AJAX MotionProtect Plus Fibra Manuel utilisateur
MotionProtect Plus Fibra User Manual
Updated June 21, 2022
MotionProtect Plus Fibra — a wired motion detector with an additional
microwave sensor. It can recognize movement at a distance of up to 12 meters.
Together with the IR sensor, it applies a radio-frequency scan that lters out
thermal interference.
It does not react to animals up to 50 centimeters tall and weighing up to 20
kilograms when properly installed and congured. It is intended for indoor
installation.
The detector is compatible with and . Connection to
other , , , and is not
supported. Integration with other security systems is not provided
MotionProtect Plus Fibra only works as a part of the Ajax security system,
communicating with the hub via the secure Fibra protocol. The wired connection
range is up to 2000 meters when connected via the twisted pair U/UTP cat.5.
Hub Hybrid (2G) Hub Hybrid (4G)
hubs radio signal range extenders ocBridge Plus uartBridge
MotionProtect Plus Fibra is the device of the new Fibra wired product line. Such
devices can only be purchased, installed and administered by accredited Ajax
partners.
Functional elements
Operating principle
Buy MotionProtect Plus Fibra
1. LED indicator.
2. Motion detector lens.
3. SmartBracket mounting plate (to remove the plate, slide it down).
4. Perforated part of the mounting plate. Intended to trigger a tamper in case
of any attempt to detach the detector from the surface. Do not break it off.
5. Perforated part for wire output.
6. The hole for attaching the SmartBracket mounting panel with a screw.
7. . Triggers when an attempt is made to detach the detector
from the surface or remove the mounting panel.
Tamper button
8. QR code. Used to connect the detector to the Ajax security system.
9. Terminal block connection socket.
10. Terminal block for detector connection.
11. A hole for xing the wires with ties.
MotionProtect Plus Fibra is a wired motion detector with an additional
microwave sensor. Using the IR sensor, it can identify intrusions by detecting
moving objects with temperatures close to that of the human body.
When MotionProtect Plus Fibra detects motion, it conducts an additional RF
scan of the room to eliminate false alarms due to thermal interference: air ows,
heated curtains and blinds, fans, replaces, air conditioners, and other likely
sources of false alarms.
When an armed detector identies motion, it instantly sends an alarm to the
hub, which activates the sirens connected to the system, triggers , and
noties users and the security company. All MotionProtect Plus Fibra alerts and
events are recorded in the notication feed of the Ajax app.
Users know exactly where motion is detected. The notications contain the
name of the hub (name of the guarded object), the name of the device, and the
to which the detector is assigned.
The detector doesn’t go into armed mode instantly. The time it takes to switch to armed
mode depends on two factors: exit delays (specied in the detector settings) and the
hub – detector ping interval (Fibra settings, the default value is 36 seconds).In the rst
case, the delay is set by a user or a PRO with administrator rights. In the second case,
the delay occurs because it takes one ping interval for the hub to notify the detector
about the transition to armed mode.
scenarios
virtual room
How Ajax noties users of alerts
More about Ajax motion detectors
Fibra data transfer protocol
The detector uses Fibra technology to transmit alarms and events. This is a two-
way wired data transfer protocol that provides fast and reliable communication
between the hub and the rest of the devices. Using the bus connection method,
Fibra delivers alarms and events instantly, even if 100 detectors are connected
to the system.
Fibra supports oating key block encryption and veries each communication
session with devices to prevent sabotage and forgery. The protocol requires
regular polling of detectors by the hub with a predetermined frequency to
monitor communication and display the status of the system devices in real
time in the Ajax apps.
More about Fibra protocol (in progress)
Pet immunity
When properly installed and congured, MotionProtect Plus Fibra does not react
to animals up to 50 centimeters tall and weighing up to 20 kilograms.
The detector must be installed at a height of 2.4 meters without any obstruction
to its view — for example, in a corner where the view will not be blocked by a
closet or other furniture on which a pet can climb.
It is also important to set the proper sensitivity in the :
When indoor motion detectors are installed below the recommended height,
animals move in the hypersensitive zone. If a shepherd walks on its hind legs or
even a small spaniel plays on a chair, the detector can raise an alarm. The
detector will also raise an alarm if the animal is able to jump to the level of the
detector or move near it.
detector settings
High — the detector does not respond to cats (up to 25 cm tall).
Medium — it does not respond to small dogs (up to 35 cm tall).
Low — it does not respond to animals up to 50 cm tall.
Why detectors react to animals and how to avoid this
Temperature compensation
The detector perceives people and other objects as heat spots. The device
monitors these heat spots and, if they move, detects an alarm. MotionProtect
Plus Fibra reacts to the movement of heat spots whose temperature is close to
the human body.
When the ambient temperature is about the temperature of the human body, the
correct operation of the detector is not guaranteed unless temperature
compensation is applied. It is used in all Ajax motion detectors. With
temperature compensation, the detector recognizes motion across the entire
operating temperature range.
Sending events to the monitoring station
The Ajax security system can transmit alarms to the
monitoring app as well as the central monitoring station (CMS) in the formats of
the SurGard (Contact ID), SIA (DC-09), ADEMCO 685, and other proprietary
protocols. A complete list of supported protocols is .
MotionProtect Plus Fibra can transmit the following events:
How to install MotionProtect Plus Fibra correctly
Learn more
Ajax PRO Desktop
available here
Which CMSs can the Ajax security system be connected to
1. Motion alarm.
2. Tamper alarm / recovery.
3. Loss / restoration of connection to the hub.
4. Temporary deactivation / activation of the detector.
5. Unsuccessful attempt to arm the security system (with
enabled).
Integrity Check
When an alarm is received, the operator of the security company monitoring
station knows exactly what happened and precisely where to send a fast
response team on the site. Addressability of each Ajax device allows you to
send not only events to the PRO Desktop or to the CMS but also the type of the
device, the name of the device, and the virtual room to which the detector is
assigned. Note that the list of transmitted parameters may differ depending on
the type of CMS and the selected protocol for communication with the
monitoring station.
The device ID, the loop (zone) number, and the bus number can be found in its
.
Detector placement
When choosing where to place the detector, consider the parameters that affect
its normal operation: Fibra signal level, length of the cable for connecting the
detector, and the motion detection zone.
Consider the placement recommendations when designing your facility’s
security system. Design and installation of the security system should be
carried out by professionals. A list of authorized ocial Ajax partners is
.
Design and preparation
For the system to work correctly, it is important to properly design the project
and install all devices correctly. Failure to follow the basic installation rules and
recommendations of this manual may result in detector malfunction, false
alarms, or loss of connection with already installed devices.
When designing the layout scheme of the detectors, consider the wiring diagram
of the power cables laid on the site. Signal cables must be laid at a distance of
at least 50 cm from the power cables when lying parallel, and, if they intersect, it
must be at a 90° angle. Note that, if you connect multiple devices on the same
bus, detectors are connected in sequence.
The maximum number of connectable devices for the Hub Hybrid is 100 at the default
states in
the Ajax app
available here
settings.
How to calculate the number of connectable detectors (in progress)
For facilities that are under construction or renovation, cables are laid after the
main wiring of the facility. Use special protective tubes to route system cables
to organize and secure them; special ties, clips, and staples can be used to
secure the cables.
When laying cables externally (without mounting them inside the walls), use an
electric channel raceway. Raceways should be no more than half-lled with
cables. Do not allow cables to sag. The raceway should be hidden from view if
possible — for example, behind furniture.
We recommend laying cables inside walls, oors, and ceilings. This will provide greater
security: the cables will not be visible, and it will be impossible for an intruder to access
them.
When selecting a cable, consider the length of the connection lines and the
number of detectors to be connected; these parameters affect the signal
strength. We recommend using shielded copper cables with a high-quality
insulation layer.
When installing, observe the bend radius that the manufacturer species in the
cable specs. Otherwise, you risk damaging or breaking the conductor.
Be sure to check all cables for bends and physical damage before installation.
Perform the installation in a way that minimizes the possibility of damage to the
cables from the outside.
Signal strength and cable length
The Fibra signal level is determined by the number of undelivered or corrupted
data packages over a certain period. The icon on the Devices tab
indicates the signal strength:
Three bars — excellent signal strength.
The signal strength is inuenced by the following factors: the number of devices
connected to one bus, the length and type of cable, and the proper connection of
the wires to terminals.
Check the Fibra signal strength before nal installation of the detector. With a signal
strength of one or zero bars, we do not guarantee stable operation of the device.
The maximum permissible cable length depends on its type, its material, and the
method of connecting the devices. When connected via the beam connection
using the U/UTP cat.5 (4×2×0.51) twisted pair, the wired connection length can
reach up to 2,000 meters.
When devices are connected via the ring connection method, the maximum
cable length is 500 meters in case of using a twisted pair.
How to calculate the wire connection length (in progress)
Connecting devices using the ring connection method will be available with future OS
Malevich updates. Hardware update of Hub Hybrid won’t be required.
Detection zone
When choosing where to place the detector, perform the to
check the operation of the device and accurately determine the sector in which
the detector registers motion.
The location of the detector determines the area to be monitored and the
effectiveness of the security system. When choosing the installation location,
Two bars — good signal strength.
One bar — low signal strength, stable operation is not guaranteed.
Crossed out icon — no signal.
How OS Malevich updates
Detection zone test
consider the direction of the detector lens, its viewing angles, and the presence
of obstacles to the view of the lens.
The direction of the detector lens should be perpendicular to the intended path
of entry into the room.
Horizontal detector viewing angle
Vertical detector viewing angle
Do not install the detector
Installation and connection
1. Outdoors — This can lead to false alarms and detector failure.
2. In places where objects and structures can block the view of the detector —
For example, behind a ower or a column.
3. In places where glass structures may block the detector’s view; it doesn’t
register movement behind glass.
4. Inside premises with temperature and humidity outside the permissible
limits — This could damage the detector.
Before installing MotionProtect Plus Fibra, make sure that you have selected the optimal
location and that it meets the conditions of this manual. Cables must be hidden from
view and located in a place that is dicult for intruders to access to reduce the
likelihood of sabotage.
Ideally, mount them in the walls, oor, or ceiling. Before the nal installation, conduct
tests of the and the Fibra signal strength.
When connecting to the detector terminals, do not twist the wires together;
solder them. The ends of the wires that will be inserted into the terminals should
be tinned or crimped with special tips. This will ensure a reliable connection.
Follow safety procedures and regulations for electrical installation work.
In order to mount a detector:
detection zone
1. Disconnect the hub external power supply and the backup battery.
1 — External power supply
2 — Backup battery
2. Plug the cable into the hub and connect the wires to the bus terminals.
Table des matières
Autres manuels AJAX Capteur de sécurité
AJAX
AJAX CombiProtect Manuel utilisateur
AJAX
AJAX FireProtect 2 Manuel utilisateur
AJAX
AJAX MotionProtect Manuel utilisateur
AJAX
AJAX FireProtect Manuel utilisateur
AJAX
AJAX FireProtect 2 Jeweller Manuel utilisateur
AJAX
AJAX LeaksProtect Manuel utilisateur
AJAX
AJAX MotionProtect Curtain Manuel utilisateur
AJAX
AJAX GlassProtect Manuel utilisateur
AJAX
AJAX DoorProtect Manuel utilisateur
AJAX
AJAX vhfBridge Manuel utilisateur
AJAX
AJAX MotionProtect Manuel utilisateur
AJAX
AJAX DoorProtect Manuel utilisateur
AJAX
AJAX MotionCam Jeweller Manuel utilisateur
AJAX
AJAX DualCurtain Outdoor Manuel utilisateur
AJAX
AJAX DoorProtect Plus Jeweller Manuel utilisateur
AJAX
AJAX DoorProtect Plus Manuel utilisateur
AJAX
AJAX GlassProtect Manuel utilisateur
AJAX
AJAX MotionProtect Manuel utilisateur
AJAX
AJAX DoorProtect Plus Manuel utilisateur
AJAX
AJAX MotionProtect Manuel utilisateur
