FOR -A)

S-E IN+

R8 R9 R10C59 C60

OPT75 300.1uF

0.1uF0.1uF

7530 OPTOPT

OPT

0.1uF

OPTOPT 160

OTHER VALUES ARE FOR LAB USED ONLY.

[3]

ALL INPUT AND OUTPUT CONNECTIONS ARE SAME

LENGTH, 50 OHM CONTROLLED IMPEDANCE.

[4]. ASSEMBLY TABLE:

ASSY U1 SUFFIX

A LTC6955

LTC6955-1 1

DC2611A -

BDC2611A -

C58 C61

0.1uF

R11 R19 R20

OPT

FOR INPUT SIGNALS > 5GHz

DIFFERENTIAL

S-E IN-

(DEFAULT FOR -B)

S-E IN+

R8 R9 R10C59 C60

OPT

1pF

OPT

OPTOPT

C58 C61 R11 R19 R20

1nH OPT

OPT

49.9

OPT

49.9

OPT

1pF

OPT

1nH

FB1 FB1

MMZ0603

OPT OPT

0 OHM

MMZ0603

0 OHM

OUT0+

SEL3

OUT0-

OUT1+

OUT1-

OUT2-

OUT3+

OUT4+

OUT4-

OUT5+

OUT5-

OUT6+

OUT6-

OUT7+

OUT7-

OUT8+

OUT8-

OUT9-

OUT10-

OUT10+

TEMP

IN-

IN+

OUT9+

CAL_INCAL_OUT

OUT3-

FILT

SEL0

SEL1

SEL2

OUT2+

3.3V

3.3V 3.3V 3.3V 3.3V

3.3V

VIN33

3.3V

REVISION HISTORY

DESCRIPTION DATEAPPROVEDECO REV

CHRIS P.PRODUCTION

__ 3 07-07-17

REVISION HISTORY

DESCRIPTION DATEAPPROVEDECO REV

CHRIS P.PRODUCTION

__ 3 07-07-17

REVISION HISTORY

DESCRIPTION DATEAPPROVEDECO REV

CHRIS P.PRODUCTION

__ 3 07-07-17

SIZE

DATE:

IC NO. REV.

SHEET OF

TITLE:

APPROVALS

PCB DES.

APP ENG.

TECHNOLOGY Fax: (408)434-0507

Milpitas, CA 95035

Phone: (408)432-1900

1630 McCarthy Blvd.

LTC Confidential-For Customer Use Only

CUSTOMER NOTICE

LINEAR TECHNOLOGY HAS MADE A BEST EFFORT TO DESIGN A

CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS;

HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO

VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL

APPLICATION. COMPONENT SUBSTITUTION AND PRINTED

CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT

PERFORMANCE OR RELIABILITY. CONTACT LINEAR

TECHNOLOGY APPLICATIONS ENGINEERING FOR ASSISTANCE.

THIS CIRCUIT IS PROPRIETARY TO LINEAR TECHNOLOGY AND

SCHEMATIC

SUPPLIED FOR USE WITH LINEAR TECHNOLOGY PARTS.

SCALE = NONE

www.linear.com

DEMO CIRCUIT 2611A

Friday, July 07, 2017

ULTRALOW JITTER 11 OUTPUT FANOUT BUFFER

N/A

LTC6955IUKG, LTC6955IUKG-1

KIM T.

CHRIS P.

SIZE

DATE:

IC NO. REV.

SHEET OF

TITLE:

APPROVALS

PCB DES.

APP ENG.

TECHNOLOGY Fax: (408)434-0507

Milpitas, CA 95035

Phone: (408)432-1900

1630 McCarthy Blvd.

LTC Confidential-For Customer Use Only

CUSTOMER NOTICE

LINEAR TECHNOLOGY HAS MADE A BEST EFFORT TO DESIGN A

CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS;

HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO

VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL

APPLICATION. COMPONENT SUBSTITUTION AND PRINTED

CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT

PERFORMANCE OR RELIABILITY. CONTACT LINEAR

TECHNOLOGY APPLICATIONS ENGINEERING FOR ASSISTANCE.

THIS CIRCUIT IS PROPRIETARY TO LINEAR TECHNOLOGY AND

SCHEMATIC

SUPPLIED FOR USE WITH LINEAR TECHNOLOGY PARTS.

SCALE = NONE

www.linear.com

DEMO CIRCUIT 2611A

Friday, July 07, 2017

ULTRALOW JITTER 11 OUTPUT FANOUT BUFFER

N/A

LTC6955IUKG, LTC6955IUKG-1

KIM T.

CHRIS P.

SIZE

DATE:

IC NO. REV.

SHEET OF

TITLE:

APPROVALS

PCB DES.

APP ENG.

TECHNOLOGY Fax: (408)434-0507

Milpitas, CA 95035

Phone: (408)432-1900

1630 McCarthy Blvd.

LTC Confidential-For Customer Use Only

CUSTOMER NOTICE

LINEAR TECHNOLOGY HAS MADE A BEST EFFORT TO DESIGN A

CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS;

HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO

VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL

APPLICATION. COMPONENT SUBSTITUTION AND PRINTED

CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT

PERFORMANCE OR RELIABILITY. CONTACT LINEAR

TECHNOLOGY APPLICATIONS ENGINEERING FOR ASSISTANCE.

THIS CIRCUIT IS PROPRIETARY TO LINEAR TECHNOLOGY AND

SCHEMATIC

SUPPLIED FOR USE WITH LINEAR TECHNOLOGY PARTS.

SCALE = NONE

www.linear.com

DEMO CIRCUIT 2611A

Friday, July 07, 2017

ULTRALOW JITTER 11 OUTPUT FANOUT BUFFER

N/A

LTC6955IUKG, LTC6955IUKG-1

KIM T.

CHRIS P.

SW2

EG1218

SEL2

J10

SMA

OUT0-

C25

0.01uF

0201

E10

VIN33

C56

0.1uF

J13

SMA

OUT2+

OPT

0.1uF

J26

SMA

IN+

SMA

OUT9+

OPT

C61

U1 [4]

VOUT+ 32

OUT1+ 31

OUT1- 30

VOUT+ 29

OUT2+ 28

OUT2- 27

VOUT+

OUT3+

OUT3-

VOUT+

SEL3

VD+

OUT10-

OUT10+

VOUT+

OUT9-

OUT9+

VOUT+

OUT8-

OUT8+

VOUT+

OUT7-

VIN+ 39

IN- 38

OUT7+

VOUT+

OUT5+

OUT6+

OUT4-

OUT4+

OUT5-

IN+ 37

NC 36

OUT0+ 34

VOUT+ 35

OUT6-

OUT0- 33

FILT 40

GND 41

NC 42

NC 43

NC 44

NC 45

NC 46

NC 47

NC 48

TEMP 49

SEL0 50

SEL1 51

SEL2 52

EP 53

C19

OPT

C20

OPT

GND

J14

SMA

OUT2-

OPT

JP1

HD1X3-079

FILT

OPT

C32

0.01uF

0201

C15

OPT

SMA

OUT9-

OPT

C57

0.1uF

C30

0.01uF

0201

C18

0.1uF

C28

0.01uF

0201

J16

SMA

OUT3-

OPT

C14

OPT

J17

SMA

OUT4+

0.1uF

J23

SMA

CAL_OUT

100

GND

SW1

EG1218

SEL1

100

J20

SMA

OUT5-

OPT

C50

0.1uF

C10

0.1uF

J18

SMA

OUT4-

C31

0.01uF

0201

10k

GND

C48

1uF

SMA

OUT7+

OPT

C35

0.01uF

0201

C59

C17

0.1uF

SMA

OUT8+

OPT

J15

SMA

OUT3+

OPT

C42

1uF

100

0.1uF

C21

0.1uF

J11

SMA

OUT1+

J24

SMA

CAL_IN

R18

C13

OPT

10k

R20

SMA

OUT8-

C44

1uF

C22

0.1uF

J27

3.3V

KEY-575

GND

SMA

OUT10-

C43

1uF

C29

0.01uF

0201

C38

1uF

0.1uF

SMA

OUT0+

C46

1uF

J21

SMA

OUT6+

J19

SMA

OUT5+

OPT

C47

1uF

C62

330uF

10V

7343

TEMP

C45

1uF

OPT

C34

0.01uF

0201

J25

SMA

IN-

SW3

EG1218

SEL3

C11

0.1uF

J12

SMA

OUT1-

C27

0.01uF

0201

J22

SMA

OUT6-

100

100k C9

0.1uF

C39

1uF C40

1uF C41

1uF

FB1

[3]

R10

C12

0.1uF

C26

0.01uF

0201

R19

GND

SMA

OUT7-

OPT

C58

GND

C36

0.01uF

0201

SW0

EG1218

SEL0

C49

10uF

1206 C33

0.01uF

0201

J28

GND

KEY-575

C16

OPT

SMA

OUT10+

R11

R12

100

C60

OPT

DEMO MANUAL DC2611A

Rev. 0

 ANALOG DEVICES, INC. 2019

www.analog.com

01/19

ESD Caution

ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection

circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.

Legal Terms and Conditions

By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and

conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation

Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”)

and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to

Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and

agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted

is expressly made subject to the following additional limitations:Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board;and (ii) permit any Third

Party to access the Evaluation Board. As used herein, the term “Third Party”includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is

NOT sold to Customer;all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all

be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of

use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile

or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited

to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS

Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF

LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS”AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY

DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE

IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS

LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING

BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE

HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States

federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts

(excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits

to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Analog Devices Matériel informatique

Analog Devices

Analog Devices SHARC ADSP-214 Series Guide d'application

Analog Devices

Analog Devices Linear LTC3114-1 Guide de configuration rapide

Analog Devices

Analog Devices Blackfin Manuel utilisateur

Analog Devices

Analog Devices AD9284-250EBZ Manuel utilisateur

Analog Devices

Analog Devices ADSP-SC58 Series Guide d'application

Analog Devices

Analog Devices HPUSB Manuel utilisateur

Analog Devices

Analog Devices UG-397 Manuel utilisateur

Analog Devices

Analog Devices ADSP-TS101 TigerSHARC Guide d'application

Analog Devices

Analog Devices Blackfin Manuel utilisateur

Analog Devices

Analog Devices iSensor ADIS/EVAL/USB Manuel d'instructions

Analog Devices

Analog Devices ADSP-BF535 Blackfin Guide d'application

Analog Devices

Analog Devices EV-RPG2 Manuel utilisateur

Analog Devices

Analog Devices ADuCM322 Manuel utilisateur

Analog Devices

Analog Devices EZ-Board ADSP-21489 Manuel utilisateur

Analog Devices

Analog Devices ADSP-21000 Guide de l'utilisateur

Analog Devices

Analog Devices ADDS-218X-ICE-2.5V Manuel utilisateur

Analog Devices

Analog Devices ADSP-BF53x EZ-Extender 1 Manuel utilisateur

Analog Devices

Analog Devices ADAU1961 Manuel utilisateur

Analog Devices

Analog Devices SHARC ADSP-2136 Series Guide d'application

Analog Devices

Analog Devices Blackfin ADSP-BF537 Guide d'application

Analog Devices

Analog Devices ICE-100B Manuel utilisateur

Analog Devices

Analog Devices Blackfin Audio EZ-Extender Manuel utilisateur

Analog Devices

Analog Devices Linear ADP5070 Guide de configuration rapide

Analog Devices

Analog Devices MAX77831 Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur