Analog Devices Blackfin Audio EZ-Extender Manuel utilisateur
a
Blackfin®EZ-Extender®
Manual
Revision 4.1, July 2012
Part Number
82-000735-01
Analog Devices, Inc.
One Technology Way
Norwood, Mass. 02062-9106
Copyright Information
© 2012 Analog Devices, Inc., ALL RIGHTS RESERVED. This docu-
ment may not be reproduced in any form without prior, express written
consent from Analog Devices, Inc.
Printed in the USA.
Disclaimer
Analog Devices, Inc. reserves the right to change this product without
prior notice. Information furnished by Analog Devices is believed to be
accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use; nor for any infringement of patents or other rights of
third parties which may result from its use. No license is granted by impli-
cation or otherwise under the patent rights of Analog Devices, Inc.
Trademark and Service Mark Notice
The Analog Devices logo, Blackfin, CrossCore, EngineerZone,
EZ-Extender, EZ-KIT Lite, and VisualDSP++ are registered trademarks of
Analog Devices, Inc.
All other brand and product names are trademarks or service marks of
their respective owners.
Regulatory Compliance
The Blackfin EZ-Extender is designed to be used solely in a laboratory
environment. The board is not intended for use as a consumer end prod-
uct or as a portion of a consumer end product. The board is an open
system design which does not include a shielded enclosure and therefore
may cause interference to other electrical devices in close proximity. This
board should not be used in or near any medical equipment or RF devices.
The Blackfin EZ-Extender has been certified to comply with the essential
requirements of the European EMC directive 89/336/EEC (inclusive
93/68/EEC) and, therefore, carries the “CE” mark.
The Blackfin EZ-Extender has been appended to Analog Devices, Inc.
EMC Technical File (EMC TF) referenced “DSPTOOLS1” dated
December 21, 1997 and was declared CE compliant by an appointed
Notified Body (No.0673) as listed below.
Notified Body Statement of Compliance: Z600ANA1.017
Issued by: Technology International (Europe) Limited
56 Shrivenham Hundred Business Park
Shrivenham, Swindon, SN6 8TY, UK
The Blackfin EZ-Extender contains ESD (electrostatic discharge) sensitive
devices. Electrostatic charges readily accumulate on the human body and
equipment and can discharge without detection. Permanent damage may
occur on devices subjected to high-energy discharges. Proper ESD precau-
tions are recommended to avoid performance degradation or loss of func-
tionality. Store unused extender boards in the protective shipping package.
Blackfin EZ-Extender Manual v
CONTENTS
PREFACE
Product Overview ....................................................................... viii
Purpose of This Manual ................................................................ ix
Intended Audience ........................................................................ ix
Manual Contents ........................................................................... x
What’s New in This Manual ........................................................... x
Technical Support ......................................................................... xi
Supported Products ...................................................................... xii
Product Information .................................................................... xii
Analog Devices Web Site ........................................................ xii
EngineerZone ........................................................................ xiii
Related Documents ...................................................................... xiv
EZ-EXTENDER INTERFACES
ADC and Mixed-Signal HSC Interface .......................................... 1-1
DAC HSC Interface ...................................................................... 1-2
Camera Interface ........................................................................... 1-3
LCD Interface ............................................................................... 1-4
Contents
vi Blackfin EZ-Extender Manual
EZ-EXTENDER HARDWARE REFERENCE
System Architecture ...................................................................... 2-1
DIP Switches and Jumpers ............................................................ 2-4
Direction Control Switch (SW1) ............................................. 2-4
Clock Routing Switch (SW2) .................................................. 2-5
General Frame Sync Routing Switch (SW3) ............................. 2-7
LCD Frame Sync Routing Switch (SW4) ................................. 2-8
MISO Disconnect Jumper (P7) ............................................... 2-9
SMA Connector Clock Disconnect Jumper (P10) .................... 2-9
PPI Data Routing Jumper (P36) ............................................ 2-10
External Clock Disable Jumper (P37) .................................... 2-11
EZ-EXTENDER BILL OF MATERIALS
EZ-EXTENDER SCHEMATIC
INDEX
Blackfin EZ-Extender Manual vii
PREFACE
Thank you for purchasing the Blackfin EZ-Extender®, Analog Devices
(ADI) extender board to the EZ-KIT Lite® evaluation system for
ADSP-BF533 and ADSP-BF561 Blackfin® processors.
The Blackfin processors are embedded processors that support a Media
Instruction Set Computing (MISC) architecture. This architecture is the
natural merging of RISC, media functions, and digital signal processing
(DSP) characteristics towards delivering signal processing performance in
a microprocessor-like environment.
The Blackfin EZ-Extender is designed to be used in conjunction with the
CrossCore®Embedded Studio (CCES) and VisualDSP++®software
development environments. The development environment facilitates
advanced application code development and debug, such as:
• Create, compile, assemble, and link application programs written
in C++, C, and Blackfin EZ-Extender assembly
• Load, run, step, halt, and set breakpoints in application programs
• Read and write data and program memory
• Read and write core and peripheral registers
• Plot memory
To learn more about Analog Devices development software, go to
http://www.analog.com/processors/tools.
Example programs are available to demonstrate the capabilities of the
Blackfin EZ-Extender board.
Product Overview
viii Blackfin EZ-Extender Manual
Product Overview
The Blackfin EZ-Extender is a separately sold assembly that plugs onto
the expansion interface of the ADSP-BF533/BF561 EZ-KIT Lite evalua-
tion system.
The board extends the capabilities of the evaluation system by providing a
connection between the parallel peripheral interface (PPI) of the
ADSP-BF533 processor (the PPI0 and PPI1 interfaces of the ADSP-BF561
processor), an Analog Devices high-speed converter (HSC) evaluation
board, a camera evaluation board, and an LCD display device. Moreover,
the extender broadens the range of the EZ-KIT Lite applications by pro-
viding surface mounted (SMT) footprints for breadboard capabilities and
access to all of the pins on the EZ-KIT Lite’s expansion interface.
Please visit www.analog.com/EX1-Extender for additional information,
including CCES support.
The extender features:
• High-speed converter (HSC) evaluation board interface
• 40-pin, right angle, 0.1 in. spacing, female socket to con-
nect to analog-to-digital converter (ADC) boards
• 40-pin straight, 0.1 in. spacing header to connect to digi-
tal-to-analog converter (DAC) boards
• Switches for routing and direction selection
• RJ-45 with serial peripheral interconnect (SPI) to configure
converter registers
Blackfin EZ-Extender Manual ix
Preface
• Camera interface
• Connection to OmniVision OV6630AA evaluation boards
(This part is no longer available.)
• 32-pin, right angle, 0.1 in. spacing, female socket
• LCD interface
• 32-pin, right angle FLZ-type connector to connect to LCD
displays
• SMT footprint area
• 1206 and 805 footprints
• SOIC24 and SOIC20 footprints
• Dimensions
• 5 in (H) x 5 in (W)
Purpose of This Manual
The Blackfin EZ-Extender Manual describes the operation and configura-
tion of the components on the board. A schematic and a bill of materials
are provided as a reference for future ADSP-BF533 and ADSP-BF561
Blackfin processor board designs.
Intended Audience
This manual is a user’s guide and reference to the Blackfin EZ-Extender.
Programmers who are familiar with the Analog Devices Blackfin processor
architecture, operation, and development tools are the primary audience
for this manual.
Manual Contents
x Blackfin EZ-Extender Manual
Programmers who are unfamiliar with Analog Devices processors can use
this manual but should supplement it with other texts that describe your
target architecture. For the locations of these documents, see “Related
Documents”.
Programmers who are unfamiliar with CCES or VisualDSP++ should refer
to the online help and user’s manuals.
Manual Contents
The manual consists of:
• Chapter 1, “EZ-Extender Interfaces” on page 1-1
Provides basic board information.
• Chapter 2, “EZ-Extender Hardware Reference” on page 2-1
Provides information on the hardware aspects of the board.
• Appendix A, “EZ-Extender Bill Of Materials” on page A-1
Provides a list of components used to manufacture the Blackfin
EZ-Extender board.
• Appendix B, “EZ-Extender Schematic” on page B-1
Provides the resources to allow extender board-level debugging or
to use as a reference design. Appendix B is part of the online help.
What’s New in This Manual
This is revision 4.1 of the Blackfin EZ-Extender Manual. The manual has
been updated to include CCES information. In addition, modifications
and corrections based on errata reports against the previous manual revi-
sion have been made.
For the latest version of this manual, please refer to the Analog Devices
Web site.
Autres manuels pour Blackfin Audio EZ-Extender
2
Table des matières
Autres manuels Analog Devices Matériel informatique
Analog Devices
Analog Devices MAX22005 Manuel utilisateur
Analog Devices
Analog Devices ADSP-219 Series Guide d'application
Analog Devices
Analog Devices LTC5597 Manuel utilisateur
Analog Devices
Analog Devices EVAL-LTC7067-AZ Manuel utilisateur
Analog Devices
Analog Devices SHARC ADSP-214 Series Guide d'application
Analog Devices
Analog Devices ICE-100B Manuel utilisateur
Analog Devices
Analog Devices ADM1060 Manuel utilisateur
Analog Devices
Analog Devices ADSP-2181 Manuel utilisateur
Analog Devices
Analog Devices ADSP-BF535 Blackfin Guide d'application
Analog Devices
Analog Devices LTC2949 Manuel utilisateur
Analog Devices
Analog Devices SHARC ADSP-21367 Manuel utilisateur
Analog Devices
Analog Devices Linear ADP5070 Guide de configuration rapide
Analog Devices
Analog Devices EZ-KIT LITE ADSP-2191 Manuel utilisateur
Analog Devices
Analog Devices EZ-KIT Lite ADSP-21364 Manuel utilisateur
Analog Devices
Analog Devices ADSP-SC573 EZ-KIT Manuel utilisateur
Analog Devices
Analog Devices ADP8860SHIELD-EVALZ Manuel utilisateur
Analog Devices
Analog Devices SHARC ADSP-2136 Series Guide d'application
Analog Devices
Analog Devices EV-RPG2 Manuel utilisateur
Analog Devices
Analog Devices MICROCONVERTER ADUC812 Manuel utilisateur
Analog Devices
Analog Devices EVAL-AD7606SDZ Manuel utilisateur
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
