Amprobe VPC-10 Manuel utilisateur

Voltage and Continuity Tester

Model VPC-10

Instruction Manual

m Safety Information

• Never use the tester if it or its test leads appear damaged

• Never apply more than 600V DC or 600V AC RMS between any terminal

and earth ground.

(If the LED turns on it indicates the presence of voltage at the probe tip.

• When using the probes, do not touch the metal probe tips.

• Disconnect the live test lead before disconnecting the common test lead.

• Before each use, verify the tester’s operation by measuring a known voltage.

Automatic Operation

The tester automatically turns on when you place the probes across a complete circuit.

The tester selects continuity or dc or ac voltage mode based on the resistance or volt-

age between the probes. The tester automatically turns off when you remove the

probes from the complete circuit.

Measuring Voltage

Connect test leads across the source or load under measurement, the LEDs turn on at

between 70% and 100% of their rated voltages.

Testing for Continuity

Turn off circuit power before testing

Beeper indicates shorts lasting 1ms or longer

OPEN SHORT or 0-85 KΩ

Specifications

Function Range Accuracy

AC voltage(V) 24,120,208,240,277,480,600 -30% to 0% of reading

DC voltage(V) 6,12,24,36,48,110,220 -30% to 0% of reading

Continuity test: Audible threshold 0-85kΩ, Continuity beeper 2KHz

Maximum Voltage Between any Terminal and Earth Ground:

600 V Overvoltage Category III

Input Impedance: 1MΩ

Temperature: Operating: 5˚C (41˚F) to 40˚C (104˚F)

Storage : -30°C to +60°C

Altitude: Operating: 2000m; Storage:10,000m

Relative Humidity:

80% for Temp up to 31˚C decreasing linearly to 50% RH at 40˚C

Battery Type and Life: AA(2); 350 hours with NEDA 15˚F or IEC R6

Safety: Complies with EN61010-1:1993 for use in overvoltage CAT III environments

Pollution Degree: 2

For indoor use only

EMC Regulations: EN50081-1, EN50082-1

DC Voltage

600V DC maximum

600

AC Voltage

600V RMS maximum

45Hz to 66Hz

Continuity Continuity

r Beeping

220V AC

Battery Test and Replacement

Replace the batteries when

touching the leads together no

longer turns on the

continuity LED.

WARRANTY

Congratulations! Your new instrument has been quality crafted according to quality

standards and contains quality components and workmanship. It has been inspected

for proper operation of all of its functions and tested by qualified factory technicians

according to the long-established standards of our company.

Your instrument has a limited warranty against defective materials and/or workmanship

for one-year from the date of purchase provided that, in the opinion of the factory, the

instrument has not been tampered with or taken apart.

Should your instrument fail due to defective materials, and/or workmanship during this

one-year period, a no charge repair or replacement will be made to the original pur-

chaser. Please have your dated bill of sale, which must identify the instrument model

number and serial number and call the number listed below:

Repair Department

ATP – Amprobe, TIF, Promax

Miramar, FL

Phone: 954-499-5400

800-327-5060

Fax : 954-499-5454

Website: www.amprobe.com

Please obtain an RMA number before returning product for repair. Outside the U.S.A.

the local representative will assist you. Above limited warranty covers repair and

replacement of instrument only and no other obligation is stated or implied.

P/N: ATP VPC-10Manual printed in China

2xAA

Disconnect probes from

Voltag. Do not over-tighten

screws

Miramara, Florida 33025

Tel: 954-499-5400 Toll Free: 800-327-5060 Fax: 954-499-5418

Autres manuels pour VPC-10

Autres manuels Amprobe Instrument de mesure

Amprobe

Amprobe ECB50A Manuel utilisateur

Amprobe

Amprobe TMA10A Manuel utilisateur

Amprobe

Amprobe WT-30 Manuel utilisateur

Amprobe

Amprobe PQ55A Manuel utilisateur

Amprobe

Amprobe TMA40-A Manuel utilisateur

Amprobe

Amprobe AC40C Manuel utilisateur

Amprobe

Amprobe SOLAR-500 Manuel utilisateur

Amprobe

Amprobe ACD-45PQ Manuel utilisateur

Amprobe

Amprobe PRM-4 Manuel utilisateur

Amprobe

Amprobe MO-100 Manuel utilisateur

Amprobe

Amprobe AM-33 Manuel utilisateur

Amprobe

Amprobe ACDC-620T Manuel utilisateur

Amprobe

Amprobe THWD-3 Manuel utilisateur

Amprobe

Amprobe LM-100 Manuel utilisateur

Amprobe

Amprobe AT-7020 Manuel utilisateur

Amprobe

Amprobe TMD-10 Manuel utilisateur

Amprobe

Amprobe AM-530 Manuel utilisateur

Amprobe

Amprobe CO2-100 Manuel utilisateur

Amprobe

Amprobe AC50A Manuel utilisateur

Amprobe

Amprobe MAN02-A Manuel utilisateur

Amprobe

Amprobe LT-10 Manuel utilisateur

Amprobe

Amprobe AT-6000-R Manuel utilisateur

Amprobe

Amprobe MAN02-A Manuel utilisateur

Amprobe

Amprobe ACD-51HP Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur