Amprobe TDR-400 Manuel utilisateur

Impulsreflektometer

TDR-400

Manual

BEHA-AMPROBE GmbH

In den Engematten 14, D-79286 Glottertal, Germany

Tel.: +49 (0) 7684-8009-0 Fax: +49 (0) 7684-8009-410

Impulse Reflectometer TDR-400

The TDR-400 is a handy, light impulse reflectometer, processor controlled, with LCD display

for check and locate faults in telecommunication and power cables.

Technical data

Display: LCD display, 120 x 32 pixel, illuminated

Power supply: NiMH accumulator 6 V/ 700 mAh (5 x R3),

Power consumption 80 mA

Dimensions: 157 x 84 x 30 mm

Operating: with 3 keys

Weight: 300 g

Measuring ranges

Measuring range 0 – 2000 m

Resolution 0.25m, 0.5m, 1m, 4m

Accuracy 0.2 % of the measuring range

Propagation factor 0.25 to 0.999

Storage places 10 for propagation factor

Dynamics 44 dB

Impedance 75 Ohm

Output F-socket

Output pulse 4 V / 5 ns or 100 ns

Operating

−Switch on: push key 1, after that push key 3. (accumulator full app. 7 V, empty app. 5.5V)

−Switch off: push simultaneously key 2 and 3, after 4 min. inactivity automatically.

If the accumulator voltage drops to 5.9 V, a fade-in happens on the display.

At 5.5 V the IRM switches off itself.

- Change between length measurement and length range: push shortly key 3

- Cursor move or range change: with key 1 or 2

- Fast cursor moving: keep key 1 or 2 pushed

- Selection of resolution, output pulse width, storage place or propagation factor:

push long key 3 until the desired symbol appears inversely.

change of the selected value with the keys 1 and 2.

Permanent storage: push keys 1 and 3 simultaneously.

back: push short key 3 .

- moving of the zero line:

The amplitude on the cursor position can be set to the zero line by pushing the keys 1 and

2 simultaneously. Because the IRM 5 has its highest sensitivity in the area of the zero

line, e.g. the graphical representation of the amplitude on the pulse peak can be seen.

This function can be cancelled by pushing the key 3.

- Start mode: If at a determined resolution the keys 1 and 3 are pushed simultaneously,

this resolution is at switch on of the IRM active.

- Charging: Plug power supply 2-24 V DC or AC on the charging socket 5,5 / 2,1 mm (+pole

inside).

Display of the power supply voltage (12-28 V) and charging monitoring on the display.

Propagation factors:

Mains cable 0.49–0.57, (ca. 0.53)

Coaxial cable with PE-dielectric 0.66

Coaxial cable with foam-PE 0.77–0.85

Air isolation

Determination of the propagation factor (nvp-value) of a cable:

Connect a cable of a known length (e.g. 100 m) on the IRM, set the cursor on the cable length

and change the propagation factor so, that the pulse echo is located behind the cursor.

Measuring principle:

The measuring pulse fed into the cable will reflected by in homogeneity of the cable impedance

(cable faults) and showed on the display.

The distance and the kind of the fault can be determined out of the shape and the time setting of

the reflection.

(Practical experience can be obtained by test measurements).

The Propagation factor (nvp-value) declares the velocity of electrical signals in the cable in

relation to the speed of light.

−The propagation factor of the cable under test must always preset before the length

measurement.

−If the propagation factor is unknown, a approximate value is set and the fault is determined

from both ends of the cable

Fault location:

ATTENTION ! No measurement on live cables ! (electric strength max. 65 V)

At 0 m the positive transmitting pulse can be seen. If the connected cable is open on its end, an

additional positive going pulse appears on the display. In the case of a shorted end of the cable a

negative going pulse appears reflected from the cable end (pulse echo).

Adjust the cursor to the beginning of the pulse and read the cable length.

If the cable is terminated with a resistance equal to the impedance of the cable, no reflexion

occurs when the cable is faultless.

In the case of breaks, contact faults in sleeves, short circuits or taps/splitter in the sector to be

tested, the distance to the cable beginning can be determined by the pulse echo.

If wide pulses are used for the measurement, the echoes are stronger, but faultless taps/splitter

cause then strong echoes.

Zero adjustment of the transmitting pulse:

Select a storage place of the propagation factor and push key 1 and 2 simultaneously up to

„-_∏_-“ appears on the display. Shift the transmitting pulse with key 1 or 2 so that the cursor is

located at beginning of the pulse.

Store this setting by pushing the keys 1 und 3 simultaneously.

Back to the normal operation with key 3.

Table des matières

Autres manuels Amprobe Instrument de mesure

Amprobe

Amprobe ACDC-620T Manuel utilisateur

Amprobe

Amprobe TMA10A Manuel utilisateur

Amprobe

Amprobe TMA40-A Manuel utilisateur

Amprobe

Amprobe SOLAR-500 Manuel utilisateur

Amprobe

Amprobe LH41A Manuel utilisateur

Amprobe

Amprobe ACD - 50NAV Manuel utilisateur

Amprobe

Amprobe LM-120 Manuel utilisateur

Amprobe

Amprobe VPC-10A Manuel utilisateur

Amprobe

Amprobe AMP-25 Manuel utilisateur

Amprobe

Amprobe CO2-100 Manuel utilisateur

Amprobe

Amprobe ACD-45PQ Manuel utilisateur

Amprobe

Amprobe UDM45 Manuel utilisateur

Amprobe

Amprobe 3434877 Manuel utilisateur

Amprobe

Amprobe LH41A Manuel utilisateur

Amprobe

Amprobe MANO2-A Manuel utilisateur

Amprobe

Amprobe AMP-25 Manuel utilisateur

Amprobe

Amprobe THWD-5 Manuel utilisateur

Amprobe

Amprobe TACH20 Manuel utilisateur

Amprobe

Amprobe VP-600SB Manuel utilisateur

Amprobe

Amprobe SM-10 Manuel utilisateur

Amprobe

Amprobe SOLAR-500 Manuel utilisateur

Amprobe

Amprobe LM631A Manuel utilisateur

Amprobe

Amprobe MAN15 Manuel utilisateur

Amprobe

Amprobe TMA-21HW Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur